Pre-main amplifier with Marantzs separate amplifier technology.The output stage is a triple push-pull configuration using MOS FET.MOS FET has characteristics such as excellent high-frequency characteristics, high withstand voltage and high power can be applied at the same time, because it operates only with majority carriers in principle, high input impedance higher than that of J-FET is realized, and because there is little accumulation effect during switching, turn-off time is extremely shortened and high-speed switching is possible. Together with Marantzs original Quarter A, MOS FET realizes ideal operation.Using a unique Quarter A circuit, it performs full class A operation up to 1/4 of the maximum output and automatically shifts to class AB operation up to the maximum output. This autoshift is controlled by an electronic control. It detects the output voltage of the main amplifier and controls the bias current with a high-speed switching circuit.The detection speed of the PM-94 circuit is higher than that of the conventional Quarter A circuit, enabling smoother control.In order to fully demonstrate the performance of the MC cartridge, two high performance MC transformers are mounted on the MC input independently on the left and right sides.This transformer has a 2-coil configuration and uses double shielding in the core direction and winding direction. It has a quality close to that of the high-sound MC transformer MC1000.The step-up ratio is switchable between High and Low.The power supply section is equipped with a large transformer and a 90,000 ? F large electrolytic capacitor.In particular, toroidal transformers are shielded by three layers of silicon steel plates to prevent flux.Copper-plated steel sheet material Copper-Tight is used throughout the chassis, and the uniform copper-plated finish of Copper-Tight is more effective than conventional copper plating.Thorough tuning has been applied, such as using parts that have been examined through hearing.We have adopted a pair electrolytic capacitor with equivalent characteristics and sound quality, and switches with improved sound quality by copper-plating. In addition, 70-micron thick circuit boards and oxygen-free copper wires are used.AC100V Made In Japan.

Welcome to Audio/Video Archives, the largest home of audio literature available on eBay! This Review is an Reprint Review from 1994. The Picture is of the actual item. It will have a Test of the product, Specs, Commentary and Information about the item listed. It is a beautiful piece of Audio History. I have THOUSANDS more from every major brand of Audio from 1950 up to now. ---Satisfaction is GUARANTEED at AV Archives! Take a look at my feedback for satisfied customers! I have been open since 2007 and have sold THOUSANDS of Ads, Reviews, and Brochures to satisfied customers. ---I Ship Worldwide and combine shipping, each additional item is just $1 after the first is paid. ---Each Page is 8.5 by 11 unless otherwise noted in title. ---Single-Sided professional matte photo pages, unless otherwise noted in the title. ---These Ads and Reviews are perfect for framing and placed in your Audio Room. ---I have a HUGE Vinyl Record Store with Thousands of Collectable records, and MANY First Pressings/Audiophile LPs. Just click on my Vinyl Record Store link on the left under categories. Email me for any specific questions, You will hear back from me usually within 4 hours, THANK YOU! Greg Powered by eBay Turbo ListerThe free listing tool. List your items fast and easy and manage your active items.

Pre-main amplifier with Marantzs separate amplifier technology.The output stage is a triple push-pull configuration using MOS FET.MOS FET has characteristics such as excellent high-frequency characteristics, high withstand voltage and high power can be applied at the same time, because it operates only with majority carriers in principle, high input impedance higher than that of J-FET is realized, and because there is little accumulation effect during switching, turn-off time is extremely shortened and high-speed switching is possible. Together with Marantzs original Quarter A, MOS FET realizes ideal operation.Using a unique Quarter A circuit, it performs full class A operation up to 1/4 of the maximum output and automatically shifts to class AB operation up to the maximum output. This autoshift is controlled by an electronic control. It detects the output voltage of the main amplifier and controls the bias current with a high-speed switching circuit.The detection speed of the PM-94 circuit is higher than that of the conventional Quarter A circuit, enabling smoother control.In order to fully demonstrate the performance of the MC cartridge, two high performance MC transformers are mounted on the MC input independently on the left and right sides.This transformer has a 2-coil configuration and uses double shielding in the core direction and winding direction. It has a quality close to that of the high-sound MC transformer MC1000.The step-up ratio is switchable between High and Low.The power supply section is equipped with a large transformer and a 90,000 ? F large electrolytic capacitor.In particular, toroidal transformers are shielded by three layers of silicon steel plates to prevent flux.Copper-plated steel sheet material Copper-Tight is used throughout the chassis, and the uniform copper-plated finish of Copper-Tight is more effective than conventional copper plating.Thorough tuning has been applied, such as using parts that have been examined through hearing.We have adopted a pair electrolytic capacitor with equivalent characteristics and sound quality, and switches with improved sound quality by copper-plating. In addition, 70-micron thick circuit boards and oxygen-free copper wires are used.AC100V Made In Japan.

Pre-main amplifier with Marantzs separate amplifier technology.The output stage is a triple push-pull configuration using MOS FET.MOS FET has characteristics such as excellent high-frequency characteristics, high withstand voltage and high power can be applied at the same time, because it operates only with majority carriers in principle, high input impedance higher than that of J-FET is realized, and because there is little accumulation effect during switching, turn-off time is extremely shortened and high-speed switching is possible. Together with Marantzs original Quarter A, MOS FET realizes ideal operation.Using a unique Quarter A circuit, it performs full class A operation up to 1/4 of the maximum output and automatically shifts to class AB operation up to the maximum output. This autoshift is controlled by an electronic control. It detects the output voltage of the main amplifier and controls the bias current with a high-speed switching circuit.The detection speed of the PM-94 circuit is higher than that of the conventional Quarter A circuit, enabling smoother control.In order to fully demonstrate the performance of the MC cartridge, two high performance MC transformers are mounted on the MC input independently on the left and right sides.This transformer has a 2-coil configuration and uses double shielding in the core direction and winding direction. It has a quality close to that of the high-sound MC transformer MC1000.The step-up ratio is switchable between High and Low.The power supply section is equipped with a large transformer and a 90,000 ? F large electrolytic capacitor.In particular, toroidal transformers are shielded by three layers of silicon steel plates to prevent flux.Copper-plated steel sheet material Copper-Tight is used throughout the chassis, and the uniform copper-plated finish of Copper-Tight is more effective than conventional copper plating.Thorough tuning has been applied, such as using parts that have been examined through hearing.We have adopted a pair electrolytic capacitor with equivalent characteristics and sound quality, and switches with improved sound quality by copper-plating. In addition, 70-micron thick circuit boards and oxygen-free copper wires are used.AC100V Made In Japan.

Pre-main amplifier with Marantzs separate amplifier technology.The output stage is a triple push-pull configuration using MOS FET.MOS FET has characteristics such as excellent high-frequency characteristics, high withstand voltage and high power can be applied at the same time, because it operates only with majority carriers in principle, high input impedance higher than that of J-FET is realized, and because there is little accumulation effect during switching, turn-off time is extremely shortened and high-speed switching is possible. Together with Marantzs original Quarter A, MOS FET realizes ideal operation.Using a unique Quarter A circuit, it performs full class A operation up to 1/4 of the maximum output and automatically shifts to class AB operation up to the maximum output. This autoshift is controlled by an electronic control. It detects the output voltage of the main amplifier and controls the bias current with a high-speed switching circuit.The detection speed of the PM-94 circuit is higher than that of the conventional Quarter A circuit, enabling smoother control.In order to fully demonstrate the performance of the MC cartridge, two high performance MC transformers are mounted on the MC input independently on the left and right sides.This transformer has a 2-coil configuration and uses double shielding in the core direction and winding direction. It has a quality close to that of the high-sound MC transformer MC1000.The step-up ratio is switchable between High and Low.The power supply section is equipped with a large transformer and a 90,000 ? F large electrolytic capacitor.In particular, toroidal transformers are shielded by three layers of silicon steel plates to prevent flux.Copper-plated steel sheet material Copper-Tight is used throughout the chassis, and the uniform copper-plated finish of Copper-Tight is more effective than conventional copper plating.Thorough tuning has been applied, such as using parts that have been examined through hearing.We have adopted a pair electrolytic capacitor with equivalent characteristics and sound quality, and switches with improved sound quality by copper-plating. In addition, 70-micron thick circuit boards and oxygen-free copper wires are used.AC100V Made In Japan.

Pre-main amplifier with Marantzs separate amplifier technology.The output stage is a triple push-pull configuration using MOS FET.MOS FET has characteristics such as excellent high-frequency characteristics, high withstand voltage and high power can be applied at the same time, because it operates only with majority carriers in principle, high input impedance higher than that of J-FET is realized, and because there is little accumulation effect during switching, turn-off time is extremely shortened and high-speed switching is possible. Together with Marantzs original Quarter A, MOS FET realizes ideal operation.Using a unique Quarter A circuit, it performs full class A operation up to 1/4 of the maximum output and automatically shifts to class AB operation up to the maximum output. This autoshift is controlled by an electronic control. It detects the output voltage of the main amplifier and controls the bias current with a high-speed switching circuit.The detection speed of the PM-94 circuit is higher than that of the conventional Quarter A circuit, enabling smoother control.In order to fully demonstrate the performance of the MC cartridge, two high performance MC transformers are mounted on the MC input independently on the left and right sides.This transformer has a 2-coil configuration and uses double shielding in the core direction and winding direction. It has a quality close to that of the high-sound MC transformer MC1000.The step-up ratio is switchable between High and Low.The power supply section is equipped with a large transformer and a 90,000 ? F large electrolytic capacitor.In particular, toroidal transformers are shielded by three layers of silicon steel plates to prevent flux.Copper-plated steel sheet material Copper-Tight is used throughout the chassis, and the uniform copper-plated finish of Copper-Tight is more effective than conventional copper plating.Thorough tuning has been applied, such as using parts that have been examined through hearing.We have adopted a pair electrolytic capacitor with equivalent characteristics and sound quality, and switches with improved sound quality by copper-plating. In addition, 70-micron thick circuit boards and oxygen-free copper wires are used.AC100V Made In Japan.

Pre-main amplifier with Marantzs separate amplifier technology.The output stage is a triple push-pull configuration using MOS FET.MOS FET has characteristics such as excellent high-frequency characteristics, high withstand voltage and high power can be applied at the same time, because it operates only with majority carriers in principle, high input impedance higher than that of J-FET is realized, and because there is little accumulation effect during switching, turn-off time is extremely shortened and high-speed switching is possible. Together with Marantzs original Quarter A, MOS FET realizes ideal operation.Using a unique Quarter A circuit, it performs full class A operation up to 1/4 of the maximum output and automatically shifts to class AB operation up to the maximum output. This autoshift is controlled by an electronic control. It detects the output voltage of the main amplifier and controls the bias current with a high-speed switching circuit.The detection speed of the PM-94 circuit is higher than that of the conventional Quarter A circuit, enabling smoother control.In order to fully demonstrate the performance of the MC cartridge, two high performance MC transformers are mounted on the MC input independently on the left and right sides.This transformer has a 2-coil configuration and uses double shielding in the core direction and winding direction. It has a quality close to that of the high-sound MC transformer MC1000.The step-up ratio is switchable between High and Low.The power supply section is equipped with a large transformer and a 90,000 ? F large electrolytic capacitor.In particular, toroidal transformers are shielded by three layers of silicon steel plates to prevent flux.Copper-plated steel sheet material Copper-Tight is used throughout the chassis, and the uniform copper-plated finish of Copper-Tight is more effective than conventional copper plating.Thorough tuning has been applied, such as using parts that have been examined through hearing.We have adopted a pair electrolytic capacitor with equivalent characteristics and sound quality, and switches with improved sound quality by copper-plating. In addition, 70-micron thick circuit boards and oxygen-free copper wires are used.AC100V Made In Japan.

Pre-main amplifier with Marantzs separate amplifier technology.The output stage is a triple push-pull configuration using MOS FET.MOS FET has characteristics such as excellent high-frequency characteristics, high withstand voltage and high power can be applied at the same time, because it operates only with majority carriers in principle, high input impedance higher than that of J-FET is realized, and because there is little accumulation effect during switching, turn-off time is extremely shortened and high-speed switching is possible. Together with Marantzs original Quarter A, MOS FET realizes ideal operation.Using a unique Quarter A circuit, it performs full class A operation up to 1/4 of the maximum output and automatically shifts to class AB operation up to the maximum output. This autoshift is controlled by an electronic control. It detects the output voltage of the main amplifier and controls the bias current with a high-speed switching circuit.The detection speed of the PM-94 circuit is higher than that of the conventional Quarter A circuit, enabling smoother control.In order to fully demonstrate the performance of the MC cartridge, two high performance MC transformers are mounted on the MC input independently on the left and right sides.This transformer has a 2-coil configuration and uses double shielding in the core direction and winding direction. It has a quality close to that of the high-sound MC transformer MC1000.The step-up ratio is switchable between High and Low.The power supply section is equipped with a large transformer and a 90,000 ? F large electrolytic capacitor.In particular, toroidal transformers are shielded by three layers of silicon steel plates to prevent flux.Copper-plated steel sheet material Copper-Tight is used throughout the chassis, and the uniform copper-plated finish of Copper-Tight is more effective than conventional copper plating.Thorough tuning has been applied, such as using parts that have been examined through hearing.We have adopted a pair electrolytic capacitor with equivalent characteristics and sound quality, and switches with improved sound quality by copper-plating. In addition, 70-micron thick circuit boards and oxygen-free copper wires are used.AC100V Made In Japan.

THANK YOU FOR 10 AWESOME YEARS MY FRIEND !! UP TO 12% ADDITIONAL DISCOUNT WHEN YOU PURCHASE MULTIPLE B.I.N. ITEMS CHECK OUT THE WEEKLY AUCTION SPECIALS FOR MORE ATTIC FINDS !! SOMETHING NEW, SOMETHING OLD... ITEMS MEEK, ITEMS BOLD THE RAINGERS ATTIC HIGHLY RATED FIND ! 1985 MARANTZ INEGRATED AMPLIFIER QUARTER A mosFET PM-94 USA A 2 x 140 watt stereo integrated amplifier with a Mosfet power stage, which operates in Class A mode at normal listening levels and switches automatically to Class AB mode to handle high peaks and at high listening levels. Inputs for Phono (MM/MC), CD, Tuner, Aux1, Aux2, input/outputs for 3 Tape recorders (DAT/Tape1, DAT/Tape2, Hi-Fi VCR), and terminals for two pairs of loudspeakers (System 1, 2). Sockets for Pre Out and Main In. On the front, push buttons for Power, Speakers (1, 2), Tone Defeat, Tape Monitor (Source, DAT/Tape1,DAT/Tape2, Hi-Fi VCR), Muting, Subsonic filter, Mono and CD/Phono Direct, rotary controls for Treble Left, Treble Right, Bass Left, Bass Right,Volume and Balance, rotary switches for Selector (CD, Phono,Tuner, Aux1, Aux2), Phono (MM, MC High, MC Low) and Tape Copy (Hi-Fi VCR > Tape 1/2, Source, Tape 1 > Tape 2/Hi-Fi VCR, Tape 2 > Tape 1/Hi-Fi VCR). Jack for headphones.USED Authentic: MarantzEstimated Size: 19 X 16 X 6 Estimated Weight: 35 Pounds Material: Multiple As shown in photos Will package carefully SHIPS W/ FREE INSURANCE & TRACKING! Smoke free HomePlease examine Pictures as they part of item description! If you have any questions about a listing please ask prior to committing yourself !! If an item does not arrive in stated/ pictured condition, please contact me before posting feedback or opening a return ! I will work with you to resolve any life happens moments that may occur. I have an excellent track record and work hard to maintain outstanding 100% - 5 Star feedback. Let me find you the right answer BEFORE you bid. I purchase many items at retail stores, storage auctions, estate sales, High line Auctions etc. Shipping costs include and not limited to: Boxes, Bubble Mailer, Packing Paper, Toner, Standard paper, etc. I DO NOT INCLUDE INVOICES!! If you you need one or have a special request just ask I will do my best to accommodate you. I am a Air Force Vet on disability and I do this for pocket change and to support our Military and Wounded Warriors in the community. Posted Positive Feedback is appreciated ! Thanks for your time, good luck and God Bless!!USPS PACKAGE TRACKING IS NOT 100% ACCURATE! ITS A GUIDE!

Pre-main amplifier with Marantzs separate amplifier technology.The output stage is a triple push-pull configuration using MOS FET.MOS FET has characteristics such as excellent high-frequency characteristics, high withstand voltage and high power can be applied at the same time, because it operates only with majority carriers in principle, high input impedance higher than that of J-FET is realized, and because there is little accumulation effect during switching, turn-off time is extremely shortened and high-speed switching is possible. Together with Marantzs original Quarter A, MOS FET realizes ideal operation.Using a unique Quarter A circuit, it performs full class A operation up to 1/4 of the maximum output and automatically shifts to class AB operation up to the maximum output. This autoshift is controlled by an electronic control. It detects the output voltage of the main amplifier and controls the bias current with a high-speed switching circuit.The detection speed of the PM-94 circuit is higher than that of the conventional Quarter A circuit, enabling smoother control.In order to fully demonstrate the performance of the MC cartridge, two high performance MC transformers are mounted on the MC input independently on the left and right sides.This transformer has a 2-coil configuration and uses double shielding in the core direction and winding direction. It has a quality close to that of the high-sound MC transformer MC1000.The step-up ratio is switchable between High and Low.The power supply section is equipped with a large transformer and a 90,000 ? F large electrolytic capacitor.In particular, toroidal transformers are shielded by three layers of silicon steel plates to prevent flux.Copper-plated steel sheet material Copper-Tight is used throughout the chassis, and the uniform copper-plated finish of Copper-Tight is more effective than conventional copper plating.Thorough tuning has been applied, such as using parts that have been examined through hearing.We have adopted a pair electrolytic capacitor with equivalent characteristics and sound quality, and switches with improved sound quality by copper-plating. In addition, 70-micron thick circuit boards and oxygen-free copper wires are used.

Item TitleMarantz Pm-94 Integrated Lifier Payment Supports managed payments Please pay within 5 days after auction is finished. About Us We are located in Japan. Its our pleasure to make you happy by proposing our recommend item. If you have any questions or request about items please feel free to ask us. International Buyers - Please Note: -Import duties taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. -Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. -These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges. -We do not mark merchandise values below value or mark items as - gifts - The US and International government regulations prohibit such behavior. Thank you for your understanding.

Ampli MARANTZ PM-94 Avec le Quarter A original de Marantz, MOS FET ralise un fonctionnement idal. Ltage de sortie est une configuration triple push-pull utilisant MOS FET. MOS FET prsente des caractristiques telles que dexcellentes caractristiques haute frquence Le matriau en tle dacier plaqu cuivre Copper-Tight est utilis dans tout le chssis, et la finition uniforme plaque cuivre de Copper-Tight est plus efficace que le placage de cuivre conventionnel Les 35 premier watts sont en pure class A puis bascule en Class AB pour dlivrer 140 watt Lors de rvision pre out - main in ont t shunter pour une qualit de son optimale En trsbon tat desthtique et de fonctionnement PAS DENVOI APPAREILLOURD ET FRAGILE 23 KG REMISE EN MAIN PROPREUNIQUEMENT