One pair of Polk RT1000p speaker grills. These were pulled off my personal speakers and they are in great shape, no damage to note. From a smoke free, pet free home!

Every function has been confirmed 100% working. All speakers drive and sound like new. All of the speakers themselves are in excellent condition. Cosmetic Condition: OK (the veneer is peeling in places on the base and sides).Functional Condition: Very Good. Boasting a sleek, slim silhouette, the Polk RT1000i brings deep precise bass, impressive performance, and unobtrusive, elegant design to any room. Each tower houses a built-in subwoofer (driven by a high-current 35-watt RMS amplifier), so you can enjoy home theater thrills and resounding music without losing valuable floor space to a separate powered subwoofer!The RT1000i towers showcase the exclusive speaker technologies that have made Polk famous. Polks best 1 trilaminate dome tweeter produces smooth, transparent high-frequency detail. A 6-1/2 Dynamic Balance® driver handles the midrange and upper bass frequencies with sheer precision. Another 6-1/2 subwoofer driver within a High Velocity Compression Drive bandpass enclosure joins with Polks Power Port system to deliver spectacular bass response. Speed Matching technology blends the midrange and bass sections seamlessly, for effortless realism in music and movie soundtracks.Polks built-in high-current amplification for the subwoofer not only provides superior bass response, but also increases dynamic range and lowers distortion by reducing the load on your receivers amp. An independent subwoofer volume control on each tower lets you dial in the right amount of bass to match your room and preference. Finished in real black oak wood veneer.Recommended center channel speaker: Polk CS400i.Recommended surround speakers: Polk f/x 500i.Details:video-shieldedfrequency response 36-25,000 Hz (-3dB)8-ohm impedancesensitivity 90 dBhandles 250 watts35-watt RMS subwoofer amp with auto on/off per enclosurereal wood veneertextured front panel43-1/2H x 8W x 13-5/8D Features & specsGeneralEnclosureBass ReflexFinishWood VeneerColorBlackTweeterDomeTweeter Size (inches)1Midrange Size (inches)6.5Woofer Size (inches)6.5Woofer CompositionPolyWoofer SurroundRubberBuilt-in Powered Sub---Dolby Atmos DriversConnector Type5-way post SpecificationsPower Range30-250Frequency Response36-25k HzSensitivity90 dBImpedance (Ohms)8Subwoofer Amp Power35FeaturesDynamic Balance: Dynamic Balance drivers are used for wide, smooth response and low distortion.High Velocity Compression Drive: The High Velocity Compression Drive is a patented subwoofer technology that employs magnetically powerful, high mass drive systems in special band pass enclosures to produce greater output with higher efficiency.Internal 6-1/2 Powered Sub: The internal Dynamic Balance 6-1/2 subwoofer is powered by a built-in 35 watt amplifier. There is an independent subwoofer volume control on the back panel of the speaker, along with the amp line level input and output.Blue Composite Midrange: The speaker uses a blue composite Dynamic Balance mid-bass woofer for clear, accurate midrange.Surrounds: For a smoother response and improved durability, the woofer and midrange use rubber surrounds.Tri-Laminate Tweeters: The improved Dynamic Balance Tri-Laminate tweeter has vapor deposited micro-layers of stainless steel and aluminum for clear, detailed highs.Speed Matching: Speed matching technology matches the start and decay rates of the mid/high frequency array with the subwoofer output. This results in seamless blending with precise attack, speed, and dynamic contrast.Power Port Technology: There is a downward firing port tube opening on the bottom of each speaker which is directed to a funnel-shaped power port. This venting system allows air velocity to slow gradually, vastly reducing air turbulence, and delivering greater bass efficiency than conventional ports.Pedestal: These speakers include an attached pedestal. The power port fires down onto this pedestal helping to provide deep, evenly distributed bass. There is a female thread in each bottom corner of the of the pedestal into which the speaker spikes screw. The spikes have rubber feet attached. The rubber feet may be pulled off the spikes when the speakers are being set on a carpeted floor.Auto On/Off Circuit: The auto on/off circuit turns the power amp on when a signal is sensed and turns the amplifier off a few minutes after signal is no longer received. The power switch is a two-position (auto/off) switch, that allows you to turn the subwoofer completely off or leave it in auto on/off mode.5-way Binding Posts: There are two pairs of gold plated 5-way binding posts connected by gold-plated jumpers. One pair is for the midrange and tweeter. The other pair is for the subwoofer amplifier. These speakers may be wired in two different ways:One option is to leave the terminal jumpers in place and connect speaker wires to one set of posts to deliver speaker level signal to the midrange, tweeter and sub amplifier.The second method involves removing the terminal jumpers and connecting the speaker outputs of the receiver/amplifier to the top set of posts while feeding the subwoofer amplifier with a line level signal from a preamp output (if preamp outputs are available).Power LED: There is a small green power LED located between the two grilles.Carpet Spikes: The speaker height listed in the dimensions includes spikes with rubber feet installed. Removing the rubber feet from the spikes reduces the height to 43.389. Without using the spikes the height is 42.375.NoteFrequency Response: The overall frequency response is 25Hz-26kHz, -3dB frequency response is 36-25kHz. Matching Center Channel (CS400i) and Surrounds (f/x300i in white) available alsoIncludes Carpet Spikes and Manuals - DOES NOT include the Bezels/Grills

Every function has been confirmed 100% working. All speakers drive and sound like new. All of the speakers themselves are in excellent condition. Cosmetic Condition: OK (the veneer is peeling in places on the base and sides).Functional Condition: Very Good. Boasting a sleek, slim silhouette, the Polk RT1000i brings deep precise bass, impressive performance, and unobtrusive, elegant design to any room. Each tower houses a built-in subwoofer (driven by a high-current 35-watt RMS amplifier), so you can enjoy home theater thrills and resounding music without losing valuable floor space to a separate powered subwoofer!The RT1000i towers showcase the exclusive speaker technologies that have made Polk famous. Polks best 1 trilaminate dome tweeter produces smooth, transparent high-frequency detail. A 6-1/2 Dynamic Balance® driver handles the midrange and upper bass frequencies with sheer precision. Another 6-1/2 subwoofer driver within a High Velocity Compression Drive bandpass enclosure joins with Polks Power Port system to deliver spectacular bass response. Speed Matching technology blends the midrange and bass sections seamlessly, for effortless realism in music and movie soundtracks.Polks built-in high-current amplification for the subwoofer not only provides superior bass response, but also increases dynamic range and lowers distortion by reducing the load on your receivers amp. An independent subwoofer volume control on each tower lets you dial in the right amount of bass to match your room and preference. Finished in real black oak wood veneer.Recommended center channel speaker: Polk CS400i.Recommended surround speakers: Polk f/x 500i.Details:video-shieldedfrequency response 36-25,000 Hz (-3dB)8-ohm impedancesensitivity 90 dBhandles 250 watts35-watt RMS subwoofer amp with auto on/off per enclosurereal wood veneertextured front panel43-1/2H x 8W x 13-5/8D Features & specsGeneralEnclosureBass ReflexFinishWood VeneerColorBlackTweeterDomeTweeter Size (inches)1Midrange Size (inches)6.5Woofer Size (inches)6.5Woofer CompositionPolyWoofer SurroundRubberBuilt-in Powered Sub---Dolby Atmos DriversConnector Type5-way post SpecificationsPower Range30-250Frequency Response36-25k HzSensitivity90 dBImpedance (Ohms)8Subwoofer Amp Power35FeaturesDynamic Balance: Dynamic Balance drivers are used for wide, smooth response and low distortion.High Velocity Compression Drive: The High Velocity Compression Drive is a patented subwoofer technology that employs magnetically powerful, high mass drive systems in special band pass enclosures to produce greater output with higher efficiency.Internal 6-1/2 Powered Sub: The internal Dynamic Balance 6-1/2 subwoofer is powered by a built-in 35 watt amplifier. There is an independent subwoofer volume control on the back panel of the speaker, along with the amp line level input and output.Blue Composite Midrange: The speaker uses a blue composite Dynamic Balance mid-bass woofer for clear, accurate midrange.Surrounds: For a smoother response and improved durability, the woofer and midrange use rubber surrounds.Tri-Laminate Tweeters: The improved Dynamic Balance Tri-Laminate tweeter has vapor deposited micro-layers of stainless steel and aluminum for clear, detailed highs.Speed Matching: Speed matching technology matches the start and decay rates of the mid/high frequency array with the subwoofer output. This results in seamless blending with precise attack, speed, and dynamic contrast.Power Port Technology: There is a downward firing port tube opening on the bottom of each speaker which is directed to a funnel-shaped power port. This venting system allows air velocity to slow gradually, vastly reducing air turbulence, and delivering greater bass efficiency than conventional ports.Pedestal: These speakers include an attached pedestal. The power port fires down onto this pedestal helping to provide deep, evenly distributed bass. There is a female thread in each bottom corner of the of the pedestal into which the speaker spikes screw. The spikes have rubber feet attached. The rubber feet may be pulled off the spikes when the speakers are being set on a carpeted floor.Auto On/Off Circuit: The auto on/off circuit turns the power amp on when a signal is sensed and turns the amplifier off a few minutes after signal is no longer received. The power switch is a two-position (auto/off) switch, that allows you to turn the subwoofer completely off or leave it in auto on/off mode.5-way Binding Posts: There are two pairs of gold plated 5-way binding posts connected by gold-plated jumpers. One pair is for the midrange and tweeter. The other pair is for the subwoofer amplifier. These speakers may be wired in two different ways:One option is to leave the terminal jumpers in place and connect speaker wires to one set of posts to deliver speaker level signal to the midrange, tweeter and sub amplifier.The second method involves removing the terminal jumpers and connecting the speaker outputs of the receiver/amplifier to the top set of posts while feeding the subwoofer amplifier with a line level signal from a preamp output (if preamp outputs are available).Power LED: There is a small green power LED located between the two grilles.Carpet Spikes: The speaker height listed in the dimensions includes spikes with rubber feet installed. Removing the rubber feet from the spikes reduces the height to 43.389. Without using the spikes the height is 42.375.NoteFrequency Response: The overall frequency response is 25Hz-26kHz, -3dB frequency response is 36-25kHz. Matching Center Channel (CS400i) and Surrounds (f/x300i in white) available alsoIncludes Carpet Spikes and Manuals - DOES NOT include the Bezels/Grills

For sale is a Polk Audio RT1000P DYNAMIC BALANCED DOME TWEETER SL6502. This is in good Condition and works and sounds great It was removed from a working speaker cabinet, Comes as you see tweeter only not the bezel unless you let me know you need it. Fully tested No Hum or distortion. I do take pride in packing and I will pack with great care at no extra charge, poly bags, foam shims, Bubble wrap etc. I prefer paypal, cashier ck, payment within 3 days after sale. Please buy with confidence see my feedbacks, Sold as is but not DOA thanks for looking, Chris Track Page Views With Auctivas Counter

Polk Audio MW7011 Woofer RT-1000P, 800, 600 Powered from Tower Speaker Excellent EXCELLENT CLEAN & READY TO USE CONDITION! Tested: All functions work properly, as it should. Cosmetically: There are very light scratches, scuffs and normal wear. Please see the detailed pictures. You wont be disappointed. *THIS ITEM IS PRE-OWNED ~ Being Sold ~ As it is described and pictured ~ INCLUDED: All items pictured in this listing.  NOT INCLUDED: Any related items not pictured in this listing.  The Item in this listing has been thoroughly cleaned so you can feel comfortable just opening and using on arrival.Its already bagged and packed with padding to prevent any dust or damage in storage.    If you have any questions, concerns or if extra photos are needed please feel free to contact us, before any bids, offers or purchases are made. We will respond as quickly as possible.    All Items are METICULOUSLY packed to insure you receive it in the exact condition seen in the pictures.                                     ??SUPER FAST SHIPPING??       ?????????????????????????????????? ???????????????????????????????????????????????? WE ALWAYS STRIVE TO SHIP THE SAME OR NEXT BUSINESS DAY                 Thank you for looking and have an AWESOME DAY!

Polk Audio CS400i / CSi40 / RT 35 / RT1000i Replacement Speaker Woofer - MW7011. Used in good working conditions.

The listing includes one Polk MW7011 woofer, one SL6502 Tweeter, the face plate, and 6 original screws. These are working pulls from my personal speakers. I purchased them new at Circuit City in 2000. These make great sounding speakers! From a smoke free, pet free home!

1 Polk Audio Tweeter SL6502 + Housing RT1000P tested and working will be well packed and insured.

2) TWO Polk Audio Speaker Face Plates + Screws For RT SERIES - RT1000P - PART. These are the face plates for the Polk RT-1000P power tower speakers. Great for project or restore. Sold as is buyer pays the shipping

The listing is for two plate amplifiers out of a pair of Polk RT1000p speakers. Sold FOR PARTS OR REPAIR! These were pulled from my personal speakers. I purchased them new at Circuit City in 2000. One of the amps was working, and one wasnt working. Unfortunately I didnt mark which was which. Both are still being sold for PARTS OR REPAIR, becuase they are 24 years old and no idea how much longer the good amp will last. Most of the time the issue is a burned out resistor and some dried out capacitors. I think its pretty cheap to do a DIY repair, or there are shops that repair them. These would be perfect for a repair shop that frequently repairs these, because you would then have cores to repair in advance and just swap when bad ones come in. From a smoke free, pet free home!

Every function has been confirmed 100% working. All speakers drive and sound like new. All of the speakers themselves are in excellent condition. Cosmetic Condition: OK (the veneer is peeling in places on the base and sides).Functional Condition: Very Good. Boasting a sleek, slim silhouette, the Polk RT1000i brings deep precise bass, impressive performance, and unobtrusive, elegant design to any room. Each tower houses a built-in subwoofer (driven by a high-current 35-watt RMS amplifier), so you can enjoy home theater thrills and resounding music without losing valuable floor space to a separate powered subwoofer!The RT1000i towers showcase the exclusive speaker technologies that have made Polk famous. Polks best 1 trilaminate dome tweeter produces smooth, transparent high-frequency detail. A 6-1/2 Dynamic Balance® driver handles the midrange and upper bass frequencies with sheer precision. Another 6-1/2 subwoofer driver within a High Velocity Compression Drive bandpass enclosure joins with Polks Power Port system to deliver spectacular bass response. Speed Matching technology blends the midrange and bass sections seamlessly, for effortless realism in music and movie soundtracks.Polks built-in high-current amplification for the subwoofer not only provides superior bass response, but also increases dynamic range and lowers distortion by reducing the load on your receivers amp. An independent subwoofer volume control on each tower lets you dial in the right amount of bass to match your room and preference. Finished in real black oak wood veneer.Recommended center channel speaker: Polk CS400i.Recommended surround speakers: Polk f/x 500i.Details:video-shieldedfrequency response 36-25,000 Hz (-3dB)8-ohm impedancesensitivity 90 dBhandles 250 watts35-watt RMS subwoofer amp with auto on/off per enclosurereal wood veneertextured front panel43-1/2H x 8W x 13-5/8D Features & specsGeneralEnclosureBass ReflexFinishWood VeneerColorBlackTweeterDomeTweeter Size (inches)1Midrange Size (inches)6.5Woofer Size (inches)6.5Woofer CompositionPolyWoofer SurroundRubberBuilt-in Powered Sub---Dolby Atmos DriversConnector Type5-way post SpecificationsPower Range30-250Frequency Response36-25k HzSensitivity90 dBImpedance (Ohms)8Subwoofer Amp Power35FeaturesDynamic Balance: Dynamic Balance drivers are used for wide, smooth response and low distortion.High Velocity Compression Drive: The High Velocity Compression Drive is a patented subwoofer technology that employs magnetically powerful, high mass drive systems in special band pass enclosures to produce greater output with higher efficiency.Internal 6-1/2 Powered Sub: The internal Dynamic Balance 6-1/2 subwoofer is powered by a built-in 35 watt amplifier. There is an independent subwoofer volume control on the back panel of the speaker, along with the amp line level input and output.Blue Composite Midrange: The speaker uses a blue composite Dynamic Balance mid-bass woofer for clear, accurate midrange.Surrounds: For a smoother response and improved durability, the woofer and midrange use rubber surrounds.Tri-Laminate Tweeters: The improved Dynamic Balance Tri-Laminate tweeter has vapor deposited micro-layers of stainless steel and aluminum for clear, detailed highs.Speed Matching: Speed matching technology matches the start and decay rates of the mid/high frequency array with the subwoofer output. This results in seamless blending with precise attack, speed, and dynamic contrast.Power Port Technology: There is a downward firing port tube opening on the bottom of each speaker which is directed to a funnel-shaped power port. This venting system allows air velocity to slow gradually, vastly reducing air turbulence, and delivering greater bass efficiency than conventional ports.Pedestal: These speakers include an attached pedestal. The power port fires down onto this pedestal helping to provide deep, evenly distributed bass. There is a female thread in each bottom corner of the of the pedestal into which the speaker spikes screw. The spikes have rubber feet attached. The rubber feet may be pulled off the spikes when the speakers are being set on a carpeted floor.Auto On/Off Circuit: The auto on/off circuit turns the power amp on when a signal is sensed and turns the amplifier off a few minutes after signal is no longer received. The power switch is a two-position (auto/off) switch, that allows you to turn the subwoofer completely off or leave it in auto on/off mode.5-way Binding Posts: There are two pairs of gold plated 5-way binding posts connected by gold-plated jumpers. One pair is for the midrange and tweeter. The other pair is for the subwoofer amplifier. These speakers may be wired in two different ways:One option is to leave the terminal jumpers in place and connect speaker wires to one set of posts to deliver speaker level signal to the midrange, tweeter and sub amplifier.The second method involves removing the terminal jumpers and connecting the speaker outputs of the receiver/amplifier to the top set of posts while feeding the subwoofer amplifier with a line level signal from a preamp output (if preamp outputs are available).Power LED: There is a small green power LED located between the two grilles.Carpet Spikes: The speaker height listed in the dimensions includes spikes with rubber feet installed. Removing the rubber feet from the spikes reduces the height to 43.389. Without using the spikes the height is 42.375.NoteFrequency Response: The overall frequency response is 25Hz-26kHz, -3dB frequency response is 36-25kHz. Matching Center Channel (CS400i) and Surrounds (f/x300i in white) available alsoIncludes Carpet Spikes and Manuals - DOES NOT include the Bezels/Grills

Polk Audio RT 1000 Floor Standing Speakers Pair Working Local pickup available. They are working. The wood has some damage. Sold as is . Boasting a sleek, slim silhouette, the Polk RT1000i brings deep precise bass, impressive performance, and unobtrusive, elegant design to any room. Each tower houses a built-in subwoofer (driven by a high-current 35-watt RMS amplifier), so you can enjoy home theater thrills and resounding music without losing valuable floor space to a separate powered subwoofer!The RT1000i towers showcase the exclusive speaker technologies that have made Polk famous. Polks best 1 trilaminate dome tweeter produces smooth, transparent high-frequency detail. A 6-1/2 Dynamic Balance® driver handles the midrange and upper bass frequencies with sheer precision. Another 6-1/2 subwoofer driver within a High Velocity Compression Drive bandpass enclosure joins with Polks Power Port system to deliver spectacular bass response. Speed Matching technology blends the midrange and bass sections seamlessly, for effortless realism in music and movie soundtracks.Polks built-in high-current amplification for the subwoofer not only provides superior bass response, but also increases dynamic range and lowers distortion by reducing the load on your receivers amp. An independent subwoofer volume control on each tower lets you dial in the right amount of bass to match your room and preference. Finished in real black oak wood veneer.Recommended center channel speaker: Polk CS400i.Recommended surround speakers: Polk f/x 500i. Details:video-shieldedfrequency response 36-25,000 Hz (-3dB)8-ohm impedancesensitivity 90 dBhandles 250 watts35-watt RMS subwoofer amp with auto on/off per enclosurereal wood veneertextured front panel43-1/2H x 8W x 13-5/8D

The listing is for two plate amplifiers out of a pair of Polk RT1000p speakers. Sold FOR PARTS OR REPAIR! These were pulled from my personal speakers. I purchased them new at Circuit City in 2000. One of the amps was working, and one wasnt working. Unfortunately I didnt mark which was which. Both are still being sold for PARTS OR REPAIR, becuase they are 24 years old and no idea how much longer the good amp will last. Most of the time the issue is a burned out resistor and some dried out capacitors. I think its pretty cheap to do a DIY repair, or there are shops that repair them. These would be perfect for a repair shop that frequently repairs these, because you would then have cores to repair in advance and just swap when bad ones come in. From a smoke free, pet free home!

Every function has been confirmed 100% working. All speakers drive and sound like new. All of the speakers themselves are in excellent condition. Cosmetic Condition: OK (the veneer is peeling in places on the base and sides).Functional Condition: Very Good. Boasting a sleek, slim silhouette, the Polk RT1000i brings deep precise bass, impressive performance, and unobtrusive, elegant design to any room. Each tower houses a built-in subwoofer (driven by a high-current 35-watt RMS amplifier), so you can enjoy home theater thrills and resounding music without losing valuable floor space to a separate powered subwoofer!The RT1000i towers showcase the exclusive speaker technologies that have made Polk famous. Polks best 1 trilaminate dome tweeter produces smooth, transparent high-frequency detail. A 6-1/2 Dynamic Balance® driver handles the midrange and upper bass frequencies with sheer precision. Another 6-1/2 subwoofer driver within a High Velocity Compression Drive bandpass enclosure joins with Polks Power Port system to deliver spectacular bass response. Speed Matching technology blends the midrange and bass sections seamlessly, for effortless realism in music and movie soundtracks.Polks built-in high-current amplification for the subwoofer not only provides superior bass response, but also increases dynamic range and lowers distortion by reducing the load on your receivers amp. An independent subwoofer volume control on each tower lets you dial in the right amount of bass to match your room and preference. Finished in real black oak wood veneer.Recommended center channel speaker: Polk CS400i.Recommended surround speakers: Polk f/x 500i.Details:video-shieldedfrequency response 36-25,000 Hz (-3dB)8-ohm impedancesensitivity 90 dBhandles 250 watts35-watt RMS subwoofer amp with auto on/off per enclosurereal wood veneertextured front panel43-1/2H x 8W x 13-5/8D Features & specsGeneralEnclosureBass ReflexFinishWood VeneerColorBlackTweeterDomeTweeter Size (inches)1Midrange Size (inches)6.5Woofer Size (inches)6.5Woofer CompositionPolyWoofer SurroundRubberBuilt-in Powered Sub---Dolby Atmos DriversConnector Type5-way post SpecificationsPower Range30-250Frequency Response36-25k HzSensitivity90 dBImpedance (Ohms)8Subwoofer Amp Power35FeaturesDynamic Balance: Dynamic Balance drivers are used for wide, smooth response and low distortion.High Velocity Compression Drive: The High Velocity Compression Drive is a patented subwoofer technology that employs magnetically powerful, high mass drive systems in special band pass enclosures to produce greater output with higher efficiency.Internal 6-1/2 Powered Sub: The internal Dynamic Balance 6-1/2 subwoofer is powered by a built-in 35 watt amplifier. There is an independent subwoofer volume control on the back panel of the speaker, along with the amp line level input and output.Blue Composite Midrange: The speaker uses a blue composite Dynamic Balance mid-bass woofer for clear, accurate midrange.Surrounds: For a smoother response and improved durability, the woofer and midrange use rubber surrounds.Tri-Laminate Tweeters: The improved Dynamic Balance Tri-Laminate tweeter has vapor deposited micro-layers of stainless steel and aluminum for clear, detailed highs.Speed Matching: Speed matching technology matches the start and decay rates of the mid/high frequency array with the subwoofer output. This results in seamless blending with precise attack, speed, and dynamic contrast.Power Port Technology: There is a downward firing port tube opening on the bottom of each speaker which is directed to a funnel-shaped power port. This venting system allows air velocity to slow gradually, vastly reducing air turbulence, and delivering greater bass efficiency than conventional ports.Pedestal: These speakers include an attached pedestal. The power port fires down onto this pedestal helping to provide deep, evenly distributed bass. There is a female thread in each bottom corner of the of the pedestal into which the speaker spikes screw. The spikes have rubber feet attached. The rubber feet may be pulled off the spikes when the speakers are being set on a carpeted floor.Auto On/Off Circuit: The auto on/off circuit turns the power amp on when a signal is sensed and turns the amplifier off a few minutes after signal is no longer received. The power switch is a two-position (auto/off) switch, that allows you to turn the subwoofer completely off or leave it in auto on/off mode.5-way Binding Posts: There are two pairs of gold plated 5-way binding posts connected by gold-plated jumpers. One pair is for the midrange and tweeter. The other pair is for the subwoofer amplifier. These speakers may be wired in two different ways:One option is to leave the terminal jumpers in place and connect speaker wires to one set of posts to deliver speaker level signal to the midrange, tweeter and sub amplifier.The second method involves removing the terminal jumpers and connecting the speaker outputs of the receiver/amplifier to the top set of posts while feeding the subwoofer amplifier with a line level signal from a preamp output (if preamp outputs are available).Power LED: There is a small green power LED located between the two grilles.Carpet Spikes: The speaker height listed in the dimensions includes spikes with rubber feet installed. Removing the rubber feet from the spikes reduces the height to 43.389. Without using the spikes the height is 42.375.NoteFrequency Response: The overall frequency response is 25Hz-26kHz, -3dB frequency response is 36-25kHz. Matching Center Channel (CS400i) and Surrounds (f/x300i in white) available alsoIncludes Carpet Spikes and Manuals - DOES NOT include the Bezels/Grills

Polk Audio RT 1000 Floor Standing Speakers Pair Working Local pickup available. They are working. The wood has some damage. Sold as is . Boasting a sleek, slim silhouette, the Polk RT1000i brings deep precise bass, impressive performance, and unobtrusive, elegant design to any room. Each tower houses a built-in subwoofer (driven by a high-current 35-watt RMS amplifier), so you can enjoy home theater thrills and resounding music without losing valuable floor space to a separate powered subwoofer!The RT1000i towers showcase the exclusive speaker technologies that have made Polk famous. Polks best 1 trilaminate dome tweeter produces smooth, transparent high-frequency detail. A 6-1/2 Dynamic Balance® driver handles the midrange and upper bass frequencies with sheer precision. Another 6-1/2 subwoofer driver within a High Velocity Compression Drive bandpass enclosure joins with Polks Power Port system to deliver spectacular bass response. Speed Matching technology blends the midrange and bass sections seamlessly, for effortless realism in music and movie soundtracks.Polks built-in high-current amplification for the subwoofer not only provides superior bass response, but also increases dynamic range and lowers distortion by reducing the load on your receivers amp. An independent subwoofer volume control on each tower lets you dial in the right amount of bass to match your room and preference. Finished in real black oak wood veneer.Recommended center channel speaker: Polk CS400i.Recommended surround speakers: Polk f/x 500i. Details:video-shieldedfrequency response 36-25,000 Hz (-3dB)8-ohm impedancesensitivity 90 dBhandles 250 watts35-watt RMS subwoofer amp with auto on/off per enclosurereal wood veneertextured front panel43-1/2H x 8W x 13-5/8D

One pair of Polk RT1000p speaker grills. These were pulled off my personal speakers and they are in great shape, no damage to note. From a smoke free, pet free home!

All the speakers are in great working condition. I will take plenty of pictures due to the weight of the system they would be pick up only. This is what is included One PSW 650 powered subwoofer, which is in black Two RT 3000 P which are a tall 30 inch tall speaker by about 10 wide Two RT 3000 P which are about 18 inches tall and about eight wide two f/z 1000they are the triangle speakers also 18 inches tall about a foot wide in the back and maybe 3 inches wide in the front One 3 foot long about 10 inches tall CS 1000 P

The listing includes one Polk MW7011 woofer, one SL6502 Tweeter, the face plate, and 6 original screws. These are working pulls from my personal speakers. I purchased them new at Circuit City in 2000. These make great sounding speakers! From a smoke free, pet free home!

Polk Audio RT 1000 Floor Standing Speakers Pair Working Local pickup available. They are working. The wood has some damage. Sold as is . Boasting a sleek, slim silhouette, the Polk RT1000i brings deep precise bass, impressive performance, and unobtrusive, elegant design to any room. Each tower houses a built-in subwoofer (driven by a high-current 35-watt RMS amplifier), so you can enjoy home theater thrills and resounding music without losing valuable floor space to a separate powered subwoofer!The RT1000i towers showcase the exclusive speaker technologies that have made Polk famous. Polks best 1 trilaminate dome tweeter produces smooth, transparent high-frequency detail. A 6-1/2 Dynamic Balance® driver handles the midrange and upper bass frequencies with sheer precision. Another 6-1/2 subwoofer driver within a High Velocity Compression Drive bandpass enclosure joins with Polks Power Port system to deliver spectacular bass response. Speed Matching technology blends the midrange and bass sections seamlessly, for effortless realism in music and movie soundtracks.Polks built-in high-current amplification for the subwoofer not only provides superior bass response, but also increases dynamic range and lowers distortion by reducing the load on your receivers amp. An independent subwoofer volume control on each tower lets you dial in the right amount of bass to match your room and preference. Finished in real black oak wood veneer.Recommended center channel speaker: Polk CS400i.Recommended surround speakers: Polk f/x 500i. Details:video-shieldedfrequency response 36-25,000 Hz (-3dB)8-ohm impedancesensitivity 90 dBhandles 250 watts35-watt RMS subwoofer amp with auto on/off per enclosurereal wood veneertextured front panel43-1/2H x 8W x 13-5/8D

Tested

For sale is a Polk Audio RT1000P DYNAMIC BALANCED DOME TWEETER SL6502. This is in good Condition and works and sounds great It was removed from a working speaker cabinet, Comes as you see tweeter only not the bezel unless you let me know you need it. Fully tested No Hum or distortion. I do take pride in packing and I will pack with great care at no extra charge, poly bags, foam shims, Bubble wrap etc. I prefer paypal, cashier ck, payment within 3 days after sale. Please buy with confidence see my feedbacks, Sold as is but not DOA thanks for looking, Chris Track Page Views With Auctivas Counter

Polk Audio RT 1000 Floor Standing Speakers Pair Working Local pickup available. They are working. The wood has some damage. Sold as is . Boasting a sleek, slim silhouette, the Polk RT1000i brings deep precise bass, impressive performance, and unobtrusive, elegant design to any room. Each tower houses a built-in subwoofer (driven by a high-current 35-watt RMS amplifier), so you can enjoy home theater thrills and resounding music without losing valuable floor space to a separate powered subwoofer!The RT1000i towers showcase the exclusive speaker technologies that have made Polk famous. Polks best 1 trilaminate dome tweeter produces smooth, transparent high-frequency detail. A 6-1/2 Dynamic Balance® driver handles the midrange and upper bass frequencies with sheer precision. Another 6-1/2 subwoofer driver within a High Velocity Compression Drive bandpass enclosure joins with Polks Power Port system to deliver spectacular bass response. Speed Matching technology blends the midrange and bass sections seamlessly, for effortless realism in music and movie soundtracks.Polks built-in high-current amplification for the subwoofer not only provides superior bass response, but also increases dynamic range and lowers distortion by reducing the load on your receivers amp. An independent subwoofer volume control on each tower lets you dial in the right amount of bass to match your room and preference. Finished in real black oak wood veneer.Recommended center channel speaker: Polk CS400i.Recommended surround speakers: Polk f/x 500i. Details:video-shieldedfrequency response 36-25,000 Hz (-3dB)8-ohm impedancesensitivity 90 dBhandles 250 watts35-watt RMS subwoofer amp with auto on/off per enclosurereal wood veneertextured front panel43-1/2H x 8W x 13-5/8D

Original Polk audio RT Series RT1000i RT2000i Users Manual as pictured.

Polk Audio RT 1000 Floor Standing Speakers Pair Working Local pickup available. They are working. The wood has some damage. Sold as is . Boasting a sleek, slim silhouette, the Polk RT1000i brings deep precise bass, impressive performance, and unobtrusive, elegant design to any room. Each tower houses a built-in subwoofer (driven by a high-current 35-watt RMS amplifier), so you can enjoy home theater thrills and resounding music without losing valuable floor space to a separate powered subwoofer!The RT1000i towers showcase the exclusive speaker technologies that have made Polk famous. Polks best 1 trilaminate dome tweeter produces smooth, transparent high-frequency detail. A 6-1/2 Dynamic Balance® driver handles the midrange and upper bass frequencies with sheer precision. Another 6-1/2 subwoofer driver within a High Velocity Compression Drive bandpass enclosure joins with Polks Power Port system to deliver spectacular bass response. Speed Matching technology blends the midrange and bass sections seamlessly, for effortless realism in music and movie soundtracks.Polks built-in high-current amplification for the subwoofer not only provides superior bass response, but also increases dynamic range and lowers distortion by reducing the load on your receivers amp. An independent subwoofer volume control on each tower lets you dial in the right amount of bass to match your room and preference. Finished in real black oak wood veneer.Recommended center channel speaker: Polk CS400i.Recommended surround speakers: Polk f/x 500i. Details:video-shieldedfrequency response 36-25,000 Hz (-3dB)8-ohm impedancesensitivity 90 dBhandles 250 watts35-watt RMS subwoofer amp with auto on/off per enclosurereal wood veneertextured front panel43-1/2H x 8W x 13-5/8D