Description
OEM Harman Kardon AVR 3600 Remote Control For AVR3600 Receiver. The AVR 3600 remote is capable of controlling 8 devices, includingthe AVR itself and an iPod docked in the included The Bridge III.During the installation process, you may program the codes foreach of your source components into the remote. To operate acomponent, press its Selector button to change the device mode. Each Source Selector has been preprogrammed to control certaintypes of components, with only the codes specific to each brandand model changing, depending on which product code is programmed. The AUX and Cable/SAT Source Selectors may be usedfor multiple device types, depending on the first digit of the productcode. Other Source Selectors may be reassigned to other devicetypes (see Initial Setup section). AUX Source Sector: CD player product codes begin with0, 1 or 2. VCR codes begin with 3 or 4. HDTV set-top box codesbegin with 6, PVD codes begin with 7 and TiVo® set-top box codesbegin with 8. Cable/SAT Source Selector: Cable set-top box codes beginwith 0, 1 or 2, and satellite set-top box codes begin with 3 or 4. Most of the buttons on the remote have dedicated functions,although the precise codes transmitted vary depending on thedevice mode. Due to the wide variety of functions for various sourcedevices, we have included only a few of the most-often usedfunctions on the remote: alphanumeric keys, transport controls,television-channel control, menu access and power on and off. Buttons dedicated to the AVR are available at any time, even inanother device mode: AVR Power On and Off, Audio Effects, VideoModes, Surround Modes, Volume, Mute and Sleep Settings. Pressthe Setup button near the bottom of the remote to return it toAVR mode. A button’s function depends on which component is being controlled.See Table A13 in the appendix for listings of the functions for eachtype of component. IR Transmitter Lens: As buttons are pressed on theremote, infrared codes are emitted through this lens. AVR Power On Button: Press to turn on the AVR. TheMaster Power Switch on the rear panel must be on. Device Power Off Button: Press a device’s SourceSelector, then press this button to turn off the device. Device Power On Button: Press a device’s SourceSelector, then press this button to turn on the device. Mute Button: Press to mute the AVR 3600’s speaker andheadphone outputs. To end the muting, press this button, adjustthe volume, or turn off the receiver. AVR Power Off Button: Press to turn off the AVR 3600. Source Selectors: Press one of these buttons to select asource device, e.g., DVD, CD, cable TV, satellite or HDTV tuner. Thiswill also turn on the receiver and switch the remote’s device modeto operate the source. The first press of the Radio Selector switchesthe AVR to the last-used tuner band (AM, FM or SIRIUS). Each suc-cessive press changes the band. Audio Effects: Press to directly access the Audio Effectssubmenu, which allows adjustment of the AVR’s tone and otheraudio controls. See the Initial Setup section for more information. Video Modes: Press for direct access to the Video Modessubmenu, which contains picture settings to be used after you haveadjusted the picture settings on the video display or TV. See theAdvanced Functions section for more information. Surround Modes: Press to directly access the SurroundModes submenu. Select a Surround mode category: Auto Select,Virtual Surround, Stereo, Movie, Music or Video Game. The surroundmode will change when the menu line is highlighted. To change the surround mode for the selected category, press theOK Button when the menu line is highlighted and select one of theavailable surround mode options, using the 1/5Buttons. Press theOK Button, then press the Back/Exit Button to exit the SurroundModes menu and display the next higher menu in the hierarchy. See the Advanced Functions section for more information onsurround modes. Sleep Settings Button: Press to activate the sleep timer,which turns off the receiver after a programmed period of time ofup to 90 minutes. Each press increases the timer by 10 minutes,ending with the “Sleep Off” message. Volume Control: Press to raise or lower the volume. Navigation (1/57/3) and OK Buttons: Thesebuttons are used to make selections within the menu system andto operate the tuner. Alphanumeric Keys: Use these buttons to enter numbersfor radio station frequencies or to select station presets. Last Channel: When controlling a cable, satellite or HDTVset-top box or a TV, press this button to return to the previoustelevision channel. Activity: With this button, up to eleven Activities may beprogrammed to transmit a series of commands with a single press.Execute an Activity by pressing this button, then the AlphanumericKey (or the AVR Power On or Off Button) into which it was programmed.See the Advanced Functions section for more information on Activities. Back/Exit: Press to return to the previous menu or to exit themenu system. Menu Button: This button is used within the Now Playingmenu for the tuner (including SIRIUS Radio), and The Bridge III, andto display the main menu on some source devices. To display theAVR 3600’s main menu, press the Setup Button. Disc Menu: While a DVD is playing, press the DVD SourceSelector, then this button, to display the disc’s menu. Soft keys: These buttons are used with some source devices.See Table A13 in the appendix for details. They are also used witha Teletext-capable television if your broadcast, cable or satelliteprovider offers Teletext service. Channel/Page Control: When the tuner has been select-ed, this control selects a preset radio station. While operating acable, satellite or HDTV set-top box or a television, press these but-tons to change channels. Record Button: Use this button to make recordings when anaudio or video recorder is in use. Setup Button: Press to display the AVR’s Main Menu, or toswitch the remote to AVR device mode. Info Settings Button: Press to display the AVR’s InfoMenu, which contains the settings for the current source. Source Settings Button: Press a Source Selector andthen this button to display a source device’s settings menu. Zone Selector: Use this switch to select whether AVRcommands will affect the main listening area (Zone 1) or the remotezone of a multizone system (Zone 2). For normal operation, leavethe switch in the Zone 1 position. Track Skip: These buttons are used with source componentsto change tracks or chapters. Transport Controls: These buttons are used to controlsource components and The Bridge III. Light: Press to illuminate the buttons on the remote. Press itagain to turn the backlight off, or wait ten seconds after the lastbutton press for the light to turn off on its own. Learn: The AVR 3600 remote is capable of “learning” individualIR codes from the original remote that came with a source device.See page 16 in the Installation section.
| 
Live search