Klipsch RW-8 120V Black Powered Home Theater Subwoofer - Used/tested. SPECS AMPLIFIER Class A/B Discrete (w/Switch Mode Power Supply) FTC Rated Power: 125 watts continuous @ <2%THD Dynamic Power*: 270 watts BANDWIDTH 32-120Hz 3dB MAXIMUM OUTPUT 103dB @ 30Hz 1/8 space, 1 meter LOW PASS Continuously variable from 40-120Hz CROSSOVER 24dB/octave slope above 120Hz INPUTS Two high level speaker binding posts, two line level RCA phono jacks, one line level LFE jack OUTPUTS None PHASE Continuously variable from 0-180 degrees DRIVE COMPONENTS One 8 (20.3cm) front-firing Cerametallic cone woofer

Klipsch RW-8 120V Black Powered Home Theater Subwoofer. 30 Subwoofer Cable and extra long power cable Included. Just dont need anymore. 100 operational. DESCRIPTIONBass-reflex powered design, 8 front-firing aluminum cone woofer, 190w Class A/B amplifier, 32Hz-120Hz ±3dB, 29lb.

klipsch rw-8 Subwoofer. Condition is Used.

KLIPSCH RW 8 RW8 Powered 8 Subwoofer, Front Firing - TESTED WORKS. Subwoofer is in good condition some scratches chips here and there but otherwise it’s in good working condition.Free economy shipping

Klipsch RW-8 120V Black Powered Home Theater Subwoofer - Used/tested. SPECS AMPLIFIER Class A/B Discrete (w/Switch Mode Power Supply) FTC Rated Power: 125 watts continuous @ <2%THD Dynamic Power*: 270 watts BANDWIDTH 32-120Hz 3dB MAXIMUM OUTPUT 103dB @ 30Hz 1/8 space, 1 meter LOW PASS Continuously variable from 40-120Hz CROSSOVER 24dB/octave slope above 120Hz INPUTS Two high level speaker binding posts, two line level RCA phono jacks, one line level LFE jack OUTPUTS None PHASE Continuously variable from 0-180 degrees DRIVE COMPONENTS One 8 (20.3cm) front-firing Cerametallic cone woofer

Klipsch RW-8 120V Black Powered Home Theater Subwoofer Tested Works Well Showing normal signs of wear Plastic Grill has a few broken spots - not noticeable from front If you have any questions please let me know ShippingBy default, we use USPS. A carrier will be chosen basedupon customer location, shipping price, and seller convenience. If you have special delivery instructions, please let us know prior to purchasing to make arrangements. INTERNATIONAL BUYERS SHIPPING IS CALCULATED BY EBAY GLOBAL SHIPPING SERVICE AND CHARGED BY THEMPLEASE NOTE: IMPORT DUTIES, TAXES AND CHARGES ARE NOT INCLUDED IN THE ITEM PRICE OR SHIPPING COST. THESE CHARGES ARE THE BUYERS RESPONSIBILITY.

KLIPSCH RSA-500 SUBWOOFER AMP 300W @ 8OHM 500W @4OHM. Tested and working on all inputs and outputs on a klipsch KSW15. All switches work. Both front knobs work. Basically a brand new unit. Was installed and rarely used. Cons: Power LED is not working. Power to LED is working. Light bulb appears to have died. Can replace before shipping if you like at your cost of bulb. One foot seems to have broken off. Can glue on or replace at your preference. Replaced at your cost. The rack mount ears are not included. I have a set I can add for a small fee. Guaranteed not DOA. Sold as is, no warranty. Please ask all questions before bidding. Will ship within 72hrs of payment or 72hours after any replacement parts are added. Ships from Maui, Hawaii. Appx 22lbs from zip 96753 in a box 20x20x12 International shipping ONLY through eBay international shipping service. Please message before bidding. While the RSA-500 subwoofer amplifier was primarily designed for use with the RW-5802 and RW-5101-C in-wall subwoofers, it also features custom settings for the AW-800-SW outdoor subwoofer. Features: EQ switch for use with different subwoofers Selectable signal-sensing or voltage triggered auto-on/off circuit 300 watts continuous into 8 ohms or 500 watts continuous into 4 ohms Line and speaker level inputs This high-powered device will drive up to two of any of these subwoofer modules and delivers 300 watts into an 8-ohm load (one subwoofer module) and 500 watts into a 4-ohm load (two subwoofer modules). It also comes with rack ears for fast and secure placement into any standard 19-inch rack. To keep end users from inadvertently tampering with performance levels the majority of the RSA-500’s controls are housed on its rear panel. The fuse is also included on the back for quick and easy replacement. A detachable IEC power cord allows for the simple removal and reinstallation of the entire amplifier unit. The RSA-500 was also designed to “play nice” by offering standard input/output connectivity that will support any type of system. SPECIFICATIONS: FREQUENCY RESPONSE 20Hz-1kHz ± 3dB ENCLOSURE TYPE Use only with RW-5802, RW-5101-C and AW-800-SW subwoofer enclosures (either one or two) AMPLIFIER BASH Hybrid AMPLIFIER POWERFTC Rated Power: 300W into 8 ohms, 500W into 4 ohms, 20Hz-1kHz @ <1.5% THD Dynamic Power: 875W into 8 ohms, AUTO POWER ON 2 second ON delay, 15 minute OFF delay LOW PASS CROSSOVER INPUTS Continuously variable from 40-120Hz, 2 Gold-plated speaker binding posts, 2 Gold-plated RCA phono jacks plus single LFE OUTPUTS 2 Gold-plated unfiltered RCA phono jacks plus single LFE PHASE DIMENSIONS Switchable between 0 and 180 degrees 3.5 (8.9cm) H x 17 (43.2cm) W x 12.6 (32cm) D (without rack ears) WEIGHT 18 lbs. (8.2kg) FINISH Black anodized aluminum face plate VOLTAGE 110/120 VAC 60Hz FEATURES Selectable EQ, Speaker Level In, Low voltage trigger, rack ears included Dynamic power indicates the actual power this amplifier will deliver to the woofer under normal operating conditions. While the FTC power rating indicates power available on a continuous, long-term basis, subwoofers do not rely on that type of power. Instead, the amplifier is called upon to deliver large, short-term peaks of power to be able to support the wide dynamics required by today’s digital music and movie formats. In addition to the required FTC power rating, we’ve provided the dynamic power rating as a better indication of the product’s true performance.

KLIPSCH RSA-500 SUBWOOFER AMP 300W @ 8OHM 500W @4OHM. Tested and working on all inputs and outputs on a klipsch KSW15. All switches work. Both front knobs work. Basically a brand new unit. Was installed and rarely used. Cons: Power LED is not working. Power to LED is working. Light bulb appears to have died. Can replace before shipping if you like at your cost of bulb. One foot seems to have broken off. Can glue on or replace at your preference. Replaced at your cost. The rack mount ears are not included. I have a set I can add for a small fee. Guaranteed not DOA. Sold as is, no warranty. Please ask all questions before bidding. Will ship within 72hrs of payment or 72hours after any replacement parts are added. Ships from Maui, Hawaii. Appx 22lbs from zip 96753 in a box 20x20x12 International shipping ONLY through eBay international shipping service. Please message before bidding. While the RSA-500 subwoofer amplifier was primarily designed for use with the RW-5802 and RW-5101-C in-wall subwoofers, it also features custom settings for the AW-800-SW outdoor subwoofer. Features: EQ switch for use with different subwoofers Selectable signal-sensing or voltage triggered auto-on/off circuit 300 watts continuous into 8 ohms or 500 watts continuous into 4 ohms Line and speaker level inputs This high-powered device will drive up to two of any of these subwoofer modules and delivers 300 watts into an 8-ohm load (one subwoofer module) and 500 watts into a 4-ohm load (two subwoofer modules). It also comes with rack ears for fast and secure placement into any standard 19-inch rack. To keep end users from inadvertently tampering with performance levels the majority of the RSA-500’s controls are housed on its rear panel. The fuse is also included on the back for quick and easy replacement. A detachable IEC power cord allows for the simple removal and reinstallation of the entire amplifier unit. The RSA-500 was also designed to “play nice” by offering standard input/output connectivity that will support any type of system. SPECIFICATIONS: FREQUENCY RESPONSE 20Hz-1kHz ± 3dB ENCLOSURE TYPE Use only with RW-5802, RW-5101-C and AW-800-SW subwoofer enclosures (either one or two) AMPLIFIER BASH Hybrid AMPLIFIER POWERFTC Rated Power: 300W into 8 ohms, 500W into 4 ohms, 20Hz-1kHz @ <1.5% THD Dynamic Power: 875W into 8 ohms, AUTO POWER ON 2 second ON delay, 15 minute OFF delay LOW PASS CROSSOVER INPUTS Continuously variable from 40-120Hz, 2 Gold-plated speaker binding posts, 2 Gold-plated RCA phono jacks plus single LFE OUTPUTS 2 Gold-plated unfiltered RCA phono jacks plus single LFE PHASE DIMENSIONS Switchable between 0 and 180 degrees 3.5 (8.9cm) H x 17 (43.2cm) W x 12.6 (32cm) D (without rack ears) WEIGHT 18 lbs. (8.2kg) FINISH Black anodized aluminum face plate VOLTAGE 110/120 VAC 60Hz FEATURES Selectable EQ, Speaker Level In, Low voltage trigger, rack ears included Dynamic power indicates the actual power this amplifier will deliver to the woofer under normal operating conditions. While the FTC power rating indicates power available on a continuous, long-term basis, subwoofers do not rely on that type of power. Instead, the amplifier is called upon to deliver large, short-term peaks of power to be able to support the wide dynamics required by today’s digital music and movie formats. In addition to the required FTC power rating, we’ve provided the dynamic power rating as a better indication of the product’s true performance.

Good used condition but does have scratches and marks (view pics)Good working condition Check my feedback and buy with confidence Need it quick? Ask me about fast shipping from CanadaNeed it overseas? I can ship Internationally to most locations with UPS Worldwide Expedited (Ask me for a quote)$55 shipping USA $45 Shipping Canada Shipping includes tracking and insurance

Klipsch RW-5802 Passive Subwoofer.

KLIPSCH RSA-500 SUBWOOFER AMP 300W @ 8OHM 500W @4OHM. Tested and working on all inputs and outputs on a klipsch KSW15. All switches work. Both front knobs work. Basically a brand new unit. Was installed and rarely used. Cons: Power LED is not working. Power to LED is working. Light bulb appears to have died. Can replace before shipping if you like at your cost of bulb. One foot seems to have broken off. Can glue on or replace at your preference. Replaced at your cost. The rack mount ears are not included. I have a set I can add for a small fee. Guaranteed not DOA. Sold as is, no warranty. Please ask all questions before bidding. Will ship within 72hrs of payment or 72hours after any replacement parts are added. Ships from Maui, Hawaii. Appx 22lbs from zip 96753 in a box 20x20x12 International shipping ONLY through eBay international shipping service. Please message before bidding. While the RSA-500 subwoofer amplifier was primarily designed for use with the RW-5802 and RW-5101-C in-wall subwoofers, it also features custom settings for the AW-800-SW outdoor subwoofer. Features: EQ switch for use with different subwoofers Selectable signal-sensing or voltage triggered auto-on/off circuit 300 watts continuous into 8 ohms or 500 watts continuous into 4 ohms Line and speaker level inputs This high-powered device will drive up to two of any of these subwoofer modules and delivers 300 watts into an 8-ohm load (one subwoofer module) and 500 watts into a 4-ohm load (two subwoofer modules). It also comes with rack ears for fast and secure placement into any standard 19-inch rack. To keep end users from inadvertently tampering with performance levels the majority of the RSA-500’s controls are housed on its rear panel. The fuse is also included on the back for quick and easy replacement. A detachable IEC power cord allows for the simple removal and reinstallation of the entire amplifier unit. The RSA-500 was also designed to “play nice” by offering standard input/output connectivity that will support any type of system. SPECIFICATIONS: FREQUENCY RESPONSE 20Hz-1kHz ± 3dB ENCLOSURE TYPE Use only with RW-5802, RW-5101-C and AW-800-SW subwoofer enclosures (either one or two) AMPLIFIER BASH Hybrid AMPLIFIER POWERFTC Rated Power: 300W into 8 ohms, 500W into 4 ohms, 20Hz-1kHz @ <1.5% THD Dynamic Power: 875W into 8 ohms, AUTO POWER ON 2 second ON delay, 15 minute OFF delay LOW PASS CROSSOVER INPUTS Continuously variable from 40-120Hz, 2 Gold-plated speaker binding posts, 2 Gold-plated RCA phono jacks plus single LFE OUTPUTS 2 Gold-plated unfiltered RCA phono jacks plus single LFE PHASE DIMENSIONS Switchable between 0 and 180 degrees 3.5 (8.9cm) H x 17 (43.2cm) W x 12.6 (32cm) D (without rack ears) WEIGHT 18 lbs. (8.2kg) FINISH Black anodized aluminum face plate VOLTAGE 110/120 VAC 60Hz FEATURES Selectable EQ, Speaker Level In, Low voltage trigger, rack ears included Dynamic power indicates the actual power this amplifier will deliver to the woofer under normal operating conditions. While the FTC power rating indicates power available on a continuous, long-term basis, subwoofers do not rely on that type of power. Instead, the amplifier is called upon to deliver large, short-term peaks of power to be able to support the wide dynamics required by today’s digital music and movie formats. In addition to the required FTC power rating, we’ve provided the dynamic power rating as a better indication of the product’s true performance.

KLIPSCH RSA-500 SUBWOOFER AMP 300W @ 8OHM 500W @4OHM. Tested and working on all inputs and outputs on a klipsch KSW15. All switches work. Both front knobs work. Basically a brand new unit. Was installed and rarely used. Cons: Power LED is not working. Power to LED is working. Light bulb appears to have died. Can replace before shipping if you like at your cost of bulb. One foot seems to have broken off. Can glue on or replace at your preference. Replaced at your cost. The rack mount ears are not included. I have a set I can add for a small fee. Guaranteed not DOA. Sold as is, no warranty. Please ask all questions before bidding. Will ship within 72hrs of payment or 72hours after any replacement parts are added. Ships from Maui, Hawaii. Appx 22lbs from zip 96753 in a box 20x20x12 International shipping ONLY through eBay international shipping service. Please message before bidding. While the RSA-500 subwoofer amplifier was primarily designed for use with the RW-5802 and RW-5101-C in-wall subwoofers, it also features custom settings for the AW-800-SW outdoor subwoofer. Features: EQ switch for use with different subwoofers Selectable signal-sensing or voltage triggered auto-on/off circuit 300 watts continuous into 8 ohms or 500 watts continuous into 4 ohms Line and speaker level inputs This high-powered device will drive up to two of any of these subwoofer modules and delivers 300 watts into an 8-ohm load (one subwoofer module) and 500 watts into a 4-ohm load (two subwoofer modules). It also comes with rack ears for fast and secure placement into any standard 19-inch rack. To keep end users from inadvertently tampering with performance levels the majority of the RSA-500’s controls are housed on its rear panel. The fuse is also included on the back for quick and easy replacement. A detachable IEC power cord allows for the simple removal and reinstallation of the entire amplifier unit. The RSA-500 was also designed to “play nice” by offering standard input/output connectivity that will support any type of system. SPECIFICATIONS: FREQUENCY RESPONSE 20Hz-1kHz ± 3dB ENCLOSURE TYPE Use only with RW-5802, RW-5101-C and AW-800-SW subwoofer enclosures (either one or two) AMPLIFIER BASH Hybrid AMPLIFIER POWERFTC Rated Power: 300W into 8 ohms, 500W into 4 ohms, 20Hz-1kHz @ <1.5% THD Dynamic Power: 875W into 8 ohms, AUTO POWER ON 2 second ON delay, 15 minute OFF delay LOW PASS CROSSOVER INPUTS Continuously variable from 40-120Hz, 2 Gold-plated speaker binding posts, 2 Gold-plated RCA phono jacks plus single LFE OUTPUTS 2 Gold-plated unfiltered RCA phono jacks plus single LFE PHASE DIMENSIONS Switchable between 0 and 180 degrees 3.5 (8.9cm) H x 17 (43.2cm) W x 12.6 (32cm) D (without rack ears) WEIGHT 18 lbs. (8.2kg) FINISH Black anodized aluminum face plate VOLTAGE 110/120 VAC 60Hz FEATURES Selectable EQ, Speaker Level In, Low voltage trigger, rack ears included Dynamic power indicates the actual power this amplifier will deliver to the woofer under normal operating conditions. While the FTC power rating indicates power available on a continuous, long-term basis, subwoofers do not rely on that type of power. Instead, the amplifier is called upon to deliver large, short-term peaks of power to be able to support the wide dynamics required by today’s digital music and movie formats. In addition to the required FTC power rating, we’ve provided the dynamic power rating as a better indication of the product’s true performance.

KLIPSCH RSA-500 SUBWOOFER AMP 300W @ 8OHM 500W @4OHM. Tested and working on all inputs and outputs on a klipsch KSW15. All switches work. Both front knobs work. Basically a brand new unit. Was installed and rarely used. Cons: Power LED is not working. Power to LED is working. Light bulb appears to have died. Can replace before shipping if you like at your cost of bulb. One foot seems to have broken off. Can glue on or replace at your preference. Replaced at your cost. The rack mount ears are not included. I have a set I can add for a small fee. Guaranteed not DOA. Sold as is, no warranty. Please ask all questions before bidding. Will ship within 72hrs of payment or 72hours after any replacement parts are added. Ships from Maui, Hawaii. Appx 22lbs from zip 96753 in a box 20x20x12 International shipping ONLY through eBay international shipping service. Please message before bidding. While the RSA-500 subwoofer amplifier was primarily designed for use with the RW-5802 and RW-5101-C in-wall subwoofers, it also features custom settings for the AW-800-SW outdoor subwoofer. Features: EQ switch for use with different subwoofers Selectable signal-sensing or voltage triggered auto-on/off circuit 300 watts continuous into 8 ohms or 500 watts continuous into 4 ohms Line and speaker level inputs This high-powered device will drive up to two of any of these subwoofer modules and delivers 300 watts into an 8-ohm load (one subwoofer module) and 500 watts into a 4-ohm load (two subwoofer modules). It also comes with rack ears for fast and secure placement into any standard 19-inch rack. To keep end users from inadvertently tampering with performance levels the majority of the RSA-500’s controls are housed on its rear panel. The fuse is also included on the back for quick and easy replacement. A detachable IEC power cord allows for the simple removal and reinstallation of the entire amplifier unit. The RSA-500 was also designed to “play nice” by offering standard input/output connectivity that will support any type of system. SPECIFICATIONS: FREQUENCY RESPONSE 20Hz-1kHz ± 3dB ENCLOSURE TYPE Use only with RW-5802, RW-5101-C and AW-800-SW subwoofer enclosures (either one or two) AMPLIFIER BASH Hybrid AMPLIFIER POWERFTC Rated Power: 300W into 8 ohms, 500W into 4 ohms, 20Hz-1kHz @ <1.5% THD Dynamic Power: 875W into 8 ohms, AUTO POWER ON 2 second ON delay, 15 minute OFF delay LOW PASS CROSSOVER INPUTS Continuously variable from 40-120Hz, 2 Gold-plated speaker binding posts, 2 Gold-plated RCA phono jacks plus single LFE OUTPUTS 2 Gold-plated unfiltered RCA phono jacks plus single LFE PHASE DIMENSIONS Switchable between 0 and 180 degrees 3.5 (8.9cm) H x 17 (43.2cm) W x 12.6 (32cm) D (without rack ears) WEIGHT 18 lbs. (8.2kg) FINISH Black anodized aluminum face plate VOLTAGE 110/120 VAC 60Hz FEATURES Selectable EQ, Speaker Level In, Low voltage trigger, rack ears included Dynamic power indicates the actual power this amplifier will deliver to the woofer under normal operating conditions. While the FTC power rating indicates power available on a continuous, long-term basis, subwoofers do not rely on that type of power. Instead, the amplifier is called upon to deliver large, short-term peaks of power to be able to support the wide dynamics required by today’s digital music and movie formats. In addition to the required FTC power rating, we’ve provided the dynamic power rating as a better indication of the product’s true performance.