Tested and Serviced Kenwoods mid 80s Flagship M2A Stereo power amplifier. Fully working Good condition.Serviced/ Cleaned/ testedDC offset is goodBias is per factory SpecAs the unit is vintage: No warranties are implied. All sales are final. Having said that, this unit has been tested and found Fully functional. I ran full power clipping tests into 4 ohms, no issues. Prior to clipping, I got 501 watts into both channels (Resistive load, tested with a 20Hz sinewave).Condition is quite good overall for its age. There are signs of use all over, its not perfect, but very presentable. Front looks pretty good and clean, as is the rest of the amplifier.I will accept offers of $425 if you want it sooner.

Tested and Serviced Kenwoods mid 80s Flagship M2A Stereo power amplifier. Fully working The one on this Auction is the M2a on top. I marked this with Green Check marks in the photos. Average condition for its age.Serviced/ Cleaned/ testedMeters calibrated.New Capacitors in regulated power supply. DC offset is goodBias is per factory SpecAs the unit is vintage: No warranties are implied. All sales are final. Having said that, this unit has been tested and found Fully functional. I ran full power clipping tests into 8 and 4 ohms, no issues. Prior to clipping, at 8 ohms I got 286 watts into both channels (Resistive load, tested with a 20Hz sinewave) and 487 watts into 4 ohms.Condition is quite good overall except for some pitting inside the chassis and below the unit, See photo of inside to see the pitting/ surface rusting.Front looks pretty good and clean, as is the rest of the amplifier.I will accept offers of $495 if you want it sooner.

Tested and Serviced Kenwoods mid 80s Flagship M2A Stereo power amplifier. Fully working The one on this Auction is the M2a on top. I marked this with Green Check marks in the photos. Average condition for its age.Serviced/ Cleaned/ testedMeters calibrated.New Capacitors in regulated power supply. DC offset is goodBias is per factory SpecAs the unit is vintage: No warranties are implied. All sales are final. Having said that, this unit has been tested and found Fully functional. I ran full power clipping tests into 8 and 4 ohms, no issues. Prior to clipping, at 8 ohms I got 286 watts into both channels (Resistive load, tested with a 20Hz sinewave) and 487 watts into 4 ohms.Condition is quite good overall except for some pitting inside the chassis and below the unit, See photo of inside to see the pitting/ surface rusting.Front looks pretty good and clean, as is the rest of the amplifier.I will accept offers of $495 if you want it sooner.

A very good unit! Excellent condition, Sounds fantastic, Low hours unit, I can tell by how the chassis inside looks like new, no abuse or high humidity etc. Looks very nice. Fully Tested and Serviced Kenwoods mid 80s Flagship M2A Stereo power amplifier. Works perfectly, No scratchy volume knobs or any other issues. Sounds Impressive! 1000 damping factor on this unit, Otala triple dual differential low feedback design. Very underrated. Excellent condition.Serviced/ Cleaned/ testedNew high-quality Capacitors in critical paths. Nichicon Fine Gold series in bypass with Nichicon Muse in coupling paths. Installed a total of 8 of these high-end Fine gold capacitors.DC offset is goodBias is per factory Spec Upgraded Banana Jacks installed. The stock unit has those dreaded 80s twist type connectors, I had to replace them. As the unit is vintage: No warranties are implied. All sales are final. Having said that, this unit has been tested and found Fully functional. I ran full power clipping tests into 8 and 4 ohms, no issues. Prior to clipping, at 8 ohms I got 291 watts into both channels (Resistive load, tested with a 20Hz sinewave) and 527 watts into 4 ohms.Condition is VERY good overall except for one cosmetic blemish worth mentioning, the top right corner has a 2-3mm compression blemish. See photos. And a few light scuffs. This is a very premium piece due to its condition and upgraded Speaker posts (a $150 job in its own). Hence this is not for anyone looking for a low priced M2a (I have those if you want, let me know and I will set up an auction for you). This is for someone who loves these amps and wants the best.

Created with Eselt - eBay Listing Design Editoraudiokeeper Welcome to My Audio Vintage World Created with Eselt - eBay Listing Design EditorKENWOOD BASIC M2A BASIC C2 POWER AMPLIFIER PREAMPLIFIER 100% working order The item will be well packed, so no worries at all !!! 220v model SpecificationsPower output: 220 watts per channel into 8? (stereo)Frequency response: 1Hz to 300kHzTotal harmonic distortion: 0.004%Damping factor: 1000Input sensitivity: 1VSignal to noise ratio: 120dBDimensions: 440 x 158 x 373mmWeight: 15.5kgYear: 1985 Shipping Der Artikel wird außergewöhnlich gut in einem neuen 5-lagigen Karton, reichlich Luftpolsterfolie und Schwämmen verpackt. Versand per DPD oder GLS-Kurier mit vollständiger Versicherung und Sendungsverfolgungsnummer

This Kenwood Basic M2A Home Stereo Amplifier is a great addition to any audio setup. With its sleek black design, it will blend seamlessly into any home decor. The amplifier has stereo L/R RCA audio inputs and headphone jack and raw cable speaker jacks for A + B speakers. This amplifier has been tested and is in good working condition. It comes with its original box and is perfect for anyone looking to upgrade their home audio system. Its brand, Kenwood, is well-known for producing high-quality audio equipment, and this model is no exception.

Tested and Serviced Kenwoods mid 80s Flagship M2A Stereo power amplifier. Fully working Good condition.Serviced/ Cleaned/ testedNew high-quality Capacitors in critical paths. Nichicon Fine Gold series in bypass with Nichicon Muse in coupling paths.DC offset is goodBias is per factory SpecAs the unit is vintage: No warranties are implied. All sales are final. Having said that, this unit has been tested and found Fully functional. I ran full power clipping tests into 8 and 4 ohms, no issues. Prior to clipping, at 8 ohms I got 288 watts into both channels (Resistive load, tested with a 20Hz sinewave) and 484 watts into 4 ohms.Condition is quite good overall except for the top of the fascia, there is a long band of slight discoloration, like some liquid spilled. See photos. And 2 scratches in that area.Front looks pretty good and clean, as is the rest of the amplifier.I will accept offers of $495 if you want it sooner.

Beschreibung:Wertiger Stereo Endverstärker wie im Titel benannt und original fotografiert. Läuft gut. Der abgebildete ist exakt der angebotene Power-Amplifier. Bilder zeigen den kompletten Auktionsumfang.Zustand: technisch funktionsfähig. Äusserlich Front noch ordentlich erhalten, Macke in Oberkante, Deckelblech mit Gebrauchsspuren, vgl. Bilder.Kein Versand ausserhalb Deutschland. Versand nur an die bei eBay fest hinterlegte Versandadresse! Nur DPD-Versand, Keine Packstation. No shipping outside Germany - were sorry! Sofort-Kaufen Anfragen zwecklos!English: item is running. Abholung ist nicht möglich! etope 8

Amp sounds great A + B speakers tested and working Headphone jack works Switched and Unswitched outlets working Hold buttons for graphics working Local pick up in Los Angeles or shipping via UPS Ground with signature required.

Years ago I Started Buying The Basic Series Products And Ive Decided Its Time To Let Some Of It Go. Theres Lots Of Odds And Ends Here, If Youre Looking For A M2 Or M2A Part, Good Chance Its Right Here. Good Luck And Happy Bidding. I Well Pack Everything Up Good And Tite For Shipping.

This is a very well regarded 220watts per channel power amplifier from the Glory days of the 70s and 80s. The Kenwood M2a. Condition: Excellent condition for its age. I have had dozens of M2as pass through my bench over the years for servicing, this is one of the cleaner ones. Barely much to report. There are some signs of age as you would expect, but otherwise, a very desirable condition. Id keep it if I didnt have several power amps already including 4 other M2as. Servicing: - Fully serviced/ Cleaned- DC offset adjusted. Was over 500mV when I got it, it is now set to below 3mV or 0.003volts.- Bias set to optimal levels- Controls cleaned and lubricated- Functionally there is nothing wrong with it Upgrades: I have done the following upgrades to the unit. Installed Banana Speaker binding posts. the OEM posts do not accept banana jacks, just bare wire. These ones accept bare wire, banana jacks, Spade lugs and other connectors. Installed a 2 stage fan control. OEM does only one trigger at 55c, I installed a second soft fan start if the temps exceed 45c. The fans run at very slow speed in this mode (see pic with blue arrow). If the temperature gets to 55c, the OEM thermostat kicks in and runs the fan at full speed. I could only get it to trigger the soft stage 1 after 50 minutes of loud testing with 4 ohm speakers. Installed larger rubber feet. OEMs were hard plastic..RECAPPED all signal path capacitors with a combination of WIMA (4x) and Nichicon Muse (8x) You will not find a better sounding Kenwood M2a!

Amp sounds great A + B speakers tested and working Headphone jack works Switched and Unswitched outlets working Hold buttons for graphics working Face plate has some stains /spots and a streak on graphics window. Sticker residue to the right of graphics window See pictures for best description and details

POWERS ONSHIPPING IS 50.00

Kenwood Basic M2A Verstärker Endstufe Zustand:Vollfunktionsfähig, leichte Gebrauchsspuren und Auf der Rückseite hat das Gerät einige Kratzer, bitte sehen sich die Fotos an. Lieferumfang:Kenwood Basic M2A Ware sofort lieferbar.Schneller Versand.Sollten Sie Fragen haben, schreiben Sie uns gerne eine Nachricht. Für Internationalen Versand bitte kontaktieren Sie uns.For International Shipping please contact us. VerkäuferhinweisDer angebotene Artikel wird mit Sicherheitssiegel beklebt. Diese Maßnahme dient dazu, eine Manipulation auszuschließen und eine reibungslose Rückabwicklung durchzuführen.

Kenwood Basic M2A 220 watts per channel into 8? Stereo Power Amplifier- NO SOUNDThe item up for sale is not tested for functionality as we do not have the capability to test; Unit has been inspected and the results are as follows. Intended for Reuse or Repair/Refurbishment, not for Recycling or Disposal Kenwood Basic M2A 220 watts per channel into 8? Stereo Power Amplifier- NO SOUND.The item is in C) Used, Good cosmetic condition. For cosmetic condition, please refer to the Product Grading System - Below. All ports and connectors are in good cosmetic condition.There is damage to the output terminals.The power cord is broken and loose.I was able to power on the device with an in-house power cord that is not included.The power light flashed as seen in the video and went solid, the fan did not come on.I was unable to get sound from the device.No further testing could be completed due to lack of knowledge and/or resources. The device is being sold for repair, refurbishment or reuse by the buyer. It is not intended for recycling or disposal.No accessories included.Warehouse ID: 79348 Included in the sale is: (1) Kenwood Basic M2A 220 watts per channel into 8? Stereo Power Amplifier- NO SOUNDNo accessories included Condition: For Reuse or Repair/Refurbishment See pictures for best detail *Product Grading System*A) Excellent - Looks brand new, no scuffs, no scratches, no dents or dingsB) Used, Very Good - Minor scuffs or scratches, no dents or dings C) Used, Good - Normal to heavy scuffing and scratching, a few dents or dings D) Used, Fair - Significant scuffing or scratching, several dents or dings E) Used, Poor - Extreme scuffing or scratching, extreme dents, dings Score For This Product: C) Used, Good Collectible and Specialty electronics exemption: Collectible Electronics includes items that are rare, vintage, and that are a type of device no longer manufactured or supported by original manufacturers. Specialty Electronics are rare and specialized equipment that is not generally available in retail. Return Policy: If you are not satisfied with the unit (s), you may return it for a replacement or full refund within (30) days of the receipt. This return policy does not cover ordinary wear and tear or damage caused by improper use or accidents. To initiate a return, please contact the seller through the original listing link. Recycling:Seller desires to ensure that electronic equipment is recycled in compliance with local, state, and federal laws upon reaching the end of its useful life or becoming un-useful for any reason and will accept items back at no charge. Your participation in ensuring proper recycling of the equipment is appreciated. Please help us responsibly recycle any unused parts or electronics by shipping back to us once the item has reached the end of its useful life.We appreciate your business and your effort in helping to reduce electronic waste in our landfills. Shipping:Your order will ship via FedEx or USPS and tracking numbers will be uploaded via eBay. If you do not receive your tracking number please send us a message and we will get that information for you ASAP. Smaller items can be shipped to PO Box but larger items cannot due to FedEx.Most orders will ship either the same business day or the next business day.We will do our utmost to pack and ship your item safely and quickly.If you have special needs concerning shipping, please let us know prior to purchase. Purchase Agreement:***By clicking the Accept Offer button, you understand that youre obligated to purchase the item and that you are agreeing to the sellers price and any additional terms that have been specified.***ATTENTION: Per EBAY, purchases not paid within four (4) days may be canceled.If you have any questions feel free to ask.

Kenwood Basic M2A Endstufees ist alles voll funktionstüchtig - es gibt keine Beschädigung an der Elektronikaußen am Power-Schalter fehlt die Blende - Schalter funktioniert trotzdemaugenscheinlich mit diversen Gebrauchsspuren - wie z.B. Schleif- und Kratzspurendie bereitgestellten Fotos zeigen den angebotenen Artikelaußerdem zeigen sie die Bestandteile der Lieferung!!! ohne Netzkabel !!!weitere Artikel finden Sie in meinem Shop

Kenwood Stereo Amplifier Basic M2AAllgemeinHersteller: KenwoodModell: Basic M 2 ATyp: Stereo EndverstärkerBaujahre: 1987 - 1990Hergestellt in:Farbe: SchwarzFernbedienung: neinLeistungsaufnahme: 500 WAbmessungen: 440 x 158 x 373 mm (BxHxT)Gewicht: 15,5 kgNeupreis ca.: 1.500,- DM Anschlüsse Anzahl der Eingänge:1 x Line InAnzahl der Ausgänge:2 x Lautsprecher Technische Daten Nennleistung8 Ohm: 2x 220 W RMS (20Hz - 20kHz, bei 0.004% THD)Dauerleistung (bei Klirrfaktor)8 Ohm: 2x 230 W (bei 0.7% THD, 63Hz - 12,5kHz, nach IEC/NF Norm; bei 1% THD, 1kHz, nach DIN Norm)4 Ohm: 2x 250 W (bei 1% THD, 1kHz, nach DIN Norm)Dynamikleistung8 Ohm: 2x 346 W4 Ohm: 2x 526 WGesamtklirrfaktor:0,004% bei Nennleistung (20Hz - 20kHz, 8 Ohm)0,001% bei Nennleistung (1kHz, 8 Ohm)Intermodulationsverzerrungen0.004% bei Nennleistung (60Hz:7kHz = 4:1, 8 Ohm)Dämpfungsfaktor: 1.000 (50Hz, 8 Ohm)Anstiegszeit 1,6 µSek.Eingang (Empfindlichkeit/Impedanz):1V/47kOhmFrequenzgang: 0 - 300 kHz (+0, -3dB)Signalrauschabstand:120dB (nach IHF-66)70dB (nach IEC/NF)Stereokanaltrennung: 70dB (nach IEC/NF) Besondere Ausstattungen Kanalgetrennte PegelreglerLeistungsanzeige mit Peak-Hold (abschaltbar und umschaltbar 1/3 Sek.)KopfhöreranschlussTechnischer Zustand: Vollfunktionsfähig Optischer Zustand: GebrauchtLieferumfang: Kenwood Basic M2Awie auf den Fotos Alle Fotos sind Originalfotos. Shipment to EU I/F/B 35 EuroDie ersteigerten Sachen können auch gern abgeholt werden.

KENWOOD Stereo Power Amplifier BASIC M2A. IN BUONISSIMO STATO.Lo vendo funzionante. Era di mio padre ,e lui lha usato fino alla sua scomparsa.Da allora circa 3 anni ,non è mai piu stato usato.