Description
This is the Sansui AU-D607F, it has been confirmed power on no other testing has been done this auction starts off with the price that I believe will cover all shipping in the United States, no matter where it is, with a couple bucks added on and goes from there. Amplifier will be packed well. The MM/M input of the AU-D607F is switched by the gain and input impedance switch of the equalizer, so that even when the MC cartridge is used, the configuration is ICL and OCL. In addition, MM/MC can be switched with the switch on the front panel, and the current position is indicated by the lighting of the indicator. The power supply section is a two independent power supply system with a 32,800 ? F custom capacitor. It is equipped with a simple tone control circuit composed of CR. Because it is a simple system without an equalizer or power amplifier, it is designed so that the tone control does not work at the volume position of -6dB to 0 db (at full power). Therefore, the saturation does not exceed the amplification of the amplifier at full power unlike the conventional system. Equipped with a subsonic filter, 2-circuit tape monitor, recording selector / copy function, audio muting, balance control, input selector with encoder, etc. There were 2 kinds, black model with Rosewood style bonnet and silver model with white oak style bonnet. TypeIntegrated amplifier Power Amplifier Unit Effective power75W + 75W (8 ohm, 10 hz to 20 khz, THD 0.005%) 75W + 75W (8 ohm, 1 kz, 0.003% THD) Total harmonic distortion factor (10 Hz to 20 kHz at effective output)Not more than 0.005% Intermodulation Distortion Factor (60 Hz : 7 kHz = 4 : 1, SMPTE)Not more than 0.008% Output Bandwidth (IHF, both channel operation, THD 0.02%)5 Hz to 70 kHz Damping factor (new IHF, 20 Hz to 20 kHz)100 (8 ?) Frequency Response (1W)DC ~ 300 khz + 0 -3dB Signal-to-noise ratio (A network)110 dB or more Envelope distortionBelow the measurement limit TIM Strain (Sawtooth method)Below the measurement limit Slew rate± 180 v / ? sec (8 ?) Inside slew rate± 300 v / ? sec (8 ?) Rise time0.8 ? sec Preamplifier Section Input Sensitivity / Input Impedance (1 kHz) Phono1, 2 mm : 2.5mV/47k ? Phono1 MC : 250 ? V/100 ? Tuner, AUX, Tape Play1, 2 : 250mV/27k ? Phono maximum allowable input (1 kHz, THD 0.01%)MM:200mV MC:20mV Output Level / Impedance (1 kHz)Tape Rec : 250 mv (47k ?) / 600 ? Total harmonic distortion factorPhono1, 2 mm : 0.005% or less (20 Hz to 20 kHz, 5 V) RIAA Deviation (MM)20 Hz to 20 kHz ± 0.2 dB Signal-to-noise ratio (A network)Phono1, 2 mm : 88 dB or more Phono1 MC : 70 dB or more Phono input equivalent noise (A network, short circuit) Phono1, 2 mm : -140dBV Phono1 MC:-142dBV Channel separationPhono1, 2 mm : 60 dB or more Phono1 MC : 50 dB or more Tuner, AUX, Tape Play : 80 dB or higher Tone controlBass : + 6 to -8dB at 50 Hz Treble : ± 6 dB at 10 kHz FilterLow : 16 Hz (-3dB, 6dB/oct.) Audio Muting-20dB Rated power consumption (Electrical Appliance and Material Control Law)200W External dimensionsWidth 445x Height 163x Depth 403 mm Weight12.4kg
Live search