Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

These speakers are in good cosmetic and working condition. They are huge!! Theyre around 5 feet tall and super heavy. It will be local pick up only because of the sizes. They will come with speaker wire for each cabinet and the connector cable. On one of the speakers the side is coming off, I think that happened in transit. Easy repair with some wood glue. Please see photos for more description. Everything in the pictures will be included. Please feel free to ask any questions and throw me an offer.

This remote control is specifically designed for the Polk Audio reference home XM satellite radio tuner. It is compatible with the XRT12 model and is tested to be in good working condition. With this remote, you can easily control your satellite radio and access all of its features effortlessly. The remote is branded with XM and is also compatible with other brands such as Polk Audio. As a radio remote, it falls under the category of TV, video and audio accessories, making it a must-have for anyone who wants to control their satellite radio from a distance. Get this remote control today and enjoy the convenience it brings to your satellite radio listening experience.

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Polk Audio XM Reference XRt12 Tuner XM Satellite Receiver (No remote/No Antenna). Used with a few minor scratches and blemishes from being used and out of packaging, there is a small 1cm surface scratch on the display, but not very noticeable. From a smoking home. Tested and works great. Product highlights:Dedicated home XM tunerBurr-Brown digital-to-analog converterVideo output (composite) sends channel, artist, and song info to your television for easy visibilityOptical and coaxial digital outputsanalog audio output (stereo RCA jacks)4-line blue LCD10-song memory20 channel presetssearch by channel or categorysubscription to XM required (service available anywhere in the lower 48 states — not available in Alaska, Hawaii, or U.S. Territories)17W x 2-3/8H x 12D ****Please note NO remote or antenna included****

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

XM Satellite Radio Reference Tuner Polk Audio XRT12 - No Remote Powers on - no further testing - was removed from working system Has the unit cable for the antenna

With the XRt12, Polk has set the standard for XM home tuners. Not only do its sleek lines and clean design integrate with the other components in your home rack, its unbeatable sound quality lets you experience XM in all its expansive digital glory. One listen, and you'll agree that this is the finest way to enjoy XM at home. Pre-owned in very good condition. Comes with remote. Manual available online.

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

I have for sale (1) Polk Audio XRt12 XM Satellite home tuner. Tested Works flawlessly. (As of now cannot find remote, if that changes i will update listing.) Ships only to lower 48 States.

Very good condition. Was only used a handful of times. Comes basically flawless Comes w remote. Testing and working

This Polk Audio 23TLL SDA speaker offers impressive sound quality that will elevate your listening experience. With its advanced SDA technology, you can enjoy an immersive, room-filling sound that brings your favorite music and movies to life. The speaker is in great working condition and has been thoroughly tested to ensure optimal performance. Featuring the renowned Polk Audio brand, this speaker is perfect for any home audio setup. Its sleek design and powerful sound make it a great addition to your entertainment system. Whether you're watching a movie or listening to music, this speaker will deliver high-quality sound that will impress even the most discerning audiophile. Original owner absolutely no shipping. Absolutely no returns. grills are nice some small cosmetic on the wood but not a big deal!Works 100% with SDA CABLE. copy and paste in google for video! https://youtu.be/XbY5_ndgJ_Q?si=3K0qC4hohDPFPAS0

This Polk Audio XRT12 XM Satellite Radio Reference Tuner is a great addition to your home audio system. Enjoy high quality satellite radio. The tuner is compatible with various brands and unit types, such as Polk Audio, xm, and gal. This item is perfect for those who appreciate quality sound and want to enhance their home audio experience. Tuner has some minor cosmetic wear, but is fully functional; unit only, no remote

Slightly used but in perfect condition from a non smoking home Enhance your home audio experience with these Polk Audio SDA Signature Reference System SRS 2.3 TL speakers. These wired front right and left speakers with rectangular shape are perfect for any room in your house. They are specifically designed for music lovers who appreciate high-quality sound. Pair them with your favorite music player and enjoy the rich, detailed sound that these speakers deliver. These speakers are suitable for those who seek an immersive audio experience.

PolkAudio XM Reference Home Tuner XRt12 Sattelite Radio Black + Radio W/ Remote. Condition is Used. Shipped with USPS Priority Mail.

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

Local pickup only!Cosmetically and functionally in fantastic condition, with no issues. Comes with interconnect cable and speaker cables. These sound wonderful! I no longer need them.One Caveat- I am going to Brooklyn, NY in 2 weeks so I could bring with me and deliver on the way. Will need to discuss!

Get ready to experience exceptional audio quality with these Polk Audio SDA CRS Compact Reference System Speakers. The black bookshelf speakers are designed to impress with their 2.0 channel system configuration and wired connectivity. Featuring Polk Audios signature sound, these compact speakers deliver a powerful performance that will fill any room with rich, clear sound. The SDA CRS Compact model boasts a sleek and elegant design, making it a perfect fit for any home audio setup. With its high-quality features and impressive performance, these speakers are a must-have for any music lover or home entertainment enthusiast. Dont miss out on the opportunity to upgrade your audio experience with these Polk Audio SDA CRS Compact Reference System Speakers.This item is used It has been tested works as is should Remember it is used so it will have some Small scratches THE HOLDERS FOR ONE COVER IS BROKEN PLEASE CHECK THE PICTURESYou Will get everything thats on the pictures Please check all the pictures before purchase Returns are accepted within 30 days of receiving the itemBuyer pays for return If the return was accepted You will ship the item back and you wait till we get the item back and inspect the item before refund. you will get refunded if we get the item in same condition as it was sold.please contact us before leaving a Negative feedback or any problem We will try to help you as soon as we can Contact if you have any question We usually response within12 hoursNo Shipping To Hawai, PR And Alaska

Polk Audio’s three-piece Reference Monitor speaker system, the RM-3000, consists of two small satellite speakers and a subwoofer module. Although this general configuration is currently enjoying increased popularity, Polk’s version differs from the others in many of its design details.Each of the satellite speakers is a miniature two-way system with a 3-1/2-inch “woofer” operating above 200 Hz and crossing over at approximately 4,000 Hz to a 3/4-inch dome tweeter. The tweeter is protected against burnout by an internal auto reset protection device that cuts off its signal until the power has been reduced to a safe level. The tweeter is stepped back about 1-1/4 inches from the plane of the woofer to provide proper time alignment of the outputs of the two drivers.The satellite enclosure is made of a high-density, non-resonant polymer aggregate similar to the material used for high-quality kitchen countertops. The smooth, glassy exterior is resistant to physical damage, and each of the satellites— which measure only 6-3/4 inches high, 4-1/4 inches wide, and 5 inches deep, including the molded plastic grilles—weighs a surprisingly heavy 4-1/2 pounds. The crossovers contain second-order low-pass and high-pass sections designed to complement the time alignment of the drivers. In addition to its crossover network, each satellite also contains a 200-hz high-pass filter that protects it from being damaged by high-level low-frequency signals.The subwoofer contains two 6-1/2-inch cone drivers, each driven by one stereo channel. For each channel, the appropriate satellite, the subwoofer, and the amplifier are simply wired in parallel. The subwoofer enclosure, which measures 20-1/4 inches wide, 13 inches deep, and 10 inches high, is supported 2 inches above the floor on four rubber feet. Its interior is divided into two separate sections o? different volumes, with the drivers mounted on the dividing partition. The rear surfaces of the two driver cones face the sealed volume, which provides the necessary stiffness for their proper operation. In the other section, the pressure generated by the drivers is coupled to a 10-inch passive radiator mounted on the bottom of the cabinet, facing the floor. According to Polk, the passive-radiator coupling reproduces the low frequencies more efficiently than a simple port radiator, while the mass and size of the passive cone (called the “sub-bass” radiator) attenuate the higher frequencies, providing an 18-dB-per-octave rolloff matching the low-frequency rolloff of the satellites. Since each driver is connected to one of the stereo channels, the two channels are acoustically blended throughout the subwoofer’s operating frequency range (which contains virtually no directional information). Although the subwoofer’s response rolls off naturally above 170 Hz, the unit also contains a first-order low-pass filter to avoid wasting amplifier power above its operating range.

For sale today is a Polk XM Reference Tuner, Model XRt12. Tuner is black with gold trim. Tuner powers on and works well. Will ship ground, typically FedEx Home. Should you have any questions, please dont hesitate to contact me. Thanks!

Read (you may need to expand the view) the spec sheet posted as a photo for all the details. These have rarely been used.

Tested and works! Comes with original remote. Please check out our eBay store. We have over 1000+ listing and are adding more daily! Sold as is. Everything you see in the pictures is what is included in this lot. Photos are the best description. Please look at ALL pictures closely before purchasing. We will document any damage the best we can but the photos will always be the best way to exam the item. Items may need a more in depth cleaning. We will do our best to clean every item, although sometimes we can’t do a full thorough clean. Message us for additional photos or questions. We are a large store please allow up to 3 business days for your item to go out. We of course will get them out as fast as we can. If you ever have a concern, PLEASE MESSAGE US before leaving negative feedback. We will help resolve whatever issue you are having. We try very hard to provide good communication and always strive for everyone to have a positive experience!!