Phase Linear Model 7000 cassette player

This is a used pair of the very fine and very expensive (when produced) and very rare Technics SB-7000A speakers, made in 1978. They are true linear phase design speakers and their sound is incredible across all ranges and frequencies. The list price in 1978 was $800. That is $3700 in todays dollars. You would be very hard pressed to find a pair of these in better shape physically and sonically. I had the crossover boards re-capped by an expert some time back. I just had the woofers professionally re-foamed by the great Midwest Speaker Repair shop in Roseville, MN. The total cost (with substantial shipping cost both ways) was a little over $200. They done a super job. The speakers just sound absolutely fantastic now.They also replaced the dust covers over the woofer drivers.They did have some light glue smudges resulting from their work, but it is only a surface issue on the woofers. I pictured those smudges. But of course the woofers are not even seen with the covers on them. The 4 covers are in super overall shape, especially considering their 45 year age. Some specs: 7000A Type: 3 way, 3 driver loudspeaker system Frequency Response: 37Hz to 22kHz Power Handling: 100W Crossover Frequency: 700, 6000Hz Impedance: 6? Sensitivity: 90.5dB Bass: 1 x 14 inch woofer Midrange: 1 x 5 inch cone Tweeter: 1 x 32mm dome tweeter Enclosure: bass reflex Dimensions: 19 inches wide x 33 inches high x 16 inches deepWeight: 73 lbs. Note they are 6 ohm speakers so make sure your amplifier is rated to handle such.Also note the are 73 lbs each and BIG, so shipping is pretty much out of the question. I have two owners manuals, each serial-numbered to each speaker. I would be happy and proud to show you what they can do if you wish to come look and listen to them. I would not think of selling them, but I have decided to sell my house, my estate, and most of my belongings and move to SE Asia. They HAVE to be picked up locally in Booneville, Arkansas, 35 miles SE of Fort Smith. Feel free to ask me any questions. Thank you for looking! GOD SAVE AMERICA.

GS Audio Inc. is not the owner or seller of these goods, but merely a bailee acting on behalf of the seller to facilitate the sale of the goods by holding the goods until such time as a sale is completed and the goods are shipped to the buyer. GS Audio Inc. has used its best efforts to inspect the item(s) for sale and create descriptions and furnish photographs that fairly and adequately depict the type, condition and image of the goods at the time of sale. GS Audio Inc. makes no express or implied warranties or representations regarding the condition or suitability of the goods and to the extent allowed by law, specifically disclaims any express or implied warranties, including but not limited to any warranty of merchantability or fitness for purpose. GS Audio Inc. reserves the right to cancel bids on any item due to feedback. This Listing Powered By

Phase Linear Model 7000 cassette player

This is a used pair of the very fine and very expensive (when produced) and very rare Technics SB-7000A speakers, made in 1978. They are true linear phase design speakers and their sound is incredible across all ranges and frequencies. The list price in 1978 was $800. That is $3700 in todays dollars. You would be very hard pressed to find a pair of these in better shape physically and sonically. I had the crossover boards re-capped by an expert some time back. I just had the woofers professionally re-foamed by the great Midwest Speaker Repair shop in Roseville, MN. The total cost (with substantial shipping cost both ways) was a little over $200. They done a super job. The speakers just sound absolutely fantastic now.They also replaced the dust covers over the woofer drivers.They did have some light glue smudges resulting from their work, but it is only a surface issue on the woofers. I pictured those smudges. But of course the woofers are not even seen with the covers on them. The 4 covers are in super overall shape, especially considering their 45 year age. Some specs: 7000A Type: 3 way, 3 driver loudspeaker system Frequency Response: 37Hz to 22kHz Power Handling: 100W Crossover Frequency: 700, 6000Hz Impedance: 6? Sensitivity: 90.5dB Bass: 1 x 14 inch woofer Midrange: 1 x 5 inch cone Tweeter: 1 x 32mm dome tweeter Enclosure: bass reflex Dimensions: 19 inches wide x 33 inches high x 16 inches deepWeight: 73 lbs. Note they are 6 ohm speakers so make sure your amplifier is rated to handle such.Also note the are 73 lbs each and BIG, so shipping is pretty much out of the question. I have two owners manuals, each serial-numbered to each speaker. I would be happy and proud to show you what they can do if you wish to come look and listen to them. I would not think of selling them, but I have decided to sell my house, my estate, and most of my belongings and move to SE Asia. They HAVE to be picked up locally in Booneville, Arkansas, 35 miles SE of Fort Smith. Feel free to ask me any questions. Thank you for looking! GOD SAVE AMERICA.

This is a used pair of the very fine and very expensive (when produced) and very rare Technics SB-7000A speakers, made in 1978. They are true linear phase design speakers and their sound is incredible across all ranges and frequencies. The list price in 1978 was $800. That is $3700 in todays dollars. You would be very hard pressed to find a pair of these in better shape physically and sonically. I had the crossover boards re-capped by an expert some time back. I just had the woofers professionally re-foamed by the great Midwest Speaker Repair shop in Roseville, MN. The total cost (with substantial shipping cost both ways) was a little over $200. They done a super job. The speakers just sound absolutely fantastic now.They also replaced the dust covers over the woofer drivers.They did have some light glue smudges resulting from their work, but it is only a surface issue on the woofers. I pictured those smudges. But of course the woofers are not even seen with the covers on them. The 4 covers are in super overall shape, especially considering their 45 year age. Some specs: 7000A Type: 3 way, 3 driver loudspeaker system Frequency Response: 37Hz to 22kHz Power Handling: 100W Crossover Frequency: 700, 6000Hz Impedance: 6? Sensitivity: 90.5dB Bass: 1 x 14 inch woofer Midrange: 1 x 5 inch cone Tweeter: 1 x 32mm dome tweeter Enclosure: bass reflex Dimensions: 19 inches wide x 33 inches high x 16 inches deepWeight: 73 lbs. Note they are 6 ohm speakers so make sure your amplifier is rated to handle such.Also note the are 73 lbs each and BIG, so shipping is pretty much out of the question. I have two owners manuals, each serial-numbered to each speaker. I would be happy and proud to show you what they can do if you wish to come look and listen to them. I would not think of selling them, but I have decided to sell my house, my estate, and most of my belongings and move to SE Asia. They HAVE to be picked up locally in Booneville, Arkansas, 35 miles SE of Fort Smith. Feel free to ask me any questions. Thank you for looking! GOD SAVE AMERICA.

Phase Linear Model 7000 cassette player

This is a used pair of the very fine and very expensive (when produced) and very rare Technics SB-7000A speakers, made in 1978. They are true linear phase design speakers and their sound is incredible across all ranges and frequencies. The list price in 1978 was $800. That is $3700 in todays dollars. You would be very hard pressed to find a pair of these in better shape physically and sonically. I had the crossover boards re-capped by an expert some time back. I just had the woofers professionally re-foamed by the great Midwest Speaker Repair shop in Roseville, MN. The total cost (with substantial shipping cost both ways) was a little over $200. They done a super job. The speakers just sound absolutely fantastic now.They also replaced the dust covers over the woofer drivers.They did have some light glue smudges resulting from their work, but it is only a surface issue on the woofers. I pictured those smudges. But of course the woofers are not even seen with the covers on them. The 4 covers are in super overall shape, especially considering their 45 year age. Some specs: 7000A Type: 3 way, 3 driver loudspeaker system Frequency Response: 37Hz to 22kHz Power Handling: 100W Crossover Frequency: 700, 6000Hz Impedance: 6? Sensitivity: 90.5dB Bass: 1 x 14 inch woofer Midrange: 1 x 5 inch cone Tweeter: 1 x 32mm dome tweeter Enclosure: bass reflex Dimensions: 19 inches wide x 33 inches high x 16 inches deepWeight: 73 lbs. Note they are 6 ohm speakers so make sure your amplifier is rated to handle such.Also note the are 73 lbs each and BIG, so shipping is pretty much out of the question. I have two owners manuals, each serial-numbered to each speaker. I would be happy and proud to show you what they can do if you wish to come look and listen to them. I would not think of selling them, but I have decided to sell my house, my estate, and most of my belongings and move to SE Asia. They HAVE to be picked up locally in Booneville, Arkansas, 35 miles SE of Fort Smith. Feel free to ask me any questions. Thank you for looking! GOD SAVE AMERICA.

Phase Linear Model 7000 cassette player

Sono 20 MJ 21194G consigliatimi da un anziano riparatore conosciutissimo per la sua bravura- Sono siglati ON Mexico ma si sa che sono Motorola -Non sono fake perche li ho comperati da uno dei fornitori piu seri del Web ed ho anche la fattura. Per riparare il mio Phase lenear 700B , ho sbagliato e praticamente me ne sono arrivati il doppio con due o tre forniture. ma non mi importa perchè il mio ampli canta che è una meraviglia- Vanno benissimo anche per il phase 400 e molti altri amplificatori- adesso costano 8,90 luno + iva e quindi in totale 217,16 euro = grosso sconto a 144 euro Vendita AS IS senza garanzia in ottemperanza alla legge CEE-Una volta consegnato loggetto al vettore cessa la responsabilità per il trasporto.Chi non e daccordo con i dettami dellinserzione si astenga dalla gara e dallacquisto-

Sono 20 MJ 21194G consigliatimi da un anziano riparatore conosciutissimo per la sua bravura- Sono siglati ON Mexico ma si sa che sono Motorola -Non sono fake perche li ho comperati da uno dei fornitori piu seri del Web ed ho anche la fattura. Per riparare il mio Phase lenear 700B , ho sbagliato e praticamente me ne sono arrivati il doppio con due o tre forniture. ma non mi importa perchè il mio ampli canta che è una meraviglia- Vanno benissimo anche per il phase 400 e molti altri amplificatori- adesso costano 8,90 luno + iva e quindi in totale 217,16 euro = grosso sconto a 144 euro Vendita AS IS senza garanzia in ottemperanza alla legge CEE-Una volta consegnato loggetto al vettore cessa la responsabilità per il trasporto.Chi non e daccordo con i dettami dellinserzione si astenga dalla gara e dallacquisto-

LAST PRICE REDUCTION. IF NOSALES WILL CEASE LISTINGS. EACH UNIT CUSTOM HAND ASSEMBLED! PLEASE READ THE ENTIRE LISTING CAREFULLY. PLEASE ASK ANY QUESTIONS YOU MIGHT HAVE PRIOR TO BIDDING ASTHERE ARE NO RETURNS/REFUNDS WE DEFINITELY SELL INTERNATIONALLY BUT YOU MUST CONTACT US DIRECT FIRST THROUGHMESSAGING OPTION TO ARRANGE TO DO SO! WE HAVE THE 220v 700 SERIES EURO VERSION ON HAND JUST ASK! SHIPPING IS 2-3 BUSINESS WEEKS BUT WE USUALLY SHIP MUCH FASTER THAN THAT. (USUALLY WEEKLY HEALTH & WEATHER ALLOWING) $20 SHIPPING FOR CONTINENTAL USA ONLY. IT HAD BEEN FREE UNTIL I GOT HIT WITH A $50 SHIPPING RATE IN THE USA. IF YOU HAVE PROBLEM WITH ELECTRONIC PAYMENT LET US KNOW! DESCRIPTION IN ANOTHER EBAY AD AN ADJUSTABLE RHEOSTAT INLINE CHORD TO DRIVE YOUR FAN MOTORS ARE AVAILABLE: AC Infinity, Fan Speed Controller for 100 to 125V AC Axial Muffin Cooling Fans, Single Connector, for DIY Cooling. SEE PHOTO #8 FOR REFERENCE ONLY! THESE ARE VARIABLE SPEED RHEOSTAT CONTROLLERS TO GET EXACTLY THE SPEED AND Db SOUND LEVEL YOU WISH TO CUSTOM SET IT TO. IT CAN MATCH THE ORIGINAL BOX FACTORY FAN (OR EVEN QUIETER). NO NEED FOR THE 12V FANS ANYMORE. Please see the eBay ad for the rheostat inline chord ad. WE WOULD OFFER THEM BUT THERE IS ABSOLUTELY NO MARGIN TO SELL AT A COMPETITIVE COST. The first photo shows: The front of 700 Fan and NOS box. Box isnot included in the sale. The 2nd photo shows: The rear of the 700 fan and box. The 3rd photo shows: A rear view of the 400 seriesAmplifier (no 700 amp photos available but they are functionallyidentical) with the fan in line with the fins. It will slide over to fitsecurely against the back of the amp. NOTE: I do nothave a photo of the fan fully mounted. My jpeg file was lost andvirtually all PL fans photos on the Internet of this fanare my oldphotos. Anyone with a nice photo of these fans mountedfully on the 700unit would be greatly appreciated. That is howrare these are. I am running Dual 500s these days so I cant get the photo myself. The 4th photo shows: A front view of the 400 SeriesAmplifier (no 700 amp photos available again) with the fan in linewith the fins. It will slide over to fit securely against the back ofthe amp. The 5th photo shows: The NOS boxes for the fans. It is forillustration only and not for sale. I keep all of the boxes for all of my unitsin my collection. The 6th photo shows: The individual panels fromthe front. The 7th photo is from the back of the same panels. PHOTO #8 FOR REFERENCE ONLY! SHOWS THE AFFINITY AC VARIABLE SPEED CONTROLLER AVAILABLE FROM OTHER VENDORS ON EBAY. The 9th photo is for the joy of seeing what a decent stacklooks like. NOT included in the sale (BUT will be offered in thefuture). Enjoy! Greetings Phase linear Fans. 10 years ago, I was one of thelargest collectors of Phase linear in the USA if not the World. I had beencollecting Phase Linear since the 1980s. The Gentlemen in Washington State whoused to work at Phase Linear are the only ones I am aware of with largercollections. I believe they have sold most of these collections off. I recentlyrealized I still have 2 huge 800 square foot stereo vaults with storage rackingto the ceiling full of Phase linear equipment. There is some infill of Pioneerand Carver for the units that Phase Linear simply did not offer as options. Ialso have more Phase Linear fans than I will ever use. I have collected myPhase Linear units from around the world. At one-point I had gone through ~20%of the entire 1400 series II equalizers production in my search for the perfectones for my system. A full 50% of my collection is NOS and the rest is MINToriginals. You should know the manufacturing process was a rough one on theunits. NOS is no guarantee of perfection. Perfection came with going throughuntold numbers of units in service that were collected, and parts that weremint were interchanged out over time into one unit (or more). I have spoken toboth the designers and builders of the units who were charitable with theirtime. They shared the history, production and design of these beautiful units.Fully half of ALL the NOS units I procured had blemishes on them. Even when the4 pallets of NOS 3500 series II preamps were found I bought a dozen of thoseunits to get the flawless ones I have now (combined with the additionalcollected out in-service unit mint parts). My 7000 series II tape deck alonetook 20 units (including a NOS one) to get one with absolute MINT unblemishedparts. What I have left is a large collection of very nice units across theboard of Phase Linear to sell off. It is time to enjoy the decades ofcollecting and hard work. There was a time I sold Phase linear fans but I was notsatisfied by the way they were turning out. So, I stopped. You might be able totell I am a little bit obsessive and perfectionistic (to your benefit). I hadcollected over time several blemished original fans, spare parts as well as acollection out of an old stereo shop. Recently I thought it was time to getback to doing things right and offer them once again. The supply of these arelimited. The condition of the fans is as good as you could ever possibly get.These were done right and are blemish free. If there are any marks, again theyare from the production process. Missing panels were replaced with laser cutmates. All finishes were done again, but this time in power coated finishing.This finish is a very close match to the original finishes but far moredurable. I do have a few extra original unrestored 700 fan side panels ifsomeone is interested? They are simply left over from this process. I also havesome extra Phase Linear decals available. PhaseLinear Fan history and motor placement A little history aboutthe fans. They were very very rare. I know of only about a dozen that have everpopped up for sale outside of the ones I offer. I bought most of these back inthe day. The 1970s Boxer brand fan was extremely quiet and came infrom 22-24db range on testing. When bringing these back to the market I foundthe quietists replacement motors on the planet. They are about 24db onprofessional mic testing. The original motors were in this range as well.I find them quiet. If you have never had one on an amp you might notice a lowlevel of operation but most do not. So far feedback has always been good.However, the level of noticeable air movement can vary. The way to get themsuper quiet is to use a small step-down transformer (or rheostat) to dial inthe rotational speed of the motor units (SEE NARRATIVE AND PHOTO ABOVE). Thator going with a 12-volt motor which would fit in the shroud but still need atransformer. I have never had to do it but want to be clear on the units asstarted in the ads. The700 fans fit ALL 700 series B amp, I & II amps. Theseare narrower than the 400 series fan due to the 400-fin separation beingwider. The fan shroud assemblies for the 700 and 400 series simply slide snuglyover the cooling fins at the back and 2 alligator clips then hold the shroud tothe fins at the bottom. No modifications or work is required at all. The powerchord then plugs into the back of the amp or the wall outlet if close by. Thefans come with the standard 1-foot length chords. Longer chords are availableif needed. Just request one at no extra cost. The D or Dual 500 fans require 2special high tolerance mounting brackets. If you are purchasing a 500 seriesfan there is an additional $15.00 cost for these brackets. These cooling fansreally are a must if you use your amplifiers for any length of time at all. Theheat buildup will trigger the amp to cut out despite the passive efforts of thecooling fins at the back of the units. These Fans have been promoted inthe past as necessary to avoid burning out the main board on the amps andearned the Phase Linear amps the nickname of Flame Engineering. This ismore myth than fact. However, many of the 700 amps I have run did kick offafter about 45 minutes due to heat buildup. It is/was a common problem. I placed labels on bothsides of the fan motor in case you wanted to unscrew and reverse the directionof the motor. Some prefer the pull thru of heat while others like the pushthru. I think the resistance going against the amp may work it harder thanneeded and cools less well but it will task either. As mentioned in the Ad, therheostat shown in the photos is available to adjust the fan as variable speed.That can increase or decrease the rate of cooling or fan sound level to yourspecific needs. It is available from another vendor for $13 shipped. I cantcompete with that price. All fans are testedbefore going out. There is a one-year warranty. THERE ARE NORETURNS EXCEPT FOR UNDER WARRANTY. So, buy well. Buyers remorse has littlesympathy here especially your children biding when you are notaround. THE BUYER HAS THE CHOICEFOR MORE FANS AT A REDUCED PRICE ON LARGER NUMBER OF FANS PURCHASED. I will be offering thePhase Linear 400 series II fans, as well as all models in the 220240-volt units if you are abroad, or running your own power on 220-240 volts. Postage abroad is $60 and buyer takes the risk of shipping time and loss. See my other eBay ads for those units. Regarding Overseasshipping. YOU MUST CONTACT ME PRIOR TO PURCHASE. This is to be sure youunderstand the conditions of the sale. The overseas and shipping/buying policyis that I can provide tracking to our borders, but once it leaves our shoresand arrives at your customs, I am no longer able to track the package nor areresponsible for any loss, time of arrival or damage. THE COST OF OVERSEASSHIPPING IS $70. Unless you want faster expensive shipping with tracking andinsurance. It will run considerably more. I will call it a commercialsample to keep it moving thru your customs. I will list theseonly as long as they are bringing their value here at auction on eBay. My timeis too limited to spend on losing propositions on fine equipment. I do havemany other things to do if no one wants these. If there is adequate interest, Iwill start listing the majority of my extra Phase Linear, Pioneer, and otherassorted vintage equipment to self-off as time allows for testing and cleaning.Thank you for your forbearance and time. Ask all questions priorto bidding. All sales are final! Please see our other auctions. Track Page Views With Auctivas FREE Counter

EACH FAN SHROUD LASER CUT ACCURATE TO FACTORY TO THE LAST MICRON! CUSTOM HAND ASSEMBLED! PLEASE READ THE ENTIRE LISTING CAREFULLY. PLEASE ASK ANY QUESTIONS YOU MIGHT HAVE PRIOR TO BIDDING AS THERE ARE NO RETURNS/REFUNDS WE DEFINITELY SELL INTERNATIONALLY BUT YOU MUST CONTACT US DIRECT FIRST THROUGH MESSAGING OPTION TO ARRANGE TO DO SO! WE HAVE THE 220v FAN SHROUDS FOR 700 SERIES EURO VERSION ON HAND JUST ASK! SHIPPING IS 2-3 BUSINESS WEEKS BUT WE USUALLY SHIP MUCH FASTER THAN THAT. (USUALLY WEEKLY HEALTH & WEATHER ALLOWING) FREE SHIPPING FOR CONTINENTAL USA ONLY. IF YOU HAVE PROBLEM WITH ELECTRONIC PAYMENT LET US KNOW!YOU ARE BUYING: The full 700 fan shroud WITHOUT THE FAN MOTOR OR PHASE LINEAR DECALS. Also included with the sale is the correct zip ties, #4 motor mounting screws and useful clips. These are to clip the shroud to the bottom of the fins as designed with the factory set up.DESCRIPTIONSEE PHOTO #10 FOR REFERENCE ONLY! THESE ARE VARIABLE SPEED RHEOSTAT CONTROLLERS TO GET EXACTLY THE SPEED AND Db SOUND LEVEL YOU WISH TO CUSTOM SET IT TO. IT CAN MATCH THE ORIGINAL BOX FACTORY FAN (OR EVEN QUIETER). NO NEED FOR THE 12v FANS ANYMORE. Please see the eBay ad for the rheostat inline chord ad. WE WOULD OFFER THEM BUT THERE IS ABSOLUTELY NO MARGIN TO SELL AT A COMPETITIVE COST.The first photo shows: The full 700 fan shroud from the front. Also included with the sale is the correct zip ties, #4 motor mounting screws and useful clips. These are to clip the shroud to the bottom of the fins as designed with the factory set up.The 2nd photo shows: The full 700 fan shroud from the back. Also included with the sale is the correct zip ties, #4 motor mounting screws and useful clips. These clips the shroud to the bottom of the fins as designed with the factory set up.The 3rd photo shows: A view of the 700 series shroud left side. NOTE: I do not have a photo of the fan fully mounted. My jpeg file was lost and virtually all PL fans photos on the Internet of this fan are my old photos. Anyone with a nice photo of these fans mounted fully on the 700 unit would be greatly appreciated. That is how rare these are. I am running Dual 500’s these days so I can’t get the photo myself.The 4th photo shows: A view of the 700 series shroud right side. It will slide over to fit securely against the back of the amp.The 5th photo shows: The individual 700 panels from the front. The 6th photo is from the back of the same 700 panels. The 7th photo is for REFERENCE ONLY and shows the front of 700 Fan and NOS box. Box and full fan is not included in the sale! PLEASE SEE MY OTHER ADS FOR THE FULL CORRECT FAN AND MOTOR.The 8th photo is for REFERENCE ONLY and shows the front of 700 Fan and NOS box. Box and full fan is not included in the sale! PLEASE SEE MY OTHER ADS FOR THE FULL CORRECT FAN AND MOTOR.The 9th photo shows: for REFERENCE ONLY a back view of the 700 Series Amplifier with the fan in line with the fins. It will slide over to fit securely against the back of the amp. Box and full fan is not included in the sale! PLEASE SEE MY OTHER ADS FOR THE FULL CORRECT FAN AND MOTOR.PHOTO #10 FOR REFERENCE ONLY! SHOWS THE AFINITY AC VARIABLE SPEED CONTROLLER AVAILABLE FROM OTHER VENDORS ON EBAY.Greetings Phase linear Fans. 10 years ago, I was one of the largest collectors of Phase linear in the USA if not the World. I had been collecting Phase Linear since the 1980’s. The Gentlemen in Washington State who used to work at Phase Linear are the only ones I am aware of with larger collections. I believe they have sold most of these collections off. I recently realized I still have 2 huge 800 square foot stereo vaults with storage racking to the ceiling full of Phase linear equipment. There is some infill of Pioneer and Carver for the units that Phase Linear simply did not offer as options. I also have more Phase Linear fans than I will ever use. I have collected my Phase Linear units from around the world. At one-point I had gone through ~20% of the entire 1400 series II equalizers production in my search for the perfect ones for my system. A full 50% of my collection is NOS and the rest is MINT originals. You should know the manufacturing process was a rough one on the units. NOS is no guarantee of perfection. Perfection came with going through untold numbers of units in service that were collected, and parts that were made mint over time were interchanged out into one unit (or more). I have spoken to both the designers and builders of the units who were charitable with their time. They shared the history, production and design of these beautiful units. Fully half of ALL the NOS units I procured had blemishes on them. Even when the 4 pallets of NOS 3500 series II pre-amps were found I bought a dozen of those units to get the flawless ones I have now (combined with the additional collected out in-service unit mint parts). My 7000 series II tape deck alone took 20 units (including a NOS one) to get one with absolute MINT unblemished parts. What I have left is a large collection of very nice units across the board of Phase Linear to sell off. It is time to enjoy the decades of collecting and hard work. There was a time I sold Phase linear fans but I was not satisfied by the way they were turning out. So, I stopped. You might be able to tell I am a little bit obsessive and perfectionist (to your benefit). I had collected over time several blemished original fans, spare parts as well as a collection out of an old stereo shop. Recently I thought it was time to get back to doing things right and offer them once again. The supply of these are limited. The condition of the fans is as good as you could ever possibly get. These were done right and are blemish free. If there are any marks, again they are from the production process. Missing panels were replaced with laser cut mates. All finishes were done again, but this time in power coated finishing. This finish is a very close match to the original finishes but far more durable. I do have a few extra original unrestored 700 fan side panels if someone is interested? They are simply left over from this process. I also have some extra Phase Linear decals available. The 700-amp series fan is a VERY, VERY hard to find item. The 700 fans fit ALL 700 series B amp, I & II amps. These are narrower than the 400 series fan due to the 400-fin separation being wider. The fan shroud assemblies for the 700 and 400 series simply slide snugly over the cooling fins at the back and 2 alligator clips then hold the shroud to the fins at the bottom. No modifications or work is required at all. These cooling fans really are a must if you use your amplifiers for any length of time at all. The heat buildup will trigger the amp to cut out despite the passive efforts of the cooling fins at the back of the units. These Fans have been promoted in the past as necessary to avoid burning out the main board on the amps and earned the Phase Linear amps the nickname of “Flame Engineering”. This is more myth than fact. However, many of the 700 amps I have run did kick off after about 45 minutes due to heat buildup. It is/was a common problem. THERE ARE NO RETURNS. So, buy well. Buyer’s remorse has little sympathy here especially your children bidding when you are not around. THE WINNING BIDDER HAS CHOICE FOR MORE FAN SHROUDS AT A REDUCED PRICE IF THEY SO CHOOSE. I will be offering the Phase Linear 400 series II fan shrouds and full units as well. As well as all models in the 220-240 volt units if you are abroad, or running your own power on 220-240 volts. See my other eBay ads for those units. I will list these only as long as they are bringing their value here at auction on eBay. My time is to limited to spend on losing propositions on fine equipment. I do have many other things to do if no one wants these. If there is adequate interest I will start listing the majority of my extra Phase Linear, Pioneer, and other assorted vintage equipment to self-off as time allows for testing and cleaning. Thank you for your forbearance and time. Regarding Overseas shipping. YOU MUST CONTACT ME PRIOR TO PURCHASE. This is to be sure you understand the conditions of the sale. The overseas and shipping/buying policy is that I can provide tracking to our borders, but once it leaves our shores and arrives at your customs, I am no longer able to track the package nor are responsible for any loss, time of arrival or damage. THE COST OF OVERSEAS SHIPPING IS $70. Unless you want faster expensive shipping with tracking and insurance. It will run considerably more. I will call it a commercial sample to keep it moving thru your customs. Ask all questions prior to bidding. All sales are final! Please see our other auctions. Track Page Views With Auctivas FREE Counter

Selling as not working/parts for repair as I couldnt test it as it needs an American plug fitted that has an earth on it as this unit is 120v.As you can see, cosmetically it isnt that great. Lots of surface rust.

Sono 20 MJ 21194G consigliatimi da un anziano riparatore conosciutissimo per la sua bravura- Sono siglati ON Mexico ma si sa che sono Motorola -Non sono fake perche li ho comperati da uno dei fornitori piu seri del Web ed ho anche la fattura. Per riparare il mio Phase lenear 700B , ho sbagliato e praticamente me ne sono arrivati il doppio con due o tre forniture. ma non mi importa perchè il mio ampli canta che è una meraviglia- Vanno benissimo anche per il phase 400 e molti altri amplificatori- adesso costano 8,90 luno + iva e quindi in totale 217,16 euro = grosso sconto a 149 euro Vendita AS IS senza garanzia in ottemperanza alla legge CEE-Una volta consegnato loggetto al vettore cessa la responsabilità per il trasporto.Chi non e daccordo con i dettami dellinserzione si astenga dalla gara e dallacquisto-

recherche vu mettre phase linear 700b. ou 700b en panne pour pièces !!

Phase Linear 700B 120v Power Amplifier Phase Linear 700B 120v Power Amplifier A working example of this 120 volt Phase Linear power amplifier. Cosmetically generally good, noting the case work bent on rear LHS. Shipping to the US will be about £120. Power345 Watts / Channel @ 8 ?(1) Recommended Load Impedance4 ? 16 ?(2) Frequency Response5 Hz 25 kHz @ 1 Watt(1) Phase ShiftLagging 10° at 20 kHz(2) Total Harmonic Distortion0.25 % (1) Intermodulation Distortion0.25 %(1) Hum and Noise100 dB below rated power(2) Sensitivity1.14 Volts(2) Damping Factor1000(1) Dimensions (W x D x H)19 x 10 x 7 in.(1) [48.26 x 25.4 x 17.78 cm] Weight45 lbs.(1) [20.43 kg] Manufacturer : Phase Linear Model : 700B 120v Serial Number : 374-054B Packaging : N/A Accessories Included : N/A Price When New : ? Shipping Shipping cost:Please contact us or check listing info. If you are outside the UK you will need a shipping quote BEFORE buying. Delivery time:48 hours Payment We accept the following payment methods: Paypal Credit/Debit Card BACS Please contact us if you have any questions. Service Established in 2003, 2ndhandhifi is the UKs largest stockist of used quality audio equipment. All items are checked before despatch and guaranteed for 30 days for ebay buyers to give you peace of mind that the item will arrive safely and work exactly as per ebay descriiptions. This means that all items described as used will be in good working order but may show minimal cosmetic marks resulting from everyday use. Any more significant cosmetic issues will be highlighted in the listing if present. We accept most payment methods but card payment to our shop is preferred. We use a reputable overnight courier service - items will be despatched next working day for delivery the next working day after that, but you are welcome to collect from our sister shop in Stockton on Tees if you prefer. Check our feedback if you have any doubts about the validity of this auction or us! We are a business so (although most times we do) we cannot always answer emails over the weekend so please try to ask Monday to Friday. Important 1. If there is no buy it now price stated, please dont ask - it is intended to be an auction which will run until its end time. 2. If you are outside the UK mainland please ask us for a shipping quote BEFORE placing a bid or clicking “Buy it Now”. If you dont ask, it means you will accept our quote. We do not cut corners on shipping, we only use reliable shipping companies, and we dont profit from the shipping prices we quote. 3. For any item where there is no original packaging the shipping costs include the cost to package the item to ensure safe delivery. Larger items may be shipped on a pallet - but this usually will be stated in the listing. 4. If you win the auction or buy the item, we expect you to pay and we will issue a non payment against you if you dont. Such auctions/listings cost us time (and therefore money). Requests to cancel will be rejected.

Sono 20 MJ 21194G consigliatimi da un anziano riparatore conosciutissimo per la sua bravura- Sono siglati ON Mexico ma si sa che sono Motorola -Non sono fake perche li ho comperati da uno dei fornitori piu seri del Web ed ho anche la fattura. Per riparare il mio Phase lenear 700B , ho sbagliato e praticamente me ne sono arrivati il doppio con due o tre forniture. ma non mi importa perchè il mio ampli canta che è una meraviglia- Vanno benissimo anche per il phase 400 e molti altri amplificatori- adesso costano 8,90 luno + iva e quindi in totale 217,16 euro = grosso sconto a 149 euro Vendita AS IS senza garanzia in ottemperanza alla legge CEE-Una volta consegnato loggetto al vettore cessa la responsabilità per il trasporto.Chi non e daccordo con i dettami dellinserzione si astenga dalla gara e dallacquisto-

LAST PRICE REDUCTION. IF NO SALES WILL CEASE LISTINGS. EACH UNIT CUSTOM HAND ASSEMBLED! PLEASE READ THE ENTIRE LISTING CAREFULLY. PLEASE ASK ANY QUESTIONS YOU MIGHT HAVE PRIOR TO BIDDING AS THERE ARE NO RETURNS/REFUNDS WE DEFINITELY SELL INTERNATIONALLY BUT YOU MUST CONTACT US DIRECT FIRST THROUGH MESSAGING OPTION TO ARRANGE TO DO SO! WE HAVE THE 220v 700 SERIES EURO VERSION ON HAND JUST ASK! SHIPPING IS 2-3 BUSINESS WEEKS BUT WE USUALLY SHIP MUCH FASTER THAN THAT. (USUALLY WEEKLY HEALTH & WEATHER ALLOWING) $20 SHIPPING FOR CONTINENTAL USA ONLY. IT HAD BEEN FREE UNTIL I GOT HIT WITH A $50 SHIPPING RATE IN THE USA.IF YOU HAVE PROBLEM WITH ELECTRONIC PAYMENT LET US KNOW!DESCRIPTIONIN ANOTHER EBAY AD AN ADJUSTABLE RHEOSTAT INLINE CHORD TO DRIVE YOUR FAN MOTORS ARE AVAILABLE: AC Infinity, Fan Speed Controller for 100 to 125V AC Axial Muffin Cooling Fans, Single Connector, for DIY Cooling.SEE PHOTO #8 FOR REFERENCE ONLY! THESE ARE VARIABLE SPEED RHEOSTAT CONTROLLERS TO GET EXACTLY THE SPEED AND Db SOUND LEVEL YOU WISH TO CUSTOM SET IT TO. IT CAN MATCH THE ORIGINAL BOX FACTORY FAN (OR EVEN QUIETER). NO NEED FOR THE 12V FANS ANYMORE. Please see the eBay ad for the rheostat inline chord ad. WE WOULD OFFER THEM BUT THERE IS ABSOLUTELY NO MARGIN TO SELL AT A COMPETITIVE COST.The first photo shows: The front of 700 Fan and NOS box. Box is not included in the sale.The 2nd photo shows: The rear of the 700 fan and box.The 3rd photo shows: A rear view of the 400 series Amplifier (no 700 amp photos available but they are functionally identical) with the fan in line with the fins. It will slide over to fit securely against the back of the amp. NOTE: I do not have a photo of the fan fully mounted. My jpeg file was lost and virtually all PL fans photos on the Internet of this fan are my old photos. Anyone with a nice photo of these fans mounted fully on the 700 unit would be greatly appreciated. That is how rare these are. I am running Dual 500’s these days so I can’t get the photo myself.The 4th photo shows: A front view of the 400 Series Amplifier (no 700 amp photos available again) with the fan in line with the fins. It will slide over to fit securely against the back of the amp. The 5th photo shows: The NOS boxes for the fans. It is for illustration only and not for sale. I keep all of the boxes for all of my units in my collection.The 6th photo shows: The individual panels from the front.The 7th photo is from the back of the same panels. PHOTO #8 FOR REFERENCE ONLY! SHOWS THE AFFINITY AC VARIABLE SPEED CONTROLLER AVAILABLE FROM OTHER VENDORS ON EBAY.The 9th photo is for the joy of seeing what a decent stack looks like. NOT included in the sale (BUT will be offered in the future). Enjoy!Greetings Phase linear Fans. 10 years ago, I was one of the largest collectors of Phase linear in the USA if not the World. I had been collecting Phase Linear since the 1980’s. The Gentlemen in Washington State who used to work at Phase Linear are the only ones I am aware of with larger collections. I believe they have sold most of these collections off. I recently realized I still have 2 huge 800 square foot stereo vaults with storage racking to the ceiling full of Phase linear equipment. There is some infill of Pioneer and Carver for the units that Phase Linear simply did not offer as options. I also have more Phase Linear fans than I will ever use. I have collected my Phase Linear units from around the world. At one-point I had gone through ~20% of the entire 1400 series II equalizers production in my search for the perfect ones for my system. A full 50% of my collection is NOS and the rest is MINT originals. You should know the manufacturing process was a rough one on the units. NOS is no guarantee of perfection. Perfection came with going through untold numbers of units in service that were collected, and parts that were mint were interchanged out over time into one unit (or more). I have spoken to both the designers and builders of the units who were charitable with their time. They shared the history, production and design of these beautiful units. Fully half of ALL the NOS units I procured had blemishes on them. Even when the 4 pallets of NOS 3500 series II preamps were found I bought a dozen of those units to get the flawless ones I have now (combined with the additional collected out in-service unit mint parts). My 7000 series II tape deck alone took 20 units (including a NOS one) to get one with absolute MINT unblemished parts. What I have left is a large collection of very nice units across the board of Phase Linear to sell off. It is time to enjoy the decades of collecting and hard work. There was a time I sold Phase linear fans but I was not satisfied by the way they were turning out. So, I stopped. You might be able to tell I am a little bit obsessive and perfectionistic (to your benefit). I had collected over time several blemished original fans, spare parts as well as a collection out of an old stereo shop. Recently I thought it was time to get back to doing things right and offer them once again. The supply of these are limited. The condition of the fans is as good as you could ever possibly get. These were done right and are blemish free. If there are any marks, again they are from the production process. Missing panels were replaced with laser cut mates. All finishes were done again, but this time in power coated finishing. This finish is a very close match to the original finishes but far more durable. I do have a few extra original unrestored 700 fan side panels if someone is interested? They are simply left over from this process. I also have some extra Phase Linear decals available. Phase Linear Fan history and motor placementA little history about the fans. They were very very rare. I know of only about a dozen that have ever popped up for sale outside of the ones I offer. I bought most of these back in the day. The 1970s Boxer brand fan was extremely quiet and came in from 22-24db range on testing. When bringing these back to the market I found the quietists replacement motors on the planet. They are about 24db on professional mic testing. The original motors were in this range as well. I find them quiet. If you have never had one on an amp you might notice a low level of operation but most do not. So far feedback has always been good. However, the level of noticeable air movement can vary. The way to get them super quiet is to use a small step-down transformer (or rheostat) to dial in the rotational speed of the motor units (SEE NARRATIVE AND PHOTO ABOVE). That or going with a 12-volt motor which would fit in the shroud but still need a transformer. I have never had to do it but want to be clear on the units as started in the ads. The 700 fans fit ALL 700 series B amp, I & II amps. These are narrower than the 400 series fan due to the 400-fin separation being wider. The fan shroud assemblies for the 700 and 400 series simply slide snugly over the cooling fins at the back and 2 alligator clips then hold the shroud to the fins at the bottom. No modifications or work is required at all. The power chord then plugs into the back of the amp or the wall outlet if close by. The fans come with the standard 1-foot length chords. Longer chords are available if needed. Just request one at no extra cost. The D or Dual 500 fans require 2 special high tolerance mounting brackets. If you are purchasing a 500 series fan there is an additional $15.00 cost for these brackets. These cooling fans really are a must if you use your amplifiers for any length of time at all. The heat buildup will trigger the amp to cut out despite the passive efforts of the cooling fins at the back of the units. These Fans have been promoted in the past as necessary to avoid burning out the main board on the amps and earned the Phase Linear amps the nickname of “Flame Engineering”. This is more myth than fact. However, many of the 700 amps I have run did kick off after about 45 minutes due to heat buildup. It is/was a common problem.I placed labels on both sides of the fan motor in case you wanted to unscrew and reverse the direction of the motor. Some prefer the pull thru of heat while others like the push thru. I think the resistance going against the amp may work it harder than needed and cools less well but it will task either. As mentioned in the Ad, the rheostat shown in the photos is available to adjust the fan as variable speed. That can increase or decrease the rate of cooling or fan sound level to your specific needs. It is available from another vendor for $13 shipped. I can’t compete with that price.All fans are tested before going out. There is a one-year warranty. THERE ARE NO RETURNS EXCEPT FOR UNDER WARRANTY. So, buy well. Buyer’s remorse has little sympathy here especially your children biding when you are not around.THE BUYER HAS THE CHOICE FOR MORE FANS AT A REDUCED PRICE ON LARGER NUMBER OF FANS PURCHASED.I will be offering the Phase Linear 400 series II fans, as well as all models in the 220–240-volt units if you are abroad, or running your own power on 220-240 volts. See my other eBay ads for those units.Regarding Overseas shipping. YOU MUST CONTACT ME PRIOR TO PURCHASE. This is to be sure you understand the conditions of the sale. The overseas and shipping/buying policy is that I can provide tracking to our borders, but once it leaves our shores and arrives at your customs, I am no longer able to track the package nor are responsible for any loss, time of arrival or damage. THE COST OF OVERSEAS SHIPPING IS $70. Unless you want faster expensive shipping with tracking and insurance. It will run considerably more. I will call it a commercial sample to keep it moving thru your customs. I will list these only as long as they are bringing their value here at auction on eBay. My time is too limited to spend on losing propositions on fine equipment. I do have many other things to do if no one wants these. If there is adequate interest, I will start listing the majority of my extra Phase Linear, Pioneer, and other assorted vintage equipment to self-off as time allows for testing and cleaning. Thank you for your forbearance and time. Ask all questions prior to bidding. All sales are final! Please see our other auctions. Track Page Views With Auctivas FREE Counter

EACH FAN SHROUD LASER CUT ACCURATE TO FACTORY TO THE LAST MICRON! CUSTOM HAND ASSEMBLED! PLEASE READ THE ENTIRE LISTING CAREFULLY. PLEASE ASK ANY QUESTIONS YOU MIGHT HAVE PRIOR TO BIDDING AS THERE ARE NO RETURNS/REFUNDS WE DEFINITELY SELL INTERNATIONALLY BUT YOU MUST CONTACT US DIRECT FIRST THROUGH MESSAGING OPTION TO ARRANGE TO DO SO! WE HAVE THE 220v FAN SHROUDS FOR 700 SERIES EURO VERSION ON HAND JUST ASK! SHIPPING IS 2-3 BUSINESS WEEKS BUT WE USUALLY SHIP MUCH FASTER THAN THAT. (USUALLY WEEKLY HEALTH & WEATHER ALLOWING) FREE SHIPPING FOR CONTINENTAL USA ONLY. IF YOU HAVE PROBLEM WITH ELECTRONIC PAYMENT LET US KNOW!YOU ARE BUYING: The full 700 fan shroud WITHOUT THE FAN MOTOR OR PHASE LINEAR DECALS. Also included with the sale is the correct zip ties, #4 motor mounting screws and useful clips. These are to clip the shroud to the bottom of the fins as designed with the factory set up.DESCRIPTIONSEE PHOTO #10 FOR REFERENCE ONLY! THESE ARE VARIABLE SPEED RHEOSTAT CONTROLLERS TO GET EXACTLY THE SPEED AND Db SOUND LEVEL YOU WISH TO CUSTOM SET IT TO. IT CAN MATCH THE ORIGINAL BOX FACTORY FAN (OR EVEN QUIETER). NO NEED FOR THE 12v FANS ANYMORE. Please see the eBay ad for the rheostat inline chord ad. WE WOULD OFFER THEM BUT THERE IS ABSOLUTELY NO MARGIN TO SELL AT A COMPETITIVE COST.The first photo shows: The full 700 fan shroud from the front. Also included with the sale is the correct zip ties, #4 motor mounting screws and useful clips. These are to clip the shroud to the bottom of the fins as designed with the factory set up.The 2nd photo shows: The full 700 fan shroud from the back. Also included with the sale is the correct zip ties, #4 motor mounting screws and useful clips. These clips the shroud to the bottom of the fins as designed with the factory set up.The 3rd photo shows: A view of the 700 series shroud left side. NOTE: I do not have a photo of the fan fully mounted. My jpeg file was lost and virtually all PL fans photos on the Internet of this fan are my old photos. Anyone with a nice photo of these fans mounted fully on the 700 unit would be greatly appreciated. That is how rare these are. I am running Dual 500’s these days so I can’t get the photo myself.The 4th photo shows: A view of the 700 series shroud right side. It will slide over to fit securely against the back of the amp.The 5th photo shows: The individual 700 panels from the front. The 6th photo is from the back of the same 700 panels. The 7th photo is for REFERENCE ONLY and shows the front of 700 Fan and NOS box. Box and full fan is not included in the sale! PLEASE SEE MY OTHER ADS FOR THE FULL CORRECT FAN AND MOTOR.The 8th photo is for REFERENCE ONLY and shows the front of 700 Fan and NOS box. Box and full fan is not included in the sale! PLEASE SEE MY OTHER ADS FOR THE FULL CORRECT FAN AND MOTOR.The 9th photo shows: for REFERENCE ONLY a back view of the 700 Series Amplifier with the fan in line with the fins. It will slide over to fit securely against the back of the amp. Box and full fan is not included in the sale! PLEASE SEE MY OTHER ADS FOR THE FULL CORRECT FAN AND MOTOR.PHOTO #10 FOR REFERENCE ONLY! SHOWS THE AFINITY AC VARIABLE SPEED CONTROLLER AVAILABLE FROM OTHER VENDORS ON EBAY.Greetings Phase linear Fans. 10 years ago, I was one of the largest collectors of Phase linear in the USA if not the World. I had been collecting Phase Linear since the 1980’s. The Gentlemen in Washington State who used to work at Phase Linear are the only ones I am aware of with larger collections. I believe they have sold most of these collections off. I recently realized I still have 2 huge 800 square foot stereo vaults with storage racking to the ceiling full of Phase linear equipment. There is some infill of Pioneer and Carver for the units that Phase Linear simply did not offer as options. I also have more Phase Linear fans than I will ever use. I have collected my Phase Linear units from around the world. At one-point I had gone through ~20% of the entire 1400 series II equalizers production in my search for the perfect ones for my system. A full 50% of my collection is NOS and the rest is MINT originals. You should know the manufacturing process was a rough one on the units. NOS is no guarantee of perfection. Perfection came with going through untold numbers of units in service that were collected, and parts that were made mint over time were interchanged out into one unit (or more). I have spoken to both the designers and builders of the units who were charitable with their time. They shared the history, production and design of these beautiful units. Fully half of ALL the NOS units I procured had blemishes on them. Even when the 4 pallets of NOS 3500 series II pre-amps were found I bought a dozen of those units to get the flawless ones I have now (combined with the additional collected out in-service unit mint parts). My 7000 series II tape deck alone took 20 units (including a NOS one) to get one with absolute MINT unblemished parts. What I have left is a large collection of very nice units across the board of Phase Linear to sell off. It is time to enjoy the decades of collecting and hard work. There was a time I sold Phase linear fans but I was not satisfied by the way they were turning out. So, I stopped. You might be able to tell I am a little bit obsessive and perfectionist (to your benefit). I had collected over time several blemished original fans, spare parts as well as a collection out of an old stereo shop. Recently I thought it was time to get back to doing things right and offer them once again. The supply of these are limited. The condition of the fans is as good as you could ever possibly get. These were done right and are blemish free. If there are any marks, again they are from the production process. Missing panels were replaced with laser cut mates. All finishes were done again, but this time in power coated finishing. This finish is a very close match to the original finishes but far more durable. I do have a few extra original unrestored 700 fan side panels if someone is interested? They are simply left over from this process. I also have some extra Phase Linear decals available. The 700-amp series fan is a VERY, VERY hard to find item. The 700 fans fit ALL 700 series B amp, I & II amps. These are narrower than the 400 series fan due to the 400-fin separation being wider. The fan shroud assemblies for the 700 and 400 series simply slide snugly over the cooling fins at the back and 2 alligator clips then hold the shroud to the fins at the bottom. No modifications or work is required at all. These cooling fans really are a must if you use your amplifiers for any length of time at all. The heat buildup will trigger the amp to cut out despite the passive efforts of the cooling fins at the back of the units. These Fans have been promoted in the past as necessary to avoid burning out the main board on the amps and earned the Phase Linear amps the nickname of “Flame Engineering”. This is more myth than fact. However, many of the 700 amps I have run did kick off after about 45 minutes due to heat buildup. It is/was a common problem. THERE ARE NO RETURNS. So, buy well. Buyer’s remorse has little sympathy here especially your children bidding when you are not around. THE WINNING BIDDER HAS CHOICE FOR MORE FAN SHROUDS AT A REDUCED PRICE IF THEY SO CHOOSE. I will be offering the Phase Linear 400 series II fan shrouds and full units as well. As well as all models in the 220-240 volt units if you are abroad, or running your own power on 220-240 volts. See my other eBay ads for those units. I will list these only as long as they are bringing their value here at auction on eBay. My time is to limited to spend on losing propositions on fine equipment. I do have many other things to do if no one wants these. If there is adequate interest I will start listing the majority of my extra Phase Linear, Pioneer, and other assorted vintage equipment to self-off as time allows for testing and cleaning. Thank you for your forbearance and time. Regarding Overseas shipping. YOU MUST CONTACT ME PRIOR TO PURCHASE. This is to be sure you understand the conditions of the sale. The overseas and shipping/buying policy is that I can provide tracking to our borders, but once it leaves our shores and arrives at your customs, I am no longer able to track the package nor are responsible for any loss, time of arrival or damage. THE COST OF OVERSEAS SHIPPING IS $70. Unless you want faster expensive shipping with tracking and insurance. It will run considerably more. I will call it a commercial sample to keep it moving thru your customs. Ask all questions prior to bidding. All sales are final! Please see our other auctions. Track Page Views With Auctivas FREE Counter