*This listing is fora Completely Overhauled, Burned-In, Tested, and Guaranteed Sansui1000A* Am besten persönlich abholenThis is not the average ebaythis has been serviced job where someone replaced only the clearlydefective capacitors with cheap parts to make it work. Youregetting a restored, completely rebuilt, world-class Sansui1000A!With this unit, I took my timeto test, clean, repair, replace, and upgrade everythingnecessary while using only the most appropriate high quality parts. Theattention to detail here is key. I strove to keep the unitas original as possible, replacing only what is necessary in the audiosections while maintaining original lead dress.While Im not muchfor superlatives, this unit does of course sound very good! Minimal distortion, fast and deep bass (especially with thepresence on), clean midrange, and clear high end. Basicallywhat anyone should expect from a decent piece of tube audio gear.With the exception ofrepair-in-progress photos, I took pains to slightly overexpose the photos tothe point where it shows random dust! I want there to be NO surprises for thenew owner, but do note that most small bits of dust, small defects, etc. cantbe seen under normal lighting conditions. Known IssuesThere are many knownissues concerning any potentially restorable Sansui 1000A. Those issues, aswell as any specific to the unit under repair, MUST be accounted for. The mostprominent include:1. All oil capacitorsmust be replaced. Like all Japanese oil caps of this era, they will be leaky,open, or shorted. 2. All electrolytics must be replaced. This unit was built in1971, and has sat unused for an indeterminate amount of time. Hum and highimpedance in the audio amp are not acceptable, especially given the FARsuperior replacement parts available today. 3. Heat. These units did not provide enough ventilation,especially in the area surrounding the left channel output tubes and powersupply resistors. This commonly leads to output tube and/or transformerfailure. 4. Switches. The rotary wafer switches (Mode, Band Selector,Selector) as well as the front panel rocker switches (Presence, Loudness, etc.)invariably come with a great deal of black oxide on the contacts. This causesproblems due to intermittent or open connections. 5. Output tube bias circuit. Many units come with a biascircuit that does not allow bias adjustment of individual tubes. This isunacceptable in a high-end piece of equipment. 6. No power supply soft-start. The 1000A comes up to over 500Vwithin seconds of turn-on...however the tube cathodes are not warmed up foranother 30 seconds! This causes unnecessary cathode stripping and temporaryvery high voltage on the B+ rail, stressing components. 7. Illumination. Fuse type dial face bulbs andStereo indicator bulbs are frequently burned out, and as theyrequire the disassembly of the faceplate, are difficult to replace. 8. Tubes! Many tubes may be marginal, bad, or simply noisy soall must be tested and auditioned. 9. Solid-state rectifiers. These units use solid staterectifiers from the 1970s which are of very poor quality in comparison toreplacement parts available today. 10. Input/Output connectors. The RCA jacks and speakerconnectors are of dubious quality and always arrive with some sort ofcorrosion, even if its very thin. 11. Flimsy 2-Prong AC cable. Any decent equipment mustinclude a high-quality, properly grounded AC cord. 12. Fuse. This should be replaced with a rating suitable tothe line voltage without taking into account the outlets on the rear whichare frequently left unused. 13. One AC input is 117VAC. There is a selector for input linevoltage, one of which is 117VAC, whereas the line voltage in many countries thehousehold line now averages between 120-130V. Using the unit at these voltages increaseshigh voltage and filament voltage, shortening the life of the tubes. 14. Physical condition. Being a vintage receiver isnt easy!They usually come with some wear and tear, and are many times quite dirty. Repairs and RestorationChassisChassis & knobs cleanedinside and out. Dust, dirt, corrosion, etc. removed.Top cover and base panelre-painted. Both covers were cleaned, primed, paintedwith two coats, then baked in an oven to harden. I used the nearoriginal color on top with flat black on the bottom. If you look at thetop panel with a certain angle on the light you can see deviations from theshape of the metal underneath; these are not normally visible. Bottom panel hasgrommeted bias adjustment access holes drilled, all mounting areas have beencleaned to provide a nice low resistance ground path, and the original mountinghardware has been replaced.Transformer coresrepainted. All three transformers were carefully removed,their bells taken off, windings and leads taped off, and their cores primedthen painted with flat black high heat paint.Faceplate, dial glass, andinside the dial were disassembled, cleaned, andreassembled. The bezel was professionally polished. There are small (basicallyunnoticable) blemishes on the panel and one on the bezel corner which Ihave taken photos of. Dial string was replaced, re-tensioned, and the dialindicator set correctly.New rubber feet installed. I didnot like the other set of hard plastic feet as it allowed the receiver to slidetoo easily and they tended to scratch surfaces!ElectronicsALL low voltage audio signalpath capacitors replaced. Many times overlookedwhen rebuilding these units due to their location/low voltage andtheir not being oil capacitors - theyre old mylar and ceramic! Theseinclude the audio premp input capacitors, audio section of the FMdemultiplexer, and Loudness switch to name a few. Theyare all now polystyrene, polypropylene, silver mica, and PIO (audio preampinput capacitors). ALL Oil capacitors replaced. I installed NOS Aerovox CP04, GudemanXFHS, & Sprague CP08/196P paper in oil (PIO) glass hermetically sealedmil-spec parts. In the chassis pictures, many of these have heat shrink overthem (this is to cover the metal case to avoid possible shorts) or wiressoldered to the case (shorting the case to ground providing shielding andeliminating the possibility of feedback from case). I used theseparts to maintain the vintage tone that is associated with units fromthis era.ALL Electrolytics replaced. MainB+ capacitors are NichiconPW. Secondary B+ capacitors are NichiconCA. Screen decoupling electrolytic replaced with two 47uF in series with 220kequalizing resistors as that is the only part of the power supply that reachesabove 450V during normal or high line conditions (higher voltage rated qualityelectrolytics are no longer available). All other electrolytics arePanasonic EB, ED, or EM. All types are rated at 105C with very low impedanceand all but the PW are rated for at least 10,000Hrs.Fresh heat shrink and nylonbraid around external power resistor wires. Theold braid was cracked and hardened.Audio amplifier hum pots. Theleft and right channel of the audio amplifier have independent DC biasedfilament supplies. Each has a 100 ohm hum adjustment pot, which was adjustedfor lowest output hum.Phono/Mic preamplifier. Theelectrolytics and output coupling capacitors were replaced, but no othermodifications were performed. I used the mic and phono inputs and found thenoise not to be objectionable at all! Judging by the current draw, this couldbe replaced with a simple JFET preamp for lower noise and higher quality, but Ichose not to do this as most of the people I know use separate phono preampsanyhow.Some items disabled. Theseinclude: 1. The 5-pin DIN tape input connector, as these are rarelyused and it would have been more work to re-attach after the RCA inputrebuilds. 2. The speaker phase switch (see below) 3. The headphone jack and speaker on/off switch, as they were poorquality, superfluous functions that relied on a dummy load that wasremoved. This enabled me to add a line filter and IEC socket to the powersupply! ControlsALL pots cleaned with Deoxit. Noisefree is the way to be.Speaker phase switch disabled. Originalswitch contacts were pitted from hot switching, and this seemed only tocause trouble as a high-resistance contact in the speaker circuit. For me,theres plenty of other ways to reverse phase if need be.Speaker impedance switchreplaced. When disassembled, I found the contacts pitted beyond repair. It wasreplaced with a near-identical manufacture switch of the same era that wasdisassembled and had its contacts cleaned and polished before installation.ALL eight front panel rockerswitches and ALL three rotary disassembled and cleaned. Thiswas, without a doubt, the most time-consuming part of the job! With thewafer and rocker switches in the 1000A (and most wafer switches in general!),due to the type of oxidation on the contacts (read: thick, black, sometimesmixed with hardened lubricating grease, and possibly non-conductive)the best method is to clean each contact mechanically with a trusty pencileraser. Even then, some contacts needed to be pre-cleaned with naptha to removesome very thick oxide/grease. All contacts were tested after repair using a4-wire digital ohmmeter to check contact resistance. TubesALL tubes havebeen precision tested. Any tube testingmarginal, bad, or noisy was discarded. Pins have been cleaned on all miniaturetypes. The tubes installed are as follows: Audio 12AX7 preamp tubes replaced with RCA short plate. 6AN8A phase inverter tubes are NOS Motorola branded Tung-Sol 7591A power output tubes replaced with new manufactureTung-Sol. Tuner 6AU6 are original Matsutshita. 6BE6 replaced with NOS RCA. 6AQ8 are original Matsutshita. 6CW4 were replaced with NOS RCA. 6BA6 are original Matsutshita. 6BL8 are original Matsutshita. Upgrades:Adjustments & MeasurementsFilament voltage. Filamentvoltage was measured at the pins during operation and found to be within 2% oflisted value.High voltage. Highvoltage measured at all points in the power supply during operation andfound to be within 5% of listed value (depending on how heavily the outputtubes were biased).Bias and solid state preampvoltage. Measured during operation and found to be within 5% of stated valueon the preamp, with the bias range having an upper end at approx -27V.Output tube bias. Outputtube bias was set initially, then after a week of listening adjustedto final resting point of 35mA +/-100uA per tube at 117VAC line. If youplan to operate this unit at nominal 120-130VAC line voltage, for longevity ofthe tubes I strongly suggest using a line voltage adjustment transformer todrop the incoming line voltage.Resistor values. One3k in the feedback loop was out of tolerance, so I replaced the 3k feedbackloop and the 3k & 5k L+R summing resistors in both the leftand right channel for symmetry using Dale RN60 metal film resistors.Resistor values were tested before installation to within 0.2%. Allothers were found to be within +/-5% of stated value.Tuner. AM/FMtuner and demiltiplexer was checked for proper operation and adjusted wherenecessary.Burn-in. Thisunit has been my main workshop amplifier for over a month. This allowed timefor all of the parts to stabilize and any defects to make themselves known.BiasOutput tube bias circuitcompletely rebuilt. It now has four easilyaccessable adjustments for each output tube. I installed a schottky rectifierfor low noise, Panasonic EB long-life capacitos, Dale RN60 mil-spec metal filmresistors, and Dale mil-spec 10-Turn wirewound miniature trimmers for precisionadjustment. This is mounted and assembled point-to-point on FR-4 material.Bias tubes without removingbottom cover! Gold pin-probe sockets installed nextto tubes so you can make plate current measurements using only a voltmeter.Between each probe socket is a precision 1 ohm, 0.1% non-inductivewirewound plate current sense resistor for absolute accuracy. Grommeted accessholes on the bottom of the amp allow for flathead adjustment ofindividual tube bias current. Tubes and their corresponding adjustment holesare all labeled.[Biasing should only be performed by a qualified technician asthe pin probe sockets can have up to 500VDC present!] ConnectorsALL RCA connectors replacedwith quality gold connectors. This was NOT an easy jobto do well, but I think it is well worth it! Original RCA connectors werecarefully removed. Then the RCA holes in the phenolic were reamed slightlylarger to accomodate the new connectors. Next, the opening in the chassis waswidened slightly so the new ground terminals would not contact the chassis (thetool did slip twice, but it is not noticable). They were then installed,rewired, and continuity checked.Repaced speaker terminals withmodern connectors. Same method used as with theRCA jacks. New terminals are suitable for use with wire, spades, and bananaplugs.Heat IssuesOutput tube heat sinks. Customaluminum finned tube heatsinks have been fabricated and added to theoutput tubes, doubling their average life and removing heat more quickly in theprocess.Input tube shielded heatsinks. Retrofitted with a tube shield base and added very high qualityMil-Spec IERC heat-sinking tube shields. These units typically reduce bulbtemperatures to 115°C for extra long life.Phase inverter heat sinks. The6AN8A gets surprisingly hot. Retrofitted with a tube shield base and addeda custom modified Mil-Spec IERC heat sink type unit. These units remove heatfrom the bulb more effectively than ANY other type of chassis mount tube heatsink or shield, typically acheiving bulb temperatures as low as 104°C. Forreference, a common silver shield will RAISE temperature upwards of180-200°C!DC fans installed. Thesehave been positioned to remove excess heat from the power tube areas first.Powered from the main heater winding, their power circuitry is installedso that NO noise from the fans enter the audio stages. The have their own heavyduty barrel-type power connector (next to the power cable connector). Thisallows for for easy disconnection and removal of the top cover, or todisable them during critical listening as they do make a little noise.Incandecent lamps. Dialillumination lamps and stereo indicator lamps have been replacedwith LEDs so you dont have to replace them again! They look great,eliminates bulb heat contribution, and frees up current on themain heater winding allowing the installation of the DC fans. The tunersensitivity meter and mono indicator lamps were left incandescent -the face plate would look awful with the cold, harsh glow of leds inthese positions!High VoltageHigh voltage power supplyrectifiers replaced. Here Iinstalled Cree silicon carbide schottky rectifiers to eliminateswitching noise. These are miles above the iffy60s/70s rectifiers that comes stock in these receivers.High Voltage time delaycircuit. This circuit uses a heavy-duty 30 second 120VAC time delay relaycoupled with a 120VAC coil 4PDT relay to connect the power transformerhigh voltage secondary directly to the rectifiers, shorting out a high valueresistor. This designhas several advantages: The relay coil and the delay relay heater both operate from the 117V tap on the transformer primary, eliminating any extra load on the power transformer and delivering 117V to the relay coils regardless of the actual line voltage. The 4PDT relay is arranged with three of its 5A contacts in series for higher standoff voltage while switching approx 180V AC. Series connection and AC switching increase lifetime of the relay significantly! The delay relay only controls the relay coil voltage; it should therefor last a lifetime. Both relays are socketed for easy replacement. The two relays are arranged such that when the 4PDT relay turns on, the time delay relay turns off. That means that if the stereo is quickly turned off and on again, the time delay relay will be cool, allowing the time delay function to still operate!AC Power InputComplete EMI/RFI Line Filterwith IEC power plug. Three stageinductive/capacitive design eliminates both common mode and differential modenoise from entering or exiting the line connection! Constructed using 250VACX or Y rated capacitors, 3A rated 100uH and 1.7mH inductors, anda high quality IEC plug, the filter was assembled point to point onFR4 board and rigidly mounted to the chassis both using the IECplug and steel standoffs. The IEC plug was installed so I had to makethe minimum amount of modification to the chassis.The whole line filterassembly is still (relatively) easy to remove for servicing.Fully grounded. 12 gaugesolid copper wire connects directly to the ground terminal of the IEC plug,traverses the line filter, then connects directly to chassis at the center ofthe power supply to serve as a star ground. Safe AND low noise!High quality Power Cord. 14-3shielded mil-spec cable with the shielding terminated to ground only at thehospital grade power plug.New fuse holder & Fuse. Theold fuse holder had a missing cap. The original fuse was sized totake into account the current draw from the AC outlets on the rear which havebeen removed. I will provide one installed and two additional fuses of thecorrect value for the country it is sent to (3.2A, 2.8A, or 1.5A for 100V,110-130V, or 220-240V respectively). Now THAT is arestoration. Enjoy!

This vintage integrated amplifier has been tested and features appear to work other than the power light on the left side of the faceplate. Being that this unit is 50 years old, it is recommended that it would be taken to a service center to evaluate current condition and do any adjustments or refurbishment needed for a reliable and trouble-free device. This is a vintage piece of audio equipment with no warranties expressed or implied. I can send the video verifying its function before it is shipped out. No returns.

The Sansui SP-70 lot is being sold As Is. All items in lot were tested and the only minor issue is the the switches need cleaned. Minor static while selecting high range. One cleaned itself somewhat just by use. On the woofer there are spot on the cone. The pictures show the condition better than I can describe. Please view all pictures to see the overall condition of the speakers and please email any questions. The speakers are being sold As Is. Thank you for looking.

These headphones are simply the nicest looking and fantastic sounding omni-dynamic stereo headphones made in Japan from the mid 70s. Although, they need powerful headphone amp to give their best sound.Vey close to mint condition as you can see on the photos. A real collectors item.Comes with a bonus pair of genuine lamb skin ear pads with memory foam.You can make them attached to the headphones with strong double sided tape if you wish for more comfort then the original donut pads. The SS-100 was Sansuis TOTL headphone in the mid 1970s. It features a full aluminum housing and large orthodynamic drivers designed and built by Fostex. --Driver specifications-- Operating Principle: Planar-magnetic/Orthodynamic Size: 67mm Magnets: Anisotropic ferrite slotted discs Diaphragm material: 6 (?) micron polyester Cord Type Straight, fabric sheathed Ear Coupler Type: Supra-aural Driver Type: Omni-Dynamic (Sansuis term for isodynamic drive) Connector Type: 1/4 TRS Impedance: 75 ohms Sound Pressure Level: 94dB/mW Additional Information Max input: 250mW Additional Information Weight: 430g

Condition DescriptionPlease be sure to read POLICY before purchasing products with [AC100V] in the title or products that use a power outlet. The goods are all in the photograph. Please be sure to check the condition of the product by photos. Questions are always available in the message. ------ Used for daily use. Operation has been checked. Please check the photos for scratches and stains. Please Note shipping from Japan. Please read POLICY before purchasing products with [AC100V] in the title or products that use a power outlet. Policy PaymentPayment is only accepted through payoneer and we can only ship to the address registered with payoneer. Import duties, taxes and fees are not included in the item price or shipping charges. These costs are to be borne by the buyer.Cancellations & ReturnsCancellation or returns will be accepted only if the item has an obvious problem that was not mentioned in the listing description. If that, please let us know within 3 days you got the item. Buyer is responsible for shipping costs and any charge incurred shipping products back.International BuyersCancellations or returns will only be accepted if there is an obvious problem with the items title as well as if there is an obvious problem with the item that was not mentioned in the listing description. If it does, please let us know within 3 days of getting the item. Buyer is responsible for shipping costs and charges will be lost shipping the product back. Always check the voltage before claiming a defect. If you do not check by voltage you will not receive a return. Buyers who refuse to use a transformer will not receive any returns or refunds. Refuse any returns and refunds.[AC 100V] Before you buy the itemAttention Buyers: The voltage for this electronic device is 100V and made for Japan usage ONLY. In order for you to use this device outside Japan where the voltage is higher than 100V such as 200V-240V, you are required to use a transformer to adjust the voltage to your local country. WIthout using a transformer, this device will be broken. We are not responsible for the damage of this device if you use it without a proper transformer. Please purchase it in your local store.Failure to check voltage will void the return.

Sansui QS-100 4 Channel Quadraphonic Decoder and Rear Speaker Amplifier TESTED AND WORKING UNIT IS IN VERY GOOD CONDITION. ALL SALES GUARANTEED TO YOUR SATISFACTION!

Casque haut de gamme vintage Sansui Model SS-100 Headphones Sansui SS-100 très rare et recherché par les collectionneurs tant pour sa rareté que pour ses qualités acoustique se branche sur un ampli,lecteur cd,cd player (amplifier) .Pour la livraison en France par Mondial relay 20 euros,pour la zone Euro 35 euros.Pour le reste des pays hors Europe 50 euros.

Condition Descriptionrelease date 1983 Rated output Effective output: 90W+90W (8?, 10Hz-20kHz, THD 0.003%) playback frequency Frequency response (1W): DC to 300kHz +0 -3dB sensitivity Phono1, 2 MM: 2.5mV/47k?, Phono1, 2 MC: 120?V/3-40?, Tuner, Aux/DA, Tape/PCM play1, 2: 250mV/27k? SNR Phono 1, 2 MM: 88 dB or more, Phono 1, 2 MC: 79 dB or more (120 ?V), Tuner, Aux/DA, Tape/PCM play 1, 2: 110 dB or more Power consumption (W) 220W Features/remarks Integrated amplifier based on the AU-D607F Extra with improvements such as a ground floating circuit * There are many scratches on the exterior. Please check the image. There is a gap for Vol. knob replacement. Please be sure to read POLICY before purchasing products with [AC100V] in the title or products that use a power outlet. The goods are all in the photograph. Please be sure to check the condition of the product by photos. Questions are always available in the message. Please Note shipping from Japan. Please read POLICY before purchasing products with [AC100V] in the title or products that use a power outlet. Policy PaymentPayment is only accepted through payoneer and we can only ship to the address registered with payoneer. Import duties, taxes and fees are not included in the item price or shipping charges. These costs are to be borne by the buyer.Cancellations & ReturnsCancellation or returns will be accepted only if the item has an obvious problem that was not mentioned in the listing description. If that, please let us know within 3 days you got the item. Buyer is responsible for shipping costs and any charge incurred shipping products back.International BuyersCancellations or returns will only be accepted if there is an obvious problem with the items title as well as if there is an obvious problem with the item that was not mentioned in the listing description. If it does, please let us know within 3 days of getting the item. Buyer is responsible for shipping costs and charges will be lost shipping the product back. Always check the voltage before claiming a defect. If you do not check by voltage you will not receive a return. Buyers who refuse to use a transformer will not receive any returns or refunds. Refuse any returns and refunds.[AC 100V] Before you buy the itemAttention Buyers: The voltage for this electronic device is 100V and made for Japan usage ONLY. In order for you to use this device outside Japan where the voltage is higher than 100V such as 200V-240V, you are required to use a transformer to adjust the voltage to your local country. WIthout using a transformer, this device will be broken. We are not responsible for the damage of this device if you use it without a proper transformer. Please purchase it in your local store.Failure to check voltage will void the return.

Sansui T1000 Stereo 16 Station Random Preset. Perfettamente funzionante

Sansui AA-100W sales brochure. This is an original factory released brochure, it is not a copy. 1 page, both printed. In good condition. We will include a stiff cardboard and a Please Do Not Bend sticker to help preserve the integrity of the manual. Shipping to the USA & Canada, please allow a week or so for delivery. Shipping to the UK & Europe, please allow 2-4 weeks or so for delivery. Shipping to all other international locations, please allow 4-6 weeks for delivery.

Sansui PA-100 sales brochure. This is an original factory released brochure, it is not a copy. 1 pages, both sides printed. Shows signs of use, in overall decent used condition. We will include a stiff cardboard and a Please Do Not Bend sticker to help preserve the integrity of the brochure.

Shipping Expedited Shipping (FedEx , DHL) The package will arrive 1-3 days after shipment. (We usually ship out your order within 3-10 working days after receiving your payment.) International Buyers - Please Note: Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying. If there is a remote charge for your address, we will charge you for additional shipping. Thank you for your understanding.

Condition DescriptionPlease be sure to read POLICY before purchasing products with [AC100V] in the title or products that use a power outlet. The goods are all in the photograph. Please be sure to check the condition of the product by photos. Questions are always available in the message. ------ Used for daily use. Operation has been checked. Please check the photos for scratches and stains. Please Note shipping from Japan. Please read POLICY before purchasing products with [AC100V] in the title or products that use a power outlet. Policy PaymentPayment is only accepted through payoneer and we can only ship to the address registered with payoneer. Import duties, taxes and fees are not included in the item price or shipping charges. These costs are to be borne by the buyer.Cancellations & ReturnsCancellation or returns will be accepted only if the item has an obvious problem that was not mentioned in the listing description. If that, please let us know within 3 days you got the item. Buyer is responsible for shipping costs and any charge incurred shipping products back.International BuyersCancellations or returns will only be accepted if there is an obvious problem with the items title as well as if there is an obvious problem with the item that was not mentioned in the listing description. If it does, please let us know within 3 days of getting the item. Buyer is responsible for shipping costs and charges will be lost shipping the product back. Always check the voltage before claiming a defect. If you do not check by voltage you will not receive a return. Buyers who refuse to use a transformer will not receive any returns or refunds. Refuse any returns and refunds.[AC 100V] Before you buy the itemAttention Buyers: The voltage for this electronic device is 100V and made for Japan usage ONLY. In order for you to use this device outside Japan where the voltage is higher than 100V such as 200V-240V, you are required to use a transformer to adjust the voltage to your local country. WIthout using a transformer, this device will be broken. We are not responsible for the damage of this device if you use it without a proper transformer. Please purchase it in your local store.Failure to check voltage will void the return.

Tested working system. Shows Light used Items show normal wear from age/use . please use all photos as guide to condition. I do my best to describe item listed if see any damages other than normal wear. Smoke free & pet free environment. *Batteries Not included if applicable. Most item are not shipped with batteries to save you shipping costs, check listing if otherwise noted if included with your purchase. * Please use Make offer function for all offers or for combine orders Thank you. * Free USA Returns! If item is non working, that states working condition, easy free returns *In order to save waste, we do not include Receipts with purchases if need one please request with order. *We may use CLEAN recycled boxes/packaging. * International Shipping available. If issues with or not showing contact Ebay as I have it set up. Thank you.

Casque haut de gamme vintage Sansui Model SS-100 Headphones Sansui SS-100 très rare et recherché par les collectionneurs tant pour sa rareté que pour ses qualités acoustique se branche sur un ampli,lecteur cd,cd player (amplifier) .Pour la livraison en France par Mondial relay 20 euros,pour la zone Euro 35 euros.Pour le reste des pays hors Europe 50 euros.

Sansui 13 TV VCR Combo Gaming CRT w/ Remote Model: COM3100C Good Condition - Tested / Works - See Video

Condition Descriptionrelease date 1983 Rated output Effective output: 90W+90W (8?, 10Hz-20kHz, THD 0.003%) playback frequency Frequency response (1W): DC to 300kHz +0 -3dB sensitivity Phono1, 2 MM: 2.5mV/47k?, Phono1, 2 MC: 120?V/3-40?, Tuner, Aux/DA, Tape/PCM play1, 2: 250mV/27k? SNR Phono 1, 2 MM: 88 dB or more, Phono 1, 2 MC: 79 dB or more (120 ?V), Tuner, Aux/DA, Tape/PCM play 1, 2: 110 dB or more Power consumption (W) 220W Features/remarks Integrated amplifier based on the AU-D607F Extra with improvements such as a ground floating circuit * There are many scratches on the exterior. Please check the image. There is a gap for Vol. knob replacement. Please be sure to read POLICY before purchasing products with [AC100V] in the title or products that use a power outlet. The goods are all in the photograph. Please be sure to check the condition of the product by photos. Questions are always available in the message. Please Note shipping from Japan. Please read POLICY before purchasing products with [AC100V] in the title or products that use a power outlet. Policy PaymentPayment is only accepted through payoneer and we can only ship to the address registered with payoneer. Import duties, taxes and fees are not included in the item price or shipping charges. These costs are to be borne by the buyer.Cancellations & ReturnsCancellation or returns will be accepted only if the item has an obvious problem that was not mentioned in the listing description. If that, please let us know within 3 days you got the item. Buyer is responsible for shipping costs and any charge incurred shipping products back.International BuyersCancellations or returns will only be accepted if there is an obvious problem with the items title as well as if there is an obvious problem with the item that was not mentioned in the listing description. If it does, please let us know within 3 days of getting the item. Buyer is responsible for shipping costs and charges will be lost shipping the product back. Always check the voltage before claiming a defect. If you do not check by voltage you will not receive a return. Buyers who refuse to use a transformer will not receive any returns or refunds. Refuse any returns and refunds.[AC 100V] Before you buy the itemAttention Buyers: The voltage for this electronic device is 100V and made for Japan usage ONLY. In order for you to use this device outside Japan where the voltage is higher than 100V such as 200V-240V, you are required to use a transformer to adjust the voltage to your local country. WIthout using a transformer, this device will be broken. We are not responsible for the damage of this device if you use it without a proper transformer. Please purchase it in your local store.Failure to check voltage will void the return.

This Sansui DVD/VHS combo player is a versatile addition to any home entertainment setup. It is capable of playing both VHS tapes and DVDs, and features MP3 compatibility and progressive scan technology for a clearer picture. The player was manufactured in June 2003 and is in good working order. The VRDVD4100 model is sleek and silver in color, with a range of features including VCR playback and a DVD region code of 3. It was made in Thailand and is a great option for those looking for a reliable and functional player. Buy with confidence knowing that you are getting a quality device that will enhance your home media experience.

Fonctionne cache un peu abimé voir photos

~Vintage~ Sansui 1000X - Stereo Receiver - Cleaned and Tested Excellent Condition-Made In Japan Attention: We Ship UPS, USPS and depending on the item. Please, always view pics closely before bidding ! We are a reputable Stereo Store with 45 years experience. Professionally Serviced, Cleaned and Tested by our Technicians. All items are shipped fully Insured. World Class packaging guaranteed to arrive as shown in the pictures. Lower 48 States only Please. Normal 0 false false false EN-US X-NONE X-NONE

Sansui COM3100D 13 Combo TV VHS VCR Tested Gaming CRT With Remote. *Works * Has Remote

Sansui T-1000 Quartz Synthesizer FM Stereo/AM Tuner Untested AS-IS. This item has NOT been tested but turns on an lights up. This is being sold AS-IS.

Sansui QS-100 4 Channel Quadraphonic Decoder and Rear Speaker Amplifier TESTED AND WORKING UNIT IS IN VERY GOOD CONDITION. ALL SALES GUARANTEED TO YOUR SATISFACTION!