This is a creampuff, mint condition. I have enjoyed this amp for a couple years before I moved to another state. It has been in environmentally controlled storage since Dec 2019. I just dont have the space in my current house for a stereo system, which this was a part of in my previously larger home. It is in the original packaging with box and styrofoam. I unboxed it and it works as great as the day I packed it up. No scratches, dents, or any issues. Sounds great! This auction is just for the power amp, the preamp is separate auction.The last photo is a stock photo from Audioholics. Topology: Fully discrete, dual differential, high current, short signal path Class A/B. Number of Channels: 2 Power Output (rated power; THD 0.05%): 125 watts / channel (8 ohms; all channels driven). 200 watts / channel (4 ohms; all channels driven). Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB. Minimum Recommended Load Impedance: 4 ohms (which equals one 4 ohm load or two paralleled 8 ohm loads per channel). Frequency Response: 5 Hz to 80 kHz + 0 / - 2 dB. THD + N: < 0.03% Signal to Noise Ratio (8 Ohm load): 92 dB at 1 watt (A-weighted). 106 dB at rated power (A-weighted). Damping Factor (8 Ohm load): 500 Speaker Output Connections: Full-sized 5-way binding posts; one pair per channel x 2. Power Supply: 350 VA high current ultra-low noise toroidal power transformer. 40,000 uF of storage capacitance. Input sensitivity (for rated power; 8 Ohm load): 1.1 V (for full output; 8 ohms). Gain: 29 dB Input Connections: Unbalanced (RCA); one per channel. Input Impedance: 47 kOhms Trigger: Trigger Input: 5 - 20 V (AC or DC); < 10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 50 mA. Power Requirements: 115 VAC or 230 VAC +/- 10% @ 50 / 60 Hz (automatically detected and switched). Front Panel Controls and Indicators: Standby; push button (changes color to indicate Standby or On). Status LEDs (one per channel); illuminate blue for normal operation or red to indicate a fault (may be disabled by rear panel Status LED switch). Rear Panel Controls: AC Power switch; rocker switch (switches AC mains power). Status LEDs switch; small slide switch on left rear (disables front panel Status LEDs). Protection: The UPA-200 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions. If a fault occurs, the UPA-200 will return to Standby mode, the Standby push button will light amber, and the Status LEDs will flash red. Size: unboxed: 17 wide x 3.375 high x 16.5 deep Weight: 24 lbs (net); 32 lbs (boxed) Features: A true audiophile-quality stereo amplifier. Advanced engineering with SMD gain blocks. Wideband, short signal path, class A/B design topology. Top quality parts and construction. Real power easily drives complex loads. Heavy-duty power supply with oversized toroidal transformer. Gold plated five way binding post speaker terminals. Gold plated RCA input terminals. Classic Emotiva styling with rugged solid steel chassis. 15mm solid milled aluminum faceplate. Channel status LED’s. (which can be disabled in stealth mode). Remote trigger input and output. 115 VAC or 230 VAC with automatic detection and switching. Full protection from all common input and output fault conditions. Ship to USA only, payment due within 2 days of auctions end.

This is a creampuff, mint condition. I have enjoyed this amp for a couple years before I moved to another state. It has been in environmentally controlled storage since Dec 2019. I just dont have the space in my current house for a stereo system, which this was a part of in my previously larger home. It is in the original packaging with box and styrofoam. I unboxed it and it works as great as the day I packed it up. No scratches, dents, or any issues. Sounds great! This auction is just for the power amp, the preamp is separate auction.The last photo is a stock photo from Audioholics. Topology: Fully discrete, dual differential, high current, short signal path Class A/B. Number of Channels: 2 Power Output (rated power; THD 0.05%): 125 watts / channel (8 ohms; all channels driven). 200 watts / channel (4 ohms; all channels driven). Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB. Minimum Recommended Load Impedance: 4 ohms (which equals one 4 ohm load or two paralleled 8 ohm loads per channel). Frequency Response: 5 Hz to 80 kHz + 0 / - 2 dB. THD + N: < 0.03% Signal to Noise Ratio (8 Ohm load): 92 dB at 1 watt (A-weighted). 106 dB at rated power (A-weighted). Damping Factor (8 Ohm load): 500 Speaker Output Connections: Full-sized 5-way binding posts; one pair per channel x 2. Power Supply: 350 VA high current ultra-low noise toroidal power transformer. 40,000 uF of storage capacitance. Input sensitivity (for rated power; 8 Ohm load): 1.1 V (for full output; 8 ohms). Gain: 29 dB Input Connections: Unbalanced (RCA); one per channel. Input Impedance: 47 kOhms Trigger: Trigger Input: 5 - 20 V (AC or DC); < 10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 50 mA. Power Requirements: 115 VAC or 230 VAC +/- 10% @ 50 / 60 Hz (automatically detected and switched). Front Panel Controls and Indicators: Standby; push button (changes color to indicate Standby or On). Status LEDs (one per channel); illuminate blue for normal operation or red to indicate a fault (may be disabled by rear panel Status LED switch). Rear Panel Controls: AC Power switch; rocker switch (switches AC mains power). Status LEDs switch; small slide switch on left rear (disables front panel Status LEDs). Protection: The UPA-200 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions. If a fault occurs, the UPA-200 will return to Standby mode, the Standby push button will light amber, and the Status LEDs will flash red. Size: unboxed: 17 wide x 3.375 high x 16.5 deep Weight: 24 lbs (net); 32 lbs (boxed) Features: A true audiophile-quality stereo amplifier. Advanced engineering with SMD gain blocks. Wideband, short signal path, class A/B design topology. Top quality parts and construction. Real power easily drives complex loads. Heavy-duty power supply with oversized toroidal transformer. Gold plated five way binding post speaker terminals. Gold plated RCA input terminals. Classic Emotiva styling with rugged solid steel chassis. 15mm solid milled aluminum faceplate. Channel status LED’s. (which can be disabled in stealth mode). Remote trigger input and output. 115 VAC or 230 VAC with automatic detection and switching. Full protection from all common input and output fault conditions. Ship to USA only, payment due within 2 days of auctions end.

Emotiva UPA-200 Stereo Power Amplifier. Unit works great. Comes with power cord. Ships FEDEX, CONUS only. Worldwide shipping via ebay international shipping program.

This is a creampuff, mint condition. I have enjoyed this amp for a couple years before I moved to another state. It has been in environmentally controlled storage since Dec 2019. I just dont have the space in my current house for a stereo system, which this was a part of in my previously larger home. It is in the original packaging with box and styrofoam. I unboxed it and it works as great as the day I packed it up. No scratches, dents, or any issues. Sounds great! This auction is just for the power amp, the preamp is separate auction.The last photo is a stock photo from Audioholics. Topology: Fully discrete, dual differential, high current, short signal path Class A/B. Number of Channels: 2 Power Output (rated power; THD 0.05%): 125 watts / channel (8 ohms; all channels driven). 200 watts / channel (4 ohms; all channels driven). Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB. Minimum Recommended Load Impedance: 4 ohms (which equals one 4 ohm load or two paralleled 8 ohm loads per channel). Frequency Response: 5 Hz to 80 kHz + 0 / - 2 dB. THD + N: < 0.03% Signal to Noise Ratio (8 Ohm load): 92 dB at 1 watt (A-weighted). 106 dB at rated power (A-weighted). Damping Factor (8 Ohm load): 500 Speaker Output Connections: Full-sized 5-way binding posts; one pair per channel x 2. Power Supply: 350 VA high current ultra-low noise toroidal power transformer. 40,000 uF of storage capacitance. Input sensitivity (for rated power; 8 Ohm load): 1.1 V (for full output; 8 ohms). Gain: 29 dB Input Connections: Unbalanced (RCA); one per channel. Input Impedance: 47 kOhms Trigger: Trigger Input: 5 - 20 V (AC or DC); < 10 mA input current required. Trigger Output: 12 VDC; can drive any load up to 50 mA. Power Requirements: 115 VAC or 230 VAC +/- 10% @ 50 / 60 Hz (automatically detected and switched). Front Panel Controls and Indicators: Standby; push button (changes color to indicate Standby or On). Status LEDs (one per channel); illuminate blue for normal operation or red to indicate a fault (may be disabled by rear panel Status LED switch). Rear Panel Controls: AC Power switch; rocker switch (switches AC mains power). Status LEDs switch; small slide switch on left rear (disables front panel Status LEDs). Protection: The UPA-200 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions. If a fault occurs, the UPA-200 will return to Standby mode, the Standby push button will light amber, and the Status LEDs will flash red. Size: unboxed: 17 wide x 3.375 high x 16.5 deep Weight: 24 lbs (net); 32 lbs (boxed) Features: A true audiophile-quality stereo amplifier. Advanced engineering with SMD gain blocks. Wideband, short signal path, class A/B design topology. Top quality parts and construction. Real power easily drives complex loads. Heavy-duty power supply with oversized toroidal transformer. Gold plated five way binding post speaker terminals. Gold plated RCA input terminals. Classic Emotiva styling with rugged solid steel chassis. 15mm solid milled aluminum faceplate. Channel status LED’s. (which can be disabled in stealth mode). Remote trigger input and output. 115 VAC or 230 VAC with automatic detection and switching. Full protection from all common input and output fault conditions. Ship to USA only, payment due within 2 days of auctions end.

EMOTIVA UPA-200POWER AMPLIFIER 2-CHANNELS100 WATTS PER SIDE VERY GOOD CONDITION IF YOU HAVE ANY QUESTIONSPLEASE FEEL FREE TO ASKBEFORE BIDDING THANK YOU & GOOD LUCK

** If you have a Feedback score of 20 or less, do not purchase this, your transaction will be cancelled** **If Buyer info doesnt match with Ship To info, the transaction will be cancelled** Please read above statements and understand before purchase. Very Good condition Emotiva UPA 200. Comes with a Pangea power cord I upgraded this to. Shipping to contiguous 48, no international shipping.. Specs:Fully discrete, dual differential, high current, short signal path Class A/B. Number of Channels: 2 Power Output (rated power; THD 0.05%): 125 watts / channel (8 ohms; all channels driven). 200 watts / channel (4 ohms; all channels driven).Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB. Will ship UPS by default,or can use FedEx if you prefer. I dont use Usps. No refunds, this is being sold As-Is, as it is a older used amplifier close to 12 years old now. Buy with confidence, I have perfect feedback since 2005 Can be picked up locally to me in the DFW area, zip code 75075. Thanks.

Perfect condition. Includes power cord. $300 + $50 shipping to CONUS. No International shipping.

** If you have a Feedback score of 20 or less, do not purchase this, your transaction will be cancelled** **If Buyer info doesnt match with Ship To info, the transaction will be cancelled** Please read above statements and understand before purchase. Very Good condition Emotiva UPA 200. Comes with a Pangea power cord I upgraded this to. Shipping with insurance to contigious 48, no international shipping.. Specs:Fully discrete, dual differential, high current, short signal path Class A/B. Number of Channels: 2 Power Output (rated power; THD 0.05%): 125 watts / channel (8 ohms; all channels driven). 200 watts / channel (4 ohms; all channels driven).Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB. Will ship UPS by default, or can use FedEx if you prefer. I dont use Usps. *******************************************************Will be shipped once Ebay releases funds, usually within 5 days of purchase date. The additional days are in addition to the 3 days Ebay Allows for shipping. If you do not agree with this, dont buy it. I dont consider my items paid for, until funds are released to me by Ebay. ********************************************************* No refunds, this is being sold As-Is, as it is a older used amplifier close to 12 years old now. Buy with confidence, I have perfect feedback Can be picked up locally to me in the DFW area, zip code 75075. Thanks.

Very Good condition Emotiva UPA 200. Comes with a Pangea power cord I upgraded this to. Shipping with insurance to contigious 48, no international shipping.. Specs: Fully discrete, dual differential, high current, short signal path Class A/B. Number of Channels: 2 Power Output (rated power; THD 0.05%): 125 watts / channel (8 ohms; all channels driven). 200 watts / channel (4 ohms; all channels driven). Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB. Will ship UPS by default, , or can use FedEx if you prefer. I dont use Usps. No refunds, this is being sold As-Is and is a used Amplifier. Buy with confidence, I have perfect feedback and go the extra mile on packing when I ship something. Can be picked up locally to me in the DFW area, zip code 75075. Thanks.

Emotiva UPA-200 Stereo Power Amplifier. Item is used, but in perfect working order. 2-Channels/100 watts per side. Will ship to the continental US. Buyer pays actual shipping costs.

Emotiva UPA-200 Stereo Power Amplifier. Item is used, but in perfect working order. 2-Channels/100 watts per side. Will ship to the continental US. Buyer pays actual shipping costs.

Selling my emotiva upa200 stereo amplifier. Will ship in original box! Fully functional and shows well.

Welcome to AM WE SELL FOR YOU! Everything we sell is 100% authentic, geniune merchandise purchased through various channels. We find the deals and pass the deals on to you. All our items are stored in a safe and clean environment and packed with care!We care about your eBay experience and want you to keep shopping online and on eBay!If there is a problem with your order, please let us know we are happy to fix a mistake and we are humans!! Feel free to ask us any questions. All our items ship same day from Missouri before 2:00 PM