Siemens Klangfilm Typ Sf. L 6.2 Lautsprecher restauriert in Top Zustand vintage speaker Nennimpedanz: 5 OhmBreite: ca. 47 cmHöhe: ca. 45 cm (inkl. Standfüße und Tragegriff ca. 48 cm)Tiefe: ca. 25 cmGewicht: ca. 8,6 kg Länge des enthaltenen Lautsprecherkabels: ca. 15 m Der Lautsprecher wurde aufwändig restauriert:Die eingesetzten Hoch- und Tieftönlautsprecher entsprechen den damals von Isophon an Siemens zugelieferten Typen sind von ausgesucht guter Qualität. Die Innenverkabelung entspricht den hohen technischen und qualitativen Anforderungen. Das Gehäuse war vom Vorbesitzer für den Einbau eines anderen Tiefton-Lautsprecher-Chassis geändert worden. Das machte für eine werkgetreue Restaurierung die Erneuerung der Schallwand notwendig (daher der geringfügige Farbunterschied zum Rest der Innenwände).Das Lautsprecherkabel wurde an beiden Enden mit den passenden Steckern ausgestattet. Zustand nach Restauration: Gebraucht - aber dem Alter entsprechend sehr gut erhalteneinwandfreie Funktion beim durchgeführten Testbetriebnur sehr geringe Gebrauchsspuren am Gehäuse keine Beschädigungen der Beschlägekeine Beschädigungen der Lautsprechermembranen und Aufhängungenweitere Einzelheiten entnehmen Sie bitte den Fotos, sie sind Bestandteil der Artikelbeschreibung Lieferumfang: 1 Stück Lautsprecher Siemens Klangfilm Typ Sf. L 6.2 Lautsprecher (wie auf den Fotos zu sehen). Falls eine erneute Änderung der Lautsprecherbestückung geplant sein sollte, kann ich - auf Wunsch - gerne die alte Schallwand als Bohrschablone beilegen (siehe letztes Foto). Der Lautsprecher wird gut und sicher verpackt. Versand mit DHL-Paket mit mehr als 10 kg. Dies ist ein Privatverkauf, Garantie und Rücknahme sind ausgeschlossen.

For sale is a matched pair of the very rare and highly wanted vintage output transformers type BV 7105/2. These transformers are interleaved - both secondary coils are connected parallelly already. This connection makes the frequency response from 30 Hz to 18 kHz.These output transformers are perfect applicable for SE power stages with aAD1, ED, RE604, EL12, AL5/EL5, F2a11, or other tubes, with output impedance in the area between 2,2 kOhm to 5 kOhm. The max. power capacity is ca. 8-10 Watt and the ratio is 1:18. With the ratio about 1:18 these output transformers are suitable for following application: For Example: AD1/ ED Single End - 5 Watt, (U supply 300V, Ua 250 V, Grid -45 V,cathode resistor 750 Ohm) Ra 2,3 kOhm - usable output impedance 6-8 Ohm respectively with RE604 with changing the cathode resistor of 1000 Ohm RE 604 Single End - 2-3 Watt (U supply 300V, Ua 250 V, Grid -45V, cathode resistor 1000 Ohm) Ra 3,5 - 3,8 kOhm - usable output impedance 8-12 OhmOther solution with the BV 7105: EL12 / EL6 Single End - 8,2 Watt (Ua 250 V, Screen 250 V, Grid -7 V) Ra 4 - 5 kOhm - output impedance 12-15 Ohm (this was the original application) EL5 / AL5 Single End - 8,5 Watt (Ua 250V, Screen 275 V, Grid -14 V) Ra 4 - 5 kOhm - output impedance 12-15 Ohm F2A / F2a11 Single End - 10 Watt, (Ua 250 V, Screen 250 V, Grid -7 V- as in Klangfilm Kl. V204) Ra 2,2 - 2,4 kOhm - usable output impedance 6-8 Ohm The normal output transformers constructed for PP power stages, and as well so called match transformers for adaptation of low impedance speakers for high impedance amplifier outputs, are not suitable for using with a SE power stage!! The iron core for OPT in a SE power stage must be assembled with so called magnet slit For creation of a magnet slit all iron sheets must be interposed in one direction only. Therefore the BV 7105 are perfectly suitable for application of the RE604respectively AD1, or for each other power triode or pentode with Ra output resistance about2,2 - 5 kOhm. -------------------------------------------------------------------------- The weight of each transformer is 1,4 kg. The total weight incl. package is ca. 4 kg Shipping is possible as a DHL Standard packet up to 5 kg. Deutschland: 7€ EU: 18€ Worldwide: 32€ - 47€ depending on For example a schematic diagram of AD1/ ED Single End - 5 Watt amplifier: Do not hesitate to send questions to my post box:

Pair Siemens Klangfilm 20cm speaker full range w. transformer vintage driver Click images to enlarge Description Pair Fullrange Permadyn 4 OHM speakers( 4.1/4.2 Ohm DC 7 matchewd pair )  made by Siemens  West-germany in the 1960ies ;  fullrange speaker size : 20 cm = 8    with center wizzer, no additonal tweeter necessary . great sounding and performance with original matched ouput transformers rare to find these days as most of them are used in audiophile audio  systems all over the world today. perfect match with any low power single ended tube amps.  price is for the pair, worldwide shipping, all payments Track Page Views WithAuctivas Counter

For sale is a matched pair of the very rare and highly wanted vintage output transformers type BV 7105/2. These transformers are interleaved - both secondary coils are connected parallelly already. This connection makes the frequency response from 30 Hz to 18 kHz.These output transformers are perfect applicable for SE power stages with aAD1, ED, RE604, EL12, AL5/EL5, F2a11, or other tubes, with output impedance in the area between 2,2 kOhm to 5 kOhm. The max. power capacity is ca. 8-10 Watt and the ratio is 1:18. With the ratio about 1:18 these output transformers are suitable for following application: For Example: AD1/ ED Single End - 5 Watt, (U supply 300V, Ua 250 V, Grid -45 V,cathode resistor 750 Ohm) Ra 2,3 kOhm - usable output impedance 6-8 Ohm respectively with RE604 with changing the cathode resistor of 1000 Ohm RE 604 Single End - 2-3 Watt (U supply 300V, Ua 250 V, Grid -45V, cathode resistor 1000 Ohm) Ra 3,5 - 3,8 kOhm - usable output impedance 8-12 OhmOther solution with the BV 7105: EL12 / EL6 Single End - 8,2 Watt (Ua 250 V, Screen 250 V, Grid -7 V) Ra 4 - 5 kOhm - output impedance 12-15 Ohm (this was the original application) EL5 / AL5 Single End - 8,5 Watt (Ua 250V, Screen 275 V, Grid -14 V) Ra 4 - 5 kOhm - output impedance 12-15 Ohm F2A / F2a11 Single End - 10 Watt, (Ua 250 V, Screen 250 V, Grid -7 V- as in Klangfilm Kl. V204) Ra 2,2 - 2,4 kOhm - usable output impedance 6-8 Ohm The normal output transformers constructed for PP power stages, and as well so called match transformers for adaptation of low impedance speakers for high impedance amplifier outputs, are not suitable for using with a SE power stage!! The iron core for OPT in a SE power stage must be assembled with so called magnet slit For creation of a magnet slit all iron sheets must be interposed in one direction only. Therefore the BV 7105 are perfectly suitable for application of the RE604respectively AD1, or for each other power triode or pentode with Ra output resistance about2,2 - 5 kOhm. -------------------------------------------------------------------------- The weight of each transformer is 1,4 kg. The total weight incl. package is ca. 4 kg Shipping is possible as a DHL Standard packet up to 5 kg. Deutschland: 7€ EU: 18€ Worldwide: 32€ - 47€ depending on For example a schematic diagram of AD1/ ED Single End - 5 Watt amplifier: Do not hesitate to send questions to my post box:

For sale is a matched pair of the very rare and highly wanted vintage output transformers type BV 7105/2. These transformers are interleaved - both secondary coils are connected parallelly already. This connection makes the frequency response from 30 Hz to 18 kHz.These output transformers are perfect applicable for SE power stages with aAD1, ED, RE604, EL12, AL5/EL5, F2a11, or other tubes, with output impedance in the area between 2,2 kOhm to 5 kOhm. The max. power capacity is ca. 8-10 Watt and the ratio is 1:18. With the ratio about 1:18 these output transformers are suitable for following application: For Example: AD1/ ED Single End - 5 Watt, (U supply 300V, Ua 250 V, Grid -45 V,cathode resistor 750 Ohm) Ra 2,3 kOhm - usable output impedance 6-8 Ohm respectively with RE604 with changing the cathode resistor of 1000 Ohm RE 604 Single End - 2-3 Watt (U supply 300V, Ua 250 V, Grid -45V, cathode resistor 1000 Ohm) Ra 3,5 - 3,8 kOhm - usable output impedance 8-12 OhmOther solution with the BV 7105: EL12 / EL6 Single End - 8,2 Watt (Ua 250 V, Screen 250 V, Grid -7 V) Ra 4 - 5 kOhm - output impedance 12-15 Ohm (this was the original application) EL5 / AL5 Single End - 8,5 Watt (Ua 250V, Screen 275 V, Grid -14 V) Ra 4 - 5 kOhm - output impedance 12-15 Ohm F2A / F2a11 Single End - 10 Watt, (Ua 250 V, Screen 250 V, Grid -7 V- as in Klangfilm Kl. V204) Ra 2,2 - 2,4 kOhm - usable output impedance 6-8 Ohm The normal output transformers constructed for PP power stages, and as well so called match transformers for adaptation of low impedance speakers for high impedance amplifier outputs, are not suitable for using with a SE power stage!! The iron core for OPT in a SE power stage must be assembled with so called magnet slit For creation of a magnet slit all iron sheets must be interposed in one direction only. Therefore the BV 7105 are perfectly suitable for application of the RE604respectively AD1, or for each other power triode or pentode with Ra output resistance about2,2 - 5 kOhm. -------------------------------------------------------------------------- The weight of each transformer is 1,4 kg. The total weight incl. package is ca. 4 kg Shipping is possible as a DHL Standard packet up to 5 kg. Deutschland: 7€ EU: 18€ Worldwide: 32€ - 47€ depending on For example a schematic diagram of AD1/ ED Single End - 5 Watt amplifier: Do not hesitate to send questions to my post box: