Bias weight (Anti skate) for Pioneer PL-15 and PL15C. Aluminum weight for lower tracking force see note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-15 / 15C. One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the lighter alloy weight weight used if your cartridge tracking force is set to 2.0g or less. If your tracking force is higher than 2.0g you need the Brass version of the anti skate weight. I have this in another listing as well as a listing for both versions. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

trs belle platine vinyle tourne disque Pioneer pl 15D semi auto des annes 70 trs bon tat une juste une petite encoche au capot ct gauche cest discret et a vite les traces de doigt ... le son est impecable teste sur ampli Yamaha et enceintes b&w emballage maxi ,envoi rapide et soign comme toujours...

Bias weight (Anti skate) for Pioneer PL-15 and PL15C. Heavier Brass version of weight for cartridge tracking forces above 2.1g. See note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-15 / 15C. One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the heavier Brass weight used if your cartridge tracking force is set to 2.1g or more. If your tracking force is less than 2.1g you need the lighter Alloy version of the anti skate weight. I have this in another listing as well as a listing for both versions. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Bias weight (Anti skate) for Pioneer PL-15 and PL15C. Aluminum weight for lower tracking force see note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-15 / 15C. One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the lighter alloy weight weight used if your cartridge tracking force is set to 2.0g or less. If your tracking force is higher than 2.0g you need the Brass version of the anti skate weight. I have this in another listing as well as a listing for both versions. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Bias weight (Anti skate) for Pioneer PL-15 and PL15C. Heavier Brass version of weight for cartridge tracking forces above 2.1g. See note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-15 / 15C. One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the heavier Brass weight used if your cartridge tracking force is set to 2.1g or more. If your tracking force is less than 2.1g you need the lighter Alloy version of the anti skate weight. I have this in another listing as well as a listing for both versions. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Bias weight (Anti skate) for Pioneer PL-15 and PL15C. Aluminum weight for lower tracking force see note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-15 / 15C. One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the lighter alloy weight weight used if your cartridge tracking force is set to 2.0g or less. If your tracking force is higher than 2.0g you need the Brass version of the anti skate weight. I have this in another listing as well as a listing for both versions. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

This is for a Pioneer PL-15D II Record Player with Wood Case and dust cover. This is approximately 17 wide x 16.5 deep x 6.5 tall. This seems to play good from when I tested it. It plays records good and the up and down feature works as well as the stop button. The stop button makes the arm lift and go into resting position but sometimes the record keeps spinning. The 33 and 45 button changes the speed. The dust cover has some marks but no cracks and the case is very nice still with wood grain finish. Has a Pioneer needle and seems to be in good condition. The playback was quiet but sounded good still. I didnt have it hooked up to a pre-amp. I am selling as is but seems to be in good condition with a few minor issues, such as the stop button not always working. Please see pictures for more details and feel free to ask any questions

Bias weight (Anti skate) for Pioneer PL-15 and PL15C. Heavier Brass version of weight for cartridge tracking forces above 2.1g. See note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-15 / 15C. One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the heavier Brass weight used if your cartridge tracking force is set to 2.1g or more. If your tracking force is less than 2.1g you need the lighter Alloy version of the anti skate weight. I have this in another listing as well as a listing for both versions. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Bias weight (Anti skate) for Pioneer PL-15 and PL15C. Aluminum weight for lower tracking force see note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-15 / 15C. One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the lighter alloy weight weight used if your cartridge tracking force is set to 2.0g or less. If your tracking force is higher than 2.0g you need the Brass version of the anti skate weight. I have this in another listing as well as a listing for both versions. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *

Available is a K2 microswitch from a Pioneer PL-15R turntable that is in very good condition. Whats included is what is pictured.We ship internationally through eBay International Standard Delivery. When possible we will combine shipments and refund any excess shipping costs paid.

Available is a tone arm rest from a Pioneer PL-15R turntable that is in very good condition. Whats included is what is pictured.We ship internationally through eBay International Standard Delivery. When possible we will combine shipments and refund any excess shipping costs paid.

Available is a tone arm rest from a Pioneer PL-15R turntable that is in very good condition. Whats included is what is pictured.We ship internationally through eBay International Standard Delivery. When possible we will combine shipments and refund any excess shipping costs paid.

Bias weight (Anti skate) for Pioneer PL-15 and PL15C. Aluminum weight for lower tracking force see note below. ** NOTE. There are two anti skate weights provided with the Pioneer PL-15 / 15C. One lighter Alloy for lower tracking forces and a Brass one for tracking forces > 2.1g. This is the lighter alloy weight weight used if your cartridge tracking force is set to 2.0g or less. If your tracking force is higher than 2.0g you need the Brass version of the anti skate weight. I have this in another listing as well as a listing for both versions. ** This anti skate weight is made as a close replica of the original. It is made to the correct mass value required but it my differ cosmetically to the original manufacturers weight. * Please note that this auction is for the anti skate weight and its monofilament line only. The line is knotted and has a small balancer that goes inside the weight but the end that attaches to the anti skate bar of the tonearm is open ended and therefore you must tie the loop end yourself. Length of the line supplied is 25cm which is enough extra line for a couple of attempts and I will supply extra lines if you feel you might need them for free on request. *