SME 3009 Series III Black Pipe Static Balance Type Tonearm Pickup Arm Vintage Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels. Lifter descent speed. Each adjustment point, operation feeling. Height adjustment, etc. Polished / cleaned for each part.The appearance is a beautiful product without any noticeable scratches. For other appearances, please refer to the photo. Damping oil is drained to prevent oil leakage during transportation. Please replenish the included damping oil at the time of use. *Turntables and other equipment shown in the photo, other than the 3009, are for presentation purposes only and are not included in the product. Specifications Type: Static balance typeEffective length: 229.0mmCenter of Slide Base to Center of Turntable :215.9mmSlide base travel range: ±12.7mm Overview Highly sensitive tone arm compatible with ultra-lightweight, high-compliance cartridges. SMEs unique carrying arm system, which integrates the shell and pipe arm into a single unit, is used to dampen harmful vibrations. The pipe arm is made of ultra-thin titanium, with only the surface of the pipe hardened by nitrogen hardening treatment, and the interior lined with a fibrous lining to naturally dampen the micro-vibrations transmitted from the cartridge.This carrying arm pipe is a CA-1/BLACK pipe specification, which is rarely distributed.In addition, carbon fiber processed by a 100-ton press is used for the main weights and other parts that require weight, to further increase sensitivity and reduce the moment of inertia. The shell section is made of carbon fiber. Carbon fiber is used for the knife-edge part, a typical SME technology.Furthermore, by placing the knife edge at a right angle to the direction of the headshell, the tip of the edge is aligned at the same height as the stylus of a standard cartridge, and the main weight is placed below the height of the pipe arm. This new fulcrum arrangement successfully reduces the frictional resistance of the knife edge to near zero.This structure also works effectively against the arm lifting phenomenon. A unique fluid damper is provided to reduce low-frequency resonance and mechanical vibration of the entire pickup system when a cartridge is mounted.This damper uses the oil dump method, which utilizes the flow characteristics of silicon fluid to reduce low-frequency resonance, which is a slight resonance but has a significant effect on the low-frequency range. Accessories Internal weight (large lead plate x 1 / small lead plate x 4 / spacer x 1)?(usable cartridge weight: approx. 7.0g to 12.0g)Inside force canceller weightSME cableOil dump partsDamping oilInstruction Manual (copy)(Japanese)Alignment Protractor (copy)Mounting plate (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

SME 3009 Series IIIS Static Balance Type Tonearm Pickup Arm Vintage Audio w/Box Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels. Lifter descent speed. Each adjustment point, operation feeling. Height adjustment, etc. Polished / cleaned for each part.The appearance is a beautiful product without any noticeable scratches. For other appearances, please refer to the photo. Damping oil is drained to prevent oil leakage during transportation. Please replenish the included damping oil at the time of use. *Turntables and other equipment shown in the photo, other than the 3009, are for presentation purposes only and are not included in the product. Specifications Type: Static balance typeEffective length: 229.0mmCenter of Slide Base to Center of Turntable :215.9mmSlide base travel range: ±12.7mm Overview While the SIIIs needle pressure adjustment and inside force canceller are rotary systems that can be fine-tuned, the SIIIS uses a simple slide system. SMEs unique carrying arm system, which integrates the shell and pipe arm into a single unit, is used to dampen harmful vibrations. The pipe arm is made of ultra-thin titanium, and only the surface of the pipe is hardened by nitrogen hardening treatment, while the interior is lined with a fibrous lining to naturally dampen micro-vibrations transmitted from the cartridge.In addition, carbon fiber processed by a 100-ton press is used for the main weights and other parts that require weight, to further increase sensitivity and reduce the moment of inertia. The shell section is made of carbon fiber. Carbon fiber is used for the knife-edge part, a typical SME technology.Furthermore, by placing the knife edge at a right angle to the direction of the headshell, the tip of the edge is aligned at the same height as the stylus of a standard cartridge, and the main weight is placed below the height of the pipe arm. This new fulcrum arrangement successfully reduces the frictional resistance of the knife edge to near zero.This structure also works effectively against the arm lifting phenomenon. Accessories Needle pressure adjustment weight/auxiliary weight (pre-installed)Internal lead weights x 5?(usable cartridge weight: from 0.2g to 13.7g)Inside force canceller weight/pulleyFixing wood screws x 4SME cable / ground wireOil dump parts / Damping oilInstruction Manual (copy)(Japanese)Alignment Protractor (copy)Mounting plate (original)Original box Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

SME 3009 Series III Static Balance Type Tonearm Pickup Arm Vintage Audio Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels. Lifter descent speed. Each adjustment point, operation feeling. Height adjustment, etc. Polished / cleaned for each part.The appearance is a beautiful product without any noticeable scratches. For other appearances, please refer to the photo. Damping oil is drained to prevent oil leakage during transportation. Please replenish the included damping oil at the time of use. *Turntables and other equipment shown in the photo, other than the 3009, are for presentation purposes only and are not included in the product. Specifications Type: Static balance typeEffective length: 229.0mmCenter of Slide Base to Center of Turntable :215.9mmSlide base travel range: ±12.7mm Overview While the SIIIs needle pressure adjustment and inside force canceller are rotary systems that can be fine-tuned, the SIIIS uses a simple slide system. SMEs unique carrying arm system, which integrates the shell and pipe arm into a single unit, is used to dampen harmful vibrations. The pipe arm is made of ultra-thin titanium, and only the surface of the pipe is hardened by nitrogen hardening treatment, while the interior is lined with a fibrous lining to naturally dampen micro-vibrations transmitted from the cartridge.In addition, carbon fiber processed by a 100-ton press is used for the main weights and other parts that require weight, to further increase sensitivity and reduce the moment of inertia. The shell section is made of carbon fiber. Carbon fiber is used for the knife-edge part, a typical SME technology.Furthermore, by placing the knife edge at a right angle to the direction of the headshell, the tip of the edge is aligned at the same height as the stylus of a standard cartridge, and the main weight is placed below the height of the pipe arm. This new fulcrum arrangement successfully reduces the frictional resistance of the knife edge to near zero.This structure also works effectively against the arm lifting phenomenon. Accessories Internal weight (large lead plate x 1 / small lead plate x 5)?(usable cartridge weight: from approx. 8.0g to 13.0g)Inside force canceller weightSME cableWood screws for fixing arm x 4Oil dump partsDamping oilInstruction Manual (Original Japanese *Damaged due to age.)Alignment Protractor (copy)Mounting plate (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Restored Thorens Td 160 Mkii Turntable & Sme Series III Tracking ArmThe description of this item has been automatically translated. If you have any questions, please feel free to contact us.Individual production! Please note the processing time stated on Ebay! Individual production! Please note the processing time specified on Ebay! This turntable is available in 220V/230/ 50Hz or 110V/120/60Hz (for example USA)DANGER! The following change applies! The turntable plate is no longer delivered in polished but in matt black!DANGER! The following change applies! The turntable plate is no longer delivered in polished but in matt black!You can find even more interesting offers from us. Take a look at... Art and Sound GermanyRESTORED by ART-AND-SOUND 160 MKII with SME Series III tonearmOur record players are lovingly put together and assembled by hand.Each of them is unique and differs in model, color and veneer grain.The high-quality housings are restored or newly manufactured using qualified craftsmanship.Electrical components are checked, Moving parts oiled and wearing parts replaced.A final endurance test rounds off the complex work. Item description:Limit switch:     NoInner plate: metalBearing mandrel: 7mm Basic dimensions:            Width 45cm, depth 36cm, height 18cm The housing:The housing consists of 25mm MDF side panels and a 16mm thick base made of the same material. It is very complex with several layers of high-gloss varnish sealed and polished with appropriate intermediate sanding. The connection panel for all required cable connections is located on the back.Faceplate:Cover plate made of 1mm aluminum with surface anodization in a gold lookThe Ortofon Vinyl Master Alpha cartridge:The Ortofon Alpha is a full-fledged pickup. It impresses with its temperament and neutral basic character. The VinylMaster Alpha features an elliptical stylus that allows for balanced and distortion-free playback.The audio cable:Branded cable. Ready-made analog audio cinch cable for cabling turntables! Thanks to the particularly high-quality inner conductor made of oxygen-free copper (OFC), this quality cable ensures true-to-life signal transmission. Contact security and corrosion protection are guaranteed by the 24 carat gold-plated plug contacts. The cable has a neutral sound with good dynamics and spaciousness.The turntable:The turntable is painted matt black. It gives your record player a lasting and discreet elegance.Spikes made of chrome-plated stainless steel:So that the record player is decoupled from low-frequency vibrations, The chassis is equipped with height-adjustable spikes. Resonances and feedback are thus effectively prevented. The drive belt:The drive belt is new. It is manufactured according to the original Thorens specifications (same material and same dimensions).The following Parts are as Accessoriesör erhäliltic and not component this auction:The following parts are available as accessories and not included in this auction:Hood small (to be placed on the frame): 160Hood big (for placing on the substructure): 180 Cartridge MM system including installation:Ortofon VinylMaster Red (elliptical): 190 Ortofon VinylMaster Silver (Fritz Gyger, naked): 390Ortofon 2M Red (elliptical): 90 Ortofon 2M Blue (elliptical, naked): 190 Ortofon 2M Bronze (fineline): 390Ortofon 2M Black (Shibata): 590Ortofon 2M Black LVB 250: 890 Cartridge MC System including installation: AUDIO-TECHNICA AT-OC9XML (microlinear): 599AUDIO TECHNICA AT-OC9XSH (Shibata): 699AUDIO-TECHNICA AT-OC9XSL (Special Line Contact): 799 The housing consists of 25mm MDF side panels and a 16mm thick base made of the same material. It is very complex with several layers of high-gloss varnish sealed and polished with appropriate intermediate sanding. The connection panel for all required cable connections is located on the back. The Ortofon Alpha is a full-fledged pickup. It impresses with its temperament and neutral basic character. The VinylMaster Alpha features an elliptical stylus that allows for balanced and distortion-free playback. Branded cable. Ready-made analog audio cinch cable for cabling turntables! Thanks to the particularly high-quality inner conductor made of oxygen-free copper (OFC), this quality cable ensures true-to-life signal transmission. Contact security and corrosion protection are guaranteed by the 24 Herstellernummer nicht zutreffend Marke Thorens - restauriert von art-and-sound EAN Nicht zutreffend Modell TD160 MKII

Restored Thorens TD 160 Turntable Sme 3009 Series III Tracking ArmThe description of this item has been automatically translated. If you have any questions, please feel free to contact us.Individual production! Please note the processing time stated on Ebay! Individual production! Please note the processing time specified on Ebay! This turntable is available in 220V/230/ 50Hz or 110V/120/60Hz (for example USA)DANGER! The following change applies! The turntable plate is no longer delivered in polished but in matt black!DANGER! The following change applies! The turntable plate is no longer delivered in polished but in matt black!You can find even more interesting offers from us. Take a look at... Art and Sound GermanyRESTORED by ART-AND-SOUNDThorens TD160 with SME Series IIIItem description:Limit switch:    NoInner plate:             metalSpindle:                   10mm Basic dimensions:            Width: 45cm, depth: 36cm, height approx. 18cmHousing:The housing consists of 25mm MDF side panels and a 16mm thick base made of the same material. It is elaborate with several layers of high-gloss varnish sealed and polished with appropriate intermediate sanding. The connection panel for all required cable connections is located on the back. The bottom of the case is equipped with three openings for horizontal alignment of the turntable.Cover plate:New cover plate made of 1mm brushed stainless steelOrtofon Vinyl Master Alpha pickup:The Ortofon Alpha is a full-fledged pickup. It impresses with its temperament and neutral basic character. The VinylMaster Alpha features an elliptical stylus that allows for balanced and distortion-free playback.Audio cable:Branded cable from Oelbach. Ready-made analog audio cinch cable for cabling turntables! Thanks to the particularly high-quality inner conductor made of oxygen-free copper (OFC), this quality cable ensures true-to-life signal transmission. Contact security and corrosion protection are guaranteed by the 24 carat gold-plated plug contacts. The cable has a neutral sound with good dynamics and spaciousness.Turntable:The turntable is painted matt black. It gives your record player a lasting and discreet elegance.Turntable feet:Four height-adjustable spikes made of chrome-plated stainless steel. New drive belt:This drive belt is manufactured according to the original Thorens specifications (same material and dimensions).Stainless steel record weight:With a weight of 310g, it ensures that the record sits smoothly on the plate and runs smoothly. This record weight is in the middle weight class. It builds up just enough weight to dampen the vibrations of the plate without putting any strain on the bearing bushes. The suspension of the Thorens sub-chassis was readjusted accordingly. By using it, you increase the sound performance of your system.The following Parts are as Accessoriesör erhäliltic and not component this auction:The following parts are available as accessories and not included in this auction:Hood small (to be placed on the frame): 160Hood big (for placing on the substructure): 180 Cartridge MM system including installation:Ortofon VinylMaster Red (elliptical): 190 Ortofon VinylMaster Silver (Fritz Gyger, naked): 390Ortofon 2M Red (elliptical): 90 Ortofon 2M Blue (elliptical, naked): 190 Ortofon 2M Bronze (fineline): 390Ortofon 2M Black (Shibata): 590Ortofon 2M Black LVB 250: 890 Cartridge MC System including installation: AUDIO-TECHNICA AT-OC9XML (microlinear): 599AUDIO TECHNICA AT-OC9XSH (Shibata): 699AUDIO-TECHNICA AT-OC9XSL (Special Line Contact): 799Branded cable from Oelbach. Ready-made analog audio cinch cable for cabling turntables! Thanks to the particularly high-quality inner conductor made of oxygen-free copper (OFC), this quality cable ensures true-to-life signal transmission. Contact security and corrosion protection are guaranteed by the 24 carat gold-plated plug contacts. The cable has a neutral sound with good dynamics and spaciousness. With a weight of 310g, it ensures that the record sits smoothly on the plate and runs smoothly. This record weight is in the middle weight class. It builds up just enough weight to dampen the vibrations of the plate without putting any strain on the bearing bushes. The suspension of the Thorens sub-chassis was readjusted accordingly. By using it, you increase the sound performance of your Herstellernummer nicht zutreffend Marke Thorens - restauriert von art-and-sound EAN Nicht zutreffend Modell TD 160

Original SME Series III S Tracking ArmThe description of this item has been automatically translated. If you have any questions, please feel free to contact us.Original SME Series III S tonearmoptically very good condition(the tonearm stand is not part of the offer)Original SME Series III S tonearm optically very good condition (the tonearm stand is not part of the offer) Herstellernummer nicht zutreffend Marke SME Markenkompatibilität Universell Produktart Tonarm EAN Nicht zutreffend

Sme Series III Tracking Arm Weights Additional Weights Tonearm Weight No. 3203The description of this item has been automatically translated. If you have any questions, please feel free to contact us.SME Series IIIAdditional weights for the tonearmContents see photoSME Series III Additional weights for the tonearm Contents see photo

SME 3009 Series III Static Balance Type Tonearm Pickup Arm Vintage Audio Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels. Lifter descent speed. Each adjustment point, operation feeling. Height adjustment, etc. Polished / cleaned for each part.The appearance is a beautiful product without any noticeable scratches. For other appearances, please refer to the photo. Damping oil is drained to prevent oil leakage during transportation. Please replenish the included damping oil at the time of use. *Turntables and other equipment shown in the photo, other than the 3009, are for presentation purposes only and are not included in the product. Specifications Type: Static balance typeEffective length: 229.0mmCenter of Slide Base to Center of Turntable :215.9mmSlide base travel range: ±12.7mm Overview While the SIIIs needle pressure adjustment and inside force canceller are rotary systems that can be fine-tuned, the SIIIS uses a simple slide system. SMEs unique carrying arm system, which integrates the shell and pipe arm into a single unit, is used to dampen harmful vibrations. The pipe arm is made of ultra-thin titanium, and only the surface of the pipe is hardened by nitrogen hardening treatment, while the interior is lined with a fibrous lining to naturally dampen micro-vibrations transmitted from the cartridge.In addition, carbon fiber processed by a 100-ton press is used for the main weights and other parts that require weight, to further increase sensitivity and reduce the moment of inertia. The shell section is made of carbon fiber. Carbon fiber is used for the knife-edge part, a typical SME technology.Furthermore, by placing the knife edge at a right angle to the direction of the headshell, the tip of the edge is aligned at the same height as the stylus of a standard cartridge, and the main weight is placed below the height of the pipe arm. This new fulcrum arrangement successfully reduces the frictional resistance of the knife edge to near zero.This structure also works effectively against the arm lifting phenomenon. Accessories Internal weight (large lead plate x 1 / small lead plate x 5)?(usable cartridge weight: from approx. 8.0g to 13.0g)Inside force canceller weightSME cableWood screws for fixing arm x 4Oil dump partsDamping oilInstruction Manual (Original Japanese *Damaged due to age.)Alignment Protractor (copy)Mounting plate (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

SME 3009 Series III Static Balance Type Tonearm Pickup Arm Vintage Audio Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels. Lifter descent speed. Each adjustment point, operation feeling. Height adjustment, etc. Polished / cleaned for each part.The appearance is a beautiful product without any noticeable scratches. For other appearances, please refer to the photo. Damping oil is drained to prevent oil leakage during transportation. Please replenish the included damping oil at the time of use. *Turntables and other equipment shown in the photo, other than the 3009, are for presentation purposes only and are not included in the product. Specifications Type: Static balance typeEffective length: 229.0mmCenter of Slide Base to Center of Turntable :215.9mmSlide base travel range: ±12.7mm Overview While the SIIIs needle pressure adjustment and inside force canceller are rotary systems that can be fine-tuned, the SIIIS uses a simple slide system. SMEs unique carrying arm system, which integrates the shell and pipe arm into a single unit, is used to dampen harmful vibrations. The pipe arm is made of ultra-thin titanium, and only the surface of the pipe is hardened by nitrogen hardening treatment, while the interior is lined with a fibrous lining to naturally dampen micro-vibrations transmitted from the cartridge.In addition, carbon fiber processed by a 100-ton press is used for the main weights and other parts that require weight, to further increase sensitivity and reduce the moment of inertia. The shell section is made of carbon fiber. Carbon fiber is used for the knife-edge part, a typical SME technology.Furthermore, by placing the knife edge at a right angle to the direction of the headshell, the tip of the edge is aligned at the same height as the stylus of a standard cartridge, and the main weight is placed below the height of the pipe arm. This new fulcrum arrangement successfully reduces the frictional resistance of the knife edge to near zero.This structure also works effectively against the arm lifting phenomenon. Accessories Internal weight (large lead plate x 1 / small lead plate x 5)?(usable cartridge weight: from approx. 8.0g to 13.0g)Inside force canceller weightSME cableWood screws for fixing arm x 4Oil dump partsDamping oilInstruction Manual (Original Japanese *Damaged due to age.)Alignment Protractor (copy)Mounting plate (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Sme Series III Tracking Arm Weights Additional Weights Tonearm Weight No. 3203The description of this item has been automatically translated. If you have any questions, please feel free to contact us.SME Series IIIAdditional weights for the tonearmContents see photoSME Series III Additional weights for the tonearm Contents see photo

Sme Series III Tracking Arm Weights Additional Weights Tonearm Weight No. 3203The description of this item has been automatically translated. If you have any questions, please feel free to contact us.SME Series IIIAdditional weights for the tonearmContents see photoSME Series III Additional weights for the tonearm Contents see photo

Just pulled off my luxman which I will be selling also in a different listing. Great working unit! Lift mech is smooth. Comes complete with sme original rca cable

**MISSING BIAS WEIGHT AND LINE** ** NO RCA’S ARE INCLUDED** Only what’s pictured is included in the sale. Please see photos.

Vintage Shure SME 3009 series IIIS Tonearm Pick-up Arm This appears to be in like new condition. It has been packaged taken apart and pictured the same way. No arm board.Sold as you see . Please inspect the photos. Sold as is .

Vintage Shure SME 3009 series IIIS Tonearm Pick-up Arm This appears to be in like new condition. It has been packaged taken apart and pictured the same way. No arm board.Sold as you see . Please inspect the photos. Sold as is .

Sme Series III Tracking Arm Weights Additional Weights Tonearm Weight No. 3203The description of this item has been automatically translated. If you have any questions, please feel free to contact us.SME Series IIIAdditional weights for the tonearmContents see photoSME Series III Additional weights for the tonearm Contents see photo

SME Series IIIAdditional weights for the tonearmContents see photoSME Series III Additional weights for the tonearm Contents see photo

SME 3009 Series III tone arm with Thorens 125 arm board. It appears to have all its parts and in the original box. I have not used this tone arm and am selling it as is for parts only. Feel free to let me know if you have any questions or need any additional information. Cheers al Heres what the Ai has to say about this tone arm. This SME Tonearm Model 3009 Series III is a top-quality turntable accessory designed to enhance your music listening experience. It is compatible with SME and is made with high-quality materials to ensure longevity. The black color gives it a sleek and stylish look that will complement any setup.With its precise design, this tonearm is perfect for audiophiles who want to experience the full range of their vinyl records. It is easy to install and use, making it a great addition to any record player. Whether youre a seasoned collector or just starting out, this SME Tonearm is a must-have for anyone who wants to enjoy their music in the highest quality possible.

We deliver rare, authentic items from Japan for YOU! CrowdTrading Japan LLC, a licensed secondhand dealer (ID: 542532302400), is your gateway to rare and authentic items (even obsoleted items). Our founders expertise and vast suppliers network in Japan empower us to source elusive items, from industrial machinery and auto parts to audio and consumer gaming gears. Trust us for unparalleled finds at fair prices. Experience our extraordinary service today. Condition and Item Specific Information *Note: Were NOT the original manufacturers, so while we do our best to describe items accurately, details provided below are NOT guaranteed. For used goods, check the official specs provided from original manufacturers and rely on item photos. Buyer discretion is advised. Condition: This listing includes all the accessories shown in the photos. Please note that there is some tarnish and dirt on the metal parts due to age. The items functionality has been tested and confirmed to work well. It should be noted that there might be natural signs of aging on the product, even if minor, depending on individual sensitivity. We encourage potential buyers to thoroughly review the product photos, descriptions, and specifications before considering a purchase. Please do not hesitate to contact us if you need further details. Description (if any, other than ones available in other sections of this page): Please refer to the official website or the original manufacturers specifications for accurate information.SME 3009 Series III tonearm Specifications | Stereophile.com *For products that plug into an outlet for use or charging. Voltage differences outside of Japan (100V) may cause malfunctions. We strongly recommend using a voltage transformer which you can get through Amazon or local EC sites etc.. The below table outlines the differences in voltage and frequency by countries for your easy reference. International Buyers - Please Note Import duties, taxes, and charges are NOT included in the item price or shipping cost. These charges are the buyers responsibility. Import duty is imposed to an item whose price exceeds a certain threshold depending on your shipping location. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying. Again, if you are NOT willing to take responsibility of paying such charges, import duties, taxes, etc., please do NOT purchase from international sellers like us. We clearly state here that we do NOT cover full or partial of your import duties, taxes, and any charges which are buyers responsibility in general importing/exporting practices. For products that plug into an outlet for use or charging, voltage differences outside of Japan (where the voltage is 100V) may cause malfunctions. We strongly recommend using a voltage transformer. By purchasing an item, it is considered that youve read and agreed the above terms and conditions and to follow general importing/exporting practices. Contact us We can be contacted at any time through eBay messages if you have any questions, comments or product requests. We will respond to you at our earliest convenience and do our best to help you out! Payment Payment methods we accept are: Managed Payments (Credit Card, PayPal, Apple Pay, Google Pay etc.) Please make a payment within 3 days after received our invoice or placed your order. Shipping We ship WORLDWIDE (some exceptions may apply) We use courier (mostly FedEx or DHL) and Japan Post, depending on a shipping address, an item price, an item condition etc. We provide you with tracking No. *exceptions may apply. Due to the pandemic, please be mindful that there may be unexpected delays depending on your location and supply chain status. If you buy multiple items in one-go, you may receive discount on shipping cost (please ask in advance. Once shipped out, it is impossible to change a shipping method). In case of returning an item, we may ask you to return the item by your local post office or the most reasonable shipping method. In such a case, we reimburse you the shipping cost through PayPal (this is currently the only payment method we can offer for reimbursement) after confirming the shipping cost receipt.

Restored Thorens Td 160 Mkii Turntable & Sme Series III Tracking ArmThe description of this item has been automatically translated. If you have any questions, please feel free to contact us.Individual production! Please note the processing time stated on Ebay! Individual production! Please note the processing time specified on Ebay! This turntable is available in 220V/230/ 50Hz or 110V/120/60Hz (for example USA)DANGER! The following change applies! The turntable plate is no longer delivered in polished but in matt black!DANGER! The following change applies! The turntable plate is no longer delivered in polished but in matt black!You can find even more interesting offers from us. Take a look at... Art and Sound GermanyRESTORED by ART-AND-SOUND 160 MKII with SME Series III tonearmOur record players are lovingly put together and assembled by hand.Each of them is unique and differs in model, color and veneer grain.The high-quality housings are restored or newly manufactured using qualified craftsmanship.Electrical components are checked, Moving parts oiled and wearing parts replaced.A final endurance test rounds off the complex work. Item description:Limit switch:     NoInner plate: metalBearing mandrel: 7mm Basic dimensions:            Width 45cm, depth 36cm, height 18cm The housing:The housing consists of 25mm MDF side panels and a 16mm thick base made of the same material. It is very complex with several layers of high-gloss varnish sealed and polished with appropriate intermediate sanding. The connection panel for all required cable connections is located on the back.Faceplate:Cover plate made of 1mm aluminum with surface anodization in a gold lookThe Ortofon Vinyl Master Alpha cartridge:The Ortofon Alpha is a full-fledged pickup. It impresses with its temperament and neutral basic character. The VinylMaster Alpha features an elliptical stylus that allows for balanced and distortion-free playback.The audio cable:Branded cable. Ready-made analog audio cinch cable for cabling turntables! Thanks to the particularly high-quality inner conductor made of oxygen-free copper (OFC), this quality cable ensures true-to-life signal transmission. Contact security and corrosion protection are guaranteed by the 24 carat gold-plated plug contacts. The cable has a neutral sound with good dynamics and spaciousness.The turntable:The turntable is painted matt black. It gives your record player a lasting and discreet elegance.Spikes made of chrome-plated stainless steel:So that the record player is decoupled from low-frequency vibrations, The chassis is equipped with height-adjustable spikes. Resonances and feedback are thus effectively prevented. The drive belt:The drive belt is new. It is manufactured according to the original Thorens specifications (same material and same dimensions).The following Parts are as Accessoriesör erhäliltic and not component this auction:The following parts are available as accessories and not included in this auction:Hood small (to be placed on the frame): 160Hood big (for placing on the substructure): 180 Cartridge MM system including installation:Ortofon VinylMaster Red (elliptical): 190 Ortofon VinylMaster Silver (Fritz Gyger, naked): 390Ortofon 2M Red (elliptical): 90 Ortofon 2M Blue (elliptical, naked): 190 Ortofon 2M Bronze (fineline): 390Ortofon 2M Black (Shibata): 590Ortofon 2M Black LVB 250: 890 Cartridge MC System including installation: AUDIO-TECHNICA AT-OC9XML (microlinear): 599AUDIO TECHNICA AT-OC9XSH (Shibata): 699AUDIO-TECHNICA AT-OC9XSL (Special Line Contact): 799 The housing consists of 25mm MDF side panels and a 16mm thick base made of the same material. It is very complex with several layers of high-gloss varnish sealed and polished with appropriate intermediate sanding. The connection panel for all required cable connections is located on the back. The Ortofon Alpha is a full-fledged pickup. It impresses with its temperament and neutral basic character. The VinylMaster Alpha features an elliptical stylus that allows for balanced and distortion-free playback. Branded cable. Ready-made analog audio cinch cable for cabling turntables! Thanks to the particularly high-quality inner conductor made of oxygen-free copper (OFC), this quality cable ensures true-to-life signal transmission. Contact security and corrosion protection are guaranteed by the 24 Herstellernummer nicht zutreffend Marke Thorens - restauriert von art-and-sound EAN Nicht zutreffend Modell TD160 MKII

Heute biete ich Ihnen folgendes an: SME 3009 Series III Tonarm Tonearm technischer Zustand: guter Zustand optischer Zustand: guter Zustand Falls Sie den oben aufgeführten Artikel ersteigern und diesen persönlich bei mir abholen, so können wir diesen sehr gerne gemeinsam auf den von mir angegebenen Zustand hin überprüfen. Kein Versand an Packstationen oder Paketshops !!! No shipping to USA

SME SERIES III Tonearm Paperwork And Parts. Most of the little parts and tools are bagged but the band is loose (not sure what condition the rubber is in)

Very rare Vieta G900 direct drive turntable. 2 speeds 33 & 45rpm controled by quartz. Also variable velocity with pitch and stroboscope light. SME series III tonearm. Shure ML140HE and stylus. It is adjusted to weight and antiskating. The plinth is made of wood and marble. Glossy black lacquer finish. Minor marks on the aluminium plate. The plinth is excellent and also the cover. No deep scratches, dents, shocks or cracks. In general, good cosmetic condition. In excellent working order. This item will be dispatched well packaged with tracking number.

Used SME Tonearm wand. Payment due within 3 days of purchase.