RARE BRIMAR 6X4 VALVES, BOXED x2FOR QUAD II LEAK ROGERS VALVE AMPLIFIER - KT66 ECC83 U52 PX25 ETCPostage cost to UK is £10, Worldwide is £30

RARE BRIMAR 6X4 VALVES, BOXED x2FOR QUAD II LEAK ROGERS VALVE AMPLIFIER - KT66 ECC83 U52 PX25 ETCPostage cost to UK is £10, Worldwide is £30

Leak Stereo 20 power amplifier, manufactured in 1960, restored and ready to be used. All new high grade passive components. No modifications have been made to the original design of the circuitry except for where equivalent component values are no longer available so it should sound the same, or even better than when it was made in 1960? Cosmetically immaculate. There are some minor marks such as slight wear to paint on corners/edges and pinholes as shown in the photos that form part of the description. Note: this amp was designed in the 1950s to be mounted inside a cabinet, hence there are electrical safety issues if it was exposed. I have addressed many of these issues to make the amp as safe as possible when it is used on display. The bottom of the amp has been left open but a ventilated cover plate can be contained on ebay for ~£25 for further electrical protection if needed. All Resistors have been replaced with over-rated (higher wattage), high quality 2W and 5W Kiwame and Allen Bradley components. The 100? Fuse Resistor has been replaced by a 5W resistor and a Fuse has been added in-line to protect the output transformers in the event of a failure. FYI, the minimally rated fuse resistor was designed to drop off if it over-heated enough to melt the solder connections. All signal path Capacitors have been replaced with high quality F&T polyester and Mallory aluminium electrolytic components. Reservoir Capacitors have been re-stuffed with Nichicon VY polyester electrolytics to retain the original appearance. The front can is polished rather than trying to match the paint colour to the original. My objective was to restore the sound, make it safe and restore the appearance where possible. Phono Inputs have been upgraded with gold-plated components. Speaker Output terminals have been replaced with 4mm Banana Sockets. Power Input plug & socket has been removed to make electrically safe: the original Bulgin leaded socket can unscrew in situ exposing live terminals. There has been some replacement wire in the power supply wiring where original wire insulation had become brittle. Auxiliary Power Output Sockets have been removed to make electrically safe. Switch cable has been replaced by a dual-pole Power Switch and slow-startup device to protect the amp when it is switched on. This amp will be supplied with a full set of used Valves, from my stock, so that it will work out of the box. The new owner can then choose the valves that they prefer in the future if they want to upgrade. This Power Amp does not require a Powered pre-amp so most pre-amps will work, including a Passive Pre-Amp. I have tested this amp using an Onkyo Integra P-304 pre-amp. I prefer to use DPD for delivery but the item will only be insured for £50 for delivery. If the buyer wishes to insure the item for its full value then please contact me as the insurance is IRO £70. Other couriers charge a similar rate.

LEAK TL 12 PLUS POWER AMPLIFIER PLEASE MAKE PAYMENT IMMEDIATELY AS I WILL BE GOING ON HOLIDAY SHORTLY AFTERIF PAYMENT IS NOT RECEIVED IN TIME I WILL NOT BE ABLE TO SHIP UNTIL THE 15TH AUGUST IN ORIGINAL CONDITION MARKS AND WEAR COMMENSURATE WITH AGE - SEE PICS I DONT HAVE A VARIAC SO HAVE NOT DARE POWER THIS UP BUT ALL VALVES HAVE BEEN TESTED AND ARE IN WORKING ORDER THIS IS AS IN THE PICTURES - AMPLIFIER WITH VALVES - NOTHING MORE, NOTHING LESS NO POWER CORD IM AFRAID FOR THE ABOVE REASONS , SOLD AS PARTS OR NOT WORKING AS WITH ALL VINTAGE EQUIPMENT , I WOULD RECOMMEND HAVING THIS CHECKED BY A COMPETENT ENGINEER BEFORE USE PLEASE SEE PICTURES FOR DETAILS INTERNATIONAL BUYERS SHIPPING COSTS USA - £ 90CHINA & HONG KONG - £95MAINLAND EUROPE - £25GREECE - £45EIRE/N.I. - £25HIGHLANDS AND ISLANDS - £25 - PLEASE IGNORE EBAY SHIPPING COST AS I WILL SEND AN INVOICE FOR THE CORRECT AMOUNT AFTER AUCTION END ! PLEASE SEE MY OTHER AUCTIONS?

RARE BRIMAR 6X4 VALVES, BOXED x2FOR QUAD II LEAK ROGERS VALVE AMPLIFIER - KT66 ECC83 U52 PX25 ETCPostage cost to UK is £10, Worldwide is £30

Rogers Valve Power & Pre Amplifier for Rogers LS3/5A SpeakersOriginal Rogers Cadet Valve Power & Pre AmplifiersStunning like new condition, fully working order Tested on Rogers LS3/5A Speakers Made in London England - 1960sComplete set of classic Rogers audio circa 1950s Postage express worldwide, Thank you for looking

Rogers Valve Power & Pre Amplifier for Rogers LS3/5A SpeakersOriginal Rogers Cadet Valve Power & Pre AmplifiersStunning like new condition, fully working order Tested on Rogers LS3/5A Speakers Made in London England - 1960sComplete set of classic Rogers audio circa 1950s Postage express worldwide, Thank you for looking

RARE BRIMAR 6X4 VALVES, BOXED x2FOR QUAD II LEAK ROGERS VALVE AMPLIFIER - KT66 ECC83 U52 PX25 ETCPostage cost to UK is £10

Leak Stereo 20 power amplifier, manufactured in 1960, restored and ready to be used. All new high grade passive components. No modifications have been made to the original design of the circuitry except for where equivalent component values are no longer available so it should sound the same, or even better than when it was made in 1960? Cosmetically immaculate. There are some minor marks such as slight wear to paint on corners/edges and pinholes as shown in the photos that form part of the description. Note: this amp was designed in the 1950s to be mounted inside a cabinet, hence there are electrical safety issues if it was exposed. I have addressed many of these issues to make the amp as safe as possible when it is used on display. The bottom of the amp has been left open but a ventilated cover plate can be contained on ebay for ~£25 for further electrical protection if needed. All Resistors have been replaced with over-rated (higher wattage), high quality 2W and 5W Kiwame and Allen Bradley components. The 100? Fuse Resistor has been replaced by a 5W resistor and a Fuse has been added in-line to protect the output transformers in the event of a failure. FYI, the minimally rated fuse resistor was designed to drop off if it over-heated enough to melt the solder connections. All signal path Capacitors have been replaced with high quality F&T polyester and Mallory aluminium electrolytic components. Reservoir Capacitors have been re-stuffed with Nichicon VY polyester electrolytics to retain the original appearance. The front can is polished rather than trying to match the paint colour to the original. My objective was to restore the sound, make it safe and restore the appearance where possible. Phono Inputs have been upgraded with gold-plated components. Speaker Output terminals have been replaced with 4mm Banana Sockets. Power Input plug & socket has been removed to make electrically safe: the original Bulgin leaded socket can unscrew in situ exposing live terminals. There has been some replacement wire in the power supply wiring where original wire insulation had become brittle. Auxiliary Power Output Sockets have been removed to make electrically safe. Switch cable has been replaced by a dual-pole Power Switch and slow-startup device to protect the amp when it is switched on. This amp will be supplied with a full set of used Valves, from my stock, so that it will work out of the box. The new owner can then choose the valves that they prefer in the future if they want to upgrade. This Power Amp does not require a Powered pre-amp so most pre-amps will work, including a Passive Pre-Amp. I have tested this amp using an Onkyo Integra P-304 pre-amp. I prefer to use DPD for delivery but the item will only be insured for £50 for delivery. If the buyer wishes to insure the item for its full value then please contact me as the insurance is IRO £70. Other couriers charge a similar rate.

1964 Leak Stereo 20 Power Amplifier fully restored/Serviced ** SUPERB ** This beautiful amplifier has been fully restored, It comes fully serviced & re-caped by RetroAmps in Devon to a very high standard . This includes Holco and Kwami resistors, Mundorf supreme, F&T capacitors and a full set of Mullard valves .A superb sounding vintage amplifier and once coupled with LS35A speakers sonic Nirvana can be attained :) (speakers not included) For a full rundown or Demo ask ..Darren at WWW.retroamps.com Thanks for looking and check out my other amps for sale :)

This item has been professionally inspected and is authentic.Ouvopo White Battery Powered Alarm Sensor Water Leak Detectors Pack Of 6Condition: Open box - Includes all pieces - Please see photos Returns acceptedBrand: OuvopoModel: NAColor: WhiteType: Water Leak DetectorsFeatures: Alarm SensorBattery Included: YesPower Source: BatteryCountry/Region of Manufacture: China

Leak Stereo 20 power amplifier, manufactured in 1960, restored and ready to be used. All new high grade passive components. No modifications have been made to the original design of the circuitry except for where equivalent component values are no longer available so it should sound the same, or even better than when it was made in 1960? Cosmetically immaculate. There are some minor marks such as slight wear to paint on corners/edges and pinholes as shown in the photos that form part of the description. Note: this amp was designed in the 1950s to be mounted inside a cabinet, hence there are electrical safety issues if it was exposed. I have addressed many of these issues to make the amp as safe as possible when it is used on display. The bottom of the amp has been left open but a ventilated cover plate can be contained on ebay for ~£25 for further electrical protection if needed. All Resistors have been replaced with over-rated (higher wattage), high quality 2W and 5W Kiwame and Allen Bradley components. The 100? Fuse Resistor has been replaced by a 5W resistor and a Fuse has been added in-line to protect the output transformers in the event of a failure. FYI, the minimally rated fuse resistor was designed to drop off if it over-heated enough to melt the solder connections. All signal path Capacitors have been replaced with high quality F&T polyester and Mallory aluminium electrolytic components. Reservoir Capacitors have been re-stuffed with Nichicon VY polyester electrolytics to retain the original appearance. The front can is polished rather than trying to match the paint colour to the original. My objective was to restore the sound, make it safe and restore the appearance where possible. Phono Inputs have been upgraded with gold-plated components. Speaker Output terminals have been replaced with 4mm Banana Sockets. Power Input plug & socket has been removed to make electrically safe: the original Bulgin leaded socket can unscrew in situ exposing live terminals. There has been some replacement wire in the power supply wiring where original wire insulation had become brittle. Auxiliary Power Output Sockets have been removed to make electrically safe. Switch cable has been replaced by a dual-pole Power Switch and slow-startup device to protect the amp when it is switched on. This amp will be supplied with a full set of used Valves, from my stock, so that it will work out of the box. The new owner can then choose the valves that they prefer in the future if they want to upgrade. This Power Amp does not require a Powered pre-amp so most pre-amps will work, including a Passive Pre-Amp. I have tested this amp using an Onkyo Integra P-304 pre-amp. I prefer to use DPD for delivery but the item will only be insured for £50 for delivery. If the buyer wishes to insure the item for its full value then please contact me as the insurance is IRO £70. Other couriers charge a similar rate.

For sell 1 x Bulgin ( 22 mm ) 3 pin Power plug / Scoket set P.340 suitable with Quad ESL57 spk and Leak TL2 valve amp the panel plug has 40mm flange dia the socket/plug has 22mm nose dia Condition is lightly used and in very good condition with some slight user marks. Power rating : 240 AC 5 AMPS these are old electrical standards and should be use with care and attention. Payments managed by ebay Only Post to the UK only

A Leak Stereo 30 Plus integrated amplifier for spares or repair. Classic British made amplifier with wooden casing. The unit powers up, but I cannot test it further. Please assume it doesnt function, sold for spares or repair, no returns. In good cosmetic condition. Please examine the photos closely. From a smoke and pet free home. International postage available via eBays Global Shipping Programme. May incur import duty.

Leak Stereo 20 Power Amplifier + FREE TROUGH LINE II TUNER ONE OWNER FROM NEW ONLY ASKING £895 FULLY REFURBUISHED and in good/very good condition both in working order

Leak Stereo 20 Power Amplifier + FREE TROUGH LINE II TUNER ONE OWNER FROM NEW STARTING AT ONLY £775 FULLY REFURBUISHED and in good/very good condition both in working order  

For sell 1 x Bulgin Extra Large ( 27-27.5 mm ) PANEL fitting Male 3 pin Condition is NOS new old stock or as-new with some slight storage marks. size : 50mm x 50mm x panel cutting hole approx 36mm Power rating : 240 AC 7 AMPS these are old electrical standards and should be use with care and attention. Payments managed by ebay Only Post to the UK only

For sell 1 x Bulgin Extra Large ( 27-27.5 mm ) 3 pin Power plug / Scoket SA480 Condition is NOS new old stock or as-new with some slight storage marks. Power rating : 240 AC 7 AMPS these are old electrical standards and should be use with care and attention. Payments managed by ebay Only Post to the UK only

Features: ?ABS Material?The shell of mini gas detector is made of ABS, non-slip and impact resistant, it is used for fast and reliable detection of flammable gas leaks, providing great convenience for your home. Powered by 2 AAA batteries (not included). ?Combustible Gases?This gas leak detector can can be used for methane/natural gas, propane, fuel, ethane, butane, alcohol, coal gas, gasoline, toluene, kerosene, sewer gas, and other flammable gases. ?Quick Response?When a gas leak is detected, the gas sensors LED light and speaker will immediately sound an alarm within about 5 seconds. However, please note that after powering on the analyzer, you will need to wait approximately 30 seconds for the warm-up time. ?Long Probe?The handheld gas detector is equipped with a 115.7cm/6.18inch probe, allowing the users with the ability to quickly and easily detect gas leaking in most hard-to-reach areas and pinpoint the sources. ?Wide Use? Gas detection ranges from 50 to 1000 ppm, and it is suitable for propane tank, lawnmower, basement, gas line, RV, gas factory workspace, gas stove, gas oven, water heater and other household gas equipment. Specifications: Material: ABS Color: Black Size: (Approx)(LxWxH) 31.7x4.1x2.6cm/12.5x1.6x1inch Hose length: (Approx) 15.7cm/6.18inch Power by: 2 x AAA batteries (not included) Range: 50~1000ppm Detection gas: Combustible gas Accuracy: Sensitivity: Response time: About 5 seconds Warm-up time: About 30 seconds Alarm mode: Sound and light prompt Package Included: 1 x Gas Leak Detector 1 x Manual Note: 1. Due to the light and screen difference, the items color may be slightly different from the pictures. 2. Please allow 0.5-2 cm differences due to manual measurement. Payment must be received within 7 business days of auction closing. No combine postage discount We will ship the package within 1 business days after the payment cleared. We ship to Ebay address, and please make sure your ebay address correct before purchase. Delivery time: We thank you for your understanding on international shipping. We shipped the item quickly but the overseas shipping will be affected by many factors such as Customs processing, Post strike etc. As the Customs clearance process is different in different countries,if such kind of goods need be collected tariff buyer needs to pay for the tariff. Anyway we will try our best to avoid this kind of thing. We greatly appreciate your POSITIVE feedback. Please do NOT leave negative feedback without asking for help Our aim is to provide Top Level Customer Service, so we will try our best to solve any problem. Please DONT leave negative or neutral feedback if you havent received item in 30 days, because we have mentioned the shipping time repeatedly. We accept return within 30 days since you received your package. Please contact us for return or refund. Our working time: Monday- Saturday (Greenwich Time 2:30A.M-11:30A.M ) ( Pacific Time:6:30P.M-3:30A.M) Please only use Ebay message to contact us (my ebay-won items-contact seller) All messages will be answered within 1 business day. If you do not receive our reply, please kindly re-sent your email and we will reply to you as soon as possible.

Stern Radio Ltd Mullard 5-10 10W EL84 valve power amplifier** International shipping. All our items are also available for viewing and collection by appointment from our new showroom in Brighton/UK **A good example of this highly regarded amplifier.Overall, very good cosmetic condition. Lacking most valves. Untested, and please assume that it will need a technical service prior to use.Please note: no additional plugs/cables or valves/tubes are included in this sale (only 2 valves are present)Dimensions: approx.: width 26 cm, depth 18 cm; height 16 cm; Weight each approx.: 5 kg Shipping info: Package details: dimensions approx. 36 x 30 x 25 cm; weight approx. 8 kg. Shipping Costs: UK £12, Europe £20, USA £35, Asia £47PAYMENTPayment within 5 days of purchase please. For other arrangements please make contact before bidding/buying. QUESTIONS ETCAny questions, please ask! For more info, contact me via eBay or by phone on +44 7837 410546. Contact details are also in the business seller information. TRANSPORT/ SHIPPINGSecurely and professionally packaged & insured international shippingAll transport prices are door-to-door and include full insurance. Buyer is to pay all import taxes/duties/customs charges in their country, plus any additional charges for remote areas (prices quoted are for main towns and cities, not remote countryside areas - if in doubt, please send details and I will quote accurate price. Cash on collection also very welcome (Central London or Brighton, UK).Please note: there are some shipping/customs delays to Europe following Brexit. PHOTOSAll photos are copyright © Works of Design Ltd. Please let us know if any items are unclear or if you would like additional photos. ABOUT USWORKS OF DESIGN (eBay ID stackingsystem) is a UK based audio and design consultancy with a carefully curated selection of works for sale. +++ Please see our other vintage design and audio items !! +++

RCA High Fidelity Power Amplifier LMI-32216 A (SINGLE MONO UNIT)** International shipping. All our items are also available for viewing and collection by appointment from our new showroom in Brighton/UK **A good example of this highly regarded amplifier.Please note: no plugs or cables or valves/tubes are included in this sale – this is as we received it. valves required are: ef86 x2, kt66 x2, gz32.Cosmetic: Overall good and solid and rust-free. Front text/transfer has some damage. One end appears pushed in at the base– see photos. This doesn’t affect the top of the chassis, and there doesn’t seem to be any paint damage or surrounding damage. It seems almost as if it has always been like this. This could probably be pulled out, but we will leave this to the buyer to decide. Technical: We have not tested the amp, and please assume that it will need a service prior to use. It appears that some components have been updated at some stage.Dimensions: approx.: width 41 cm, depth 20 cm; height 19 cm; Weight estimated approx.: 12kg Shipping info: Package details: dimensions approx. 50 x 30 x 30 cm; weight approx. 19 kg. Shipping Costs: UK £14, Europe £25, USA £72, Asia £77PAYMENTPayment within 5 days of purchase please. For other arrangements please make contact before bidding/buying. QUESTIONS ETCAny questions, please ask! For more info, contact me via eBay or by phone on +44 7837 410546. Contact details are also in the business seller information. TRANSPORT/ SHIPPINGSecurely and professionally packaged & insured international shippingAll transport prices are door-to-door and include full insurance. Buyer is to pay all import taxes/duties/customs charges in their country, plus any additional charges for remote areas (prices quoted are for main towns and cities, not remote countryside areas - if in doubt, please send details and I will quote accurate price. Cash on collection also very welcome (Central London or Brighton, UK).Please note: there are some shipping/customs delays to Europe following Brexit. PHOTOSAll photos are copyright © Works of Design Ltd. Please let us know if any items are unclear or if you would like additional photos. ABOUT USWORKS OF DESIGN (eBay ID stackingsystem) is a UK based audio and design consultancy with a carefully curated selection of works for sale. +++ Please see our other vintage design and audio items !! +++

This amp has been restored, a lot of components were replaced but it still doesnt work correctly. When I powered it up, it was humming quite severely, making crackling noises and after a few minutes one of the resistors started to smoke. So, it needs the kind of attention Im not experienced enough to provide. It comes as shown with a set of valves, a Bulgin power cable and an Octal interconnect. Yes, Ill ship overseas. Please email for prices. Collection in person is welcome. If there’s no Buy It Now price displayed, there’s no Buy It Now price Unless stated, I ship overseas. If the price isn’t shown, please ask If its not shown or mentioned, its not included Please look at my other items _gsrx_vers_1516 (GS 9.3 (1516))

LEAK TL/12 Plus Mono Power Amplifier, Valve (tube) TL12+, EL84. Serviced.. Vintage Leak TL/12 PLUS 12w Mono power amplifier, Gold colour. Has been serviced with components replaced. In very good condition (see photos) Complete with valves: GZ34 (Mullard), EF86 (Mullard), ECC81 (Mullard) and 2 x EL84’s (Mazda) Also RCA lead (See photo). I have mislaid the mains lead, will send if I find it. Very nice example for collector or to match up with an existing one. Photos form part of the description. Sorry will only ship to a UK address.