finale di potenza usato Crown micro-teck 2400 perfettamente funzionante..

CROWN PS-400 POWER AMPLIFIERYou are bidding on CROWN PS-400 POWER AMPLIFIER. Its in great working condition and sounds amazing. Both channels working and sound amazing. Looks great, but please remember this is used item and does have signs of being used. All lights working and all original. All connections working great. Missing box and manual. Please look at the pictures before bidding, you will get what you see in the pictures. POLICY: SELLING AS IS, NO RETURNWe ask all buyers to email us before opening a EBAY CLAIM CASEI WILL NOT ACCEPT THE ITEM BACK, IF YOU CHANGE YOUR MIND OR DO NOT LIKE THE ITEM OR DID NOT READ THE DESCRIPTION AND LOOKED AT THE PICTURES.We ask all the buyers before leaving a negative or neutral, please email us with a problem first and we will do our best to make you happy again.We care about our buyers and we only want to see them happy.WE WANT TO SEE ALL OUR BUYERS HAPPY PAYMENT: Payment must be received in 2 days, if you do not pay with in 2 days, EBAY claim will be open. LOCAL FLORIDA PICK UP ALWAYS WELCOME BY APPOINTMENT ONLY & CASH ONLY Notify us BEFORE making payment & we will send you a revised invoice without shipping charges. Allow 24hrs notice before coming by to pick up your item Available days for Pickup: M-F 12 NOON-2:30PM We are located in the CORAL SPRINGS/COCONUT CREEK/MARGATE AREA.ALL PICK UP WILL BE DONE IN PUBLIC PLACE. ALL FLORIDA BUYER: ALL FL STATE BUYERS MUST PAY 7% SALES TAX, THIS IS A LAW, IF BUYER REFUSE TO PAY SALES TAX, THAN TRANSACTION WILL BE CANCEL AND BUYER WILL BE REPORTED TO EBAY. SHIPPING: Boxing and shipping via FedEx ground to addresses in the USA continental ONLY and shipping rate is rated to all 48 state, please do not ask for the lower shipping rate. Shipping is $85 (NONE REFUNDABLE ) FEDEX DO NOT DELIVER TO PO.BOX, MUST HAVE A VALID ADDRESS.ALASKA, HAWAII & PR BUYERS must ask for the shipping rate before bidding. ATTENTION: INTERNATIONAL BIDDERSALL INTERNATIONAL BUYERS MUST USE EBAY GLOBAL SHIPPING PROGRAM, I HAVE NOTHING TO DO WITH EBAY GLOBAL SHIPPING RATE, THIS BETWEEN BUYER AND EBAY, IF YOU DO NOT LIKE THE EBAY GLOBAL SHIPPING COST THAN PLEASE DO NOT BUY THE ITEM.

Item TitleCrown Gtx4000 Record Mounted Components Junk for Parts Untested Payment Supports managed payments Please pay within 5 days after auction is finished. About Us We are located in Japan. Its our pleasure to make you happy by proposing our recommend item. If you have any questions or request about items please feel free to ask us. International Buyers - Please Note: -Import duties taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. -Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. -These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges. -We do not mark merchandise values below value or mark items as - gifts - The US and International government regulations prohibit such behavior. Thank you for your understanding.

CROWN PS-400 POWER AMPLIFIERYou are bidding on CROWN PS-400 POWER AMPLIFIER. Its in great working condition and sounds amazing. Both channels working and sound amazing. Looks great, but please remember this is used item and does have signs of being used. All lights working and all original. All connections working great. Missing box and manual. Please look at the pictures before bidding, you will get what you see in the pictures. POLICY: SELLING AS IS, NO RETURNWe ask all buyers to email us before opening a EBAY CLAIM CASEI WILL NOT ACCEPT THE ITEM BACK, IF YOU CHANGE YOUR MIND OR DO NOT LIKE THE ITEM OR DID NOT READ THE DESCRIPTION AND LOOKED AT THE PICTURES.We ask all the buyers before leaving a negative or neutral, please email us with a problem first and we will do our best to make you happy again.We care about our buyers and we only want to see them happy.WE WANT TO SEE ALL OUR BUYERS HAPPY PAYMENT: Payment must be received in 2 days, if you do not pay with in 2 days, EBAY claim will be open. LOCAL FLORIDA PICK UP ALWAYS WELCOME BY APPOINTMENT ONLY & CASH ONLY Notify us BEFORE making payment & we will send you a revised invoice without shipping charges. Allow 24hrs notice before coming by to pick up your item Available days for Pickup: M-F 12 NOON-2:30PM We are located in the CORAL SPRINGS/COCONUT CREEK/MARGATE AREA.ALL PICK UP WILL BE DONE IN PUBLIC PLACE. ALL FLORIDA BUYER: ALL FL STATE BUYERS MUST PAY 7% SALES TAX, THIS IS A LAW, IF BUYER REFUSE TO PAY SALES TAX, THAN TRANSACTION WILL BE CANCEL AND BUYER WILL BE REPORTED TO EBAY. SHIPPING: Boxing and shipping via FedEx ground to addresses in the USA continental ONLY and shipping rate is rated to all 48 state, please do not ask for the lower shipping rate. Shipping is $85 (NONE REFUNDABLE ) FEDEX DO NOT DELIVER TO PO.BOX, MUST HAVE A VALID ADDRESS.ALASKA, HAWAII & PR BUYERS must ask for the shipping rate before bidding. ATTENTION: INTERNATIONAL BIDDERSALL INTERNATIONAL BUYERS MUST USE EBAY GLOBAL SHIPPING PROGRAM, I HAVE NOTHING TO DO WITH EBAY GLOBAL SHIPPING RATE, THIS BETWEEN BUYER AND EBAY, IF YOU DO NOT LIKE THE EBAY GLOBAL SHIPPING COST THAN PLEASE DO NOT BUY THE ITEM.

Car Audio & VideoPro AudioMarine AudioLighting Karaoke Home/Portable Audio Crown XTI4002 XTI-4002 2 Channel 2400 Watt Power Amplifier with Peak Plus Limiters Providing the Ultimate in System Performance and Protection By Allowing Full Control Over Threshold, Attack, and Release --> Click Thumbnails to Enlarge Condition and Warranty Condition: AN OPEN BOX ITEM Warranty: 6 YEAR AUDIOSAVINGS Product Description Authorized Crown Audio Dealer! Input EQ 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed. Crossover Filters Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control. Output EQ 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed. Delay For signal alignment of driver; 50 mS of total delay. SubHarmonic Synth Takes the low-frequency content of the input signal and synthesizes a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type. Peakx™ Plus Limiter User defeatable limiter that allows users to control Threshold, Attack, and Release times. Presets 50 total presets, 49 of which are user-definable. Features XTI4002 2 Channe Power Amplifier RMS Power @ 2 Ohm: 1600 Watt x 2 RMS Power @ 4 Ohm: 1200 Watt x 2 RMS Power @ 8 Ohm: 650 Watt x 2 Bridge RMS Power @ 8 Ohm: 2400 Watt x 1 Bridge RMS Power @ 4 Ohm: 3200 Watt x 1 Peak Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning 3 User-defined fan mode controls - normal, early and fullspeed - for matching fan performance to a specific application New system monitoring provides software visibility of AC line voltage and power supply temperature Integrated cast-aluminum handles for easy handling and enhanced durability Locking power cord clip provides a secure connection between the amplifier and power cord Updated HiQnet Band Manager and System Architect control software Increased number of presets to a total of 30; 29 of which are user definable Performance Sensitivity (for full rated power at 4 ohms): 1.4 Vrms Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 100 dB (A weighted) Total Harmonic Distortion (THD): < 0.5% Damping Factor 20 Hz to 1 kHz: > 500 Crosstalk (below rated power): 20 kHz - 1 kHz: > 70 db Input Impedance (nominal) Balanced: 20k ohms Unbalanced: 10k ohms Maximum Input Signal: +22 dBu typical AC Line Voltage and Frequency Configurations: 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz AC Line Current(120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch): 10.5A; no more than 38W at idle Operating Temperature: 0°C to 40°C at 95% relative humidity (non-condensing) Controls Level: Two front-panel rotary level controls, one for each channel Power Switch: On/Off switch applies AC power to the amplifier Sel/Prev/Next Buttons: Three buttons near the LCD screen that are used to access menu items and front panel lockout LCD Screen: Backlit liquid crystal display that shows preset and processing status Indicators Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs) –10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip –20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power Input/Output Input Connectors: XLR, one per channel Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel Output Connectors: Two Neutrik® Speakon® NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors) HiQnet™ USB Connector: Type B, connects to HiQnet™ network Constructions Chassis: Steel Front Panel: Cast-aluminum Cooling: Proportional speed fan with front-to-rear airflow Dimensions (WxHxD): 19 x 3.5 x 12.25 Net Weight: 18.5 lbs (8.4 kg) Shipping Weight: 21.5 lbs (9.8kg) Return Policy AudioSavings Return Policy: At Audiosavings, we strongly believe in customer satisfaction and therefore offer free return shipping within 30 days of purchase on all items returned to us within the continental USA. Prior to returning merchandise, contact us and we will give you a return authorization # and a return label. You may return this item for a refund within 30 DAYS of purchase. Warranty Repair/Exchange Period: 6 YEAR If your item is defective or you want to return it for any reason within the first 30 days of when it was delivered to you; you have the following options: We will send you a pre-paid shipping label to replace the item for a brand new one. We will send you a pre-paid shipping label to exchange the item for another item of your choice. If the item you chose is more or less money we will work out the price difference with you. If you are returning a working item in used condition for a refund there will be a 20% used item fee deducted from your refund. All replacements and exchanges are free. Replacement/Processing Time: Your replacement or refund will process within 3-5 business days of when we receive the item. Please note items with physical damage un-related to shipping are not covered under warranty. Registered software cannot be returned. You MUST notify us within 48 hours if you receive an item that was damaged during shipping. Process for returning items Please email us with your eBay user ID, Item code / model #, Condition of the item, and the reason for your return. Please also indicate whether you would like a replacement, an exchange, or a refund. We will supply you with a reference number (RMA #) to put on the package which will ensure quick processing of your return. All returns require a RMA# to be returned back to our facility. Item Code: XTI4002* Home / About Us / Contact Us / Returns / FAQs Copyright © 2016 Audio Savings, All rights reserved. | eBay Template Design

CROWN PS-400 POWER AMPLIFIERYou are bidding on CROWN PS-400 POWER AMPLIFIER. Its in great working condition and sounds amazing. Both channels working and sound amazing. Looks great, but please remember this is used item and does have signs of being used. All lights working and all original. All connections working great. Missing box and manual. Please look at the pictures before bidding, you will get what you see in the pictures. POLICY: SELLING AS IS, NO RETURNWe ask all buyers to email us before opening a EBAY CLAIM CASEI WILL NOT ACCEPT THE ITEM BACK, IF YOU CHANGE YOUR MIND OR DO NOT LIKE THE ITEM OR DID NOT READ THE DESCRIPTION AND LOOKED AT THE PICTURES.We ask all the buyers before leaving a negative or neutral, please email us with a problem first and we will do our best to make you happy again.We care about our buyers and we only want to see them happy.WE WANT TO SEE ALL OUR BUYERS HAPPY PAYMENT: Payment must be received in 2 days, if you do not pay with in 2 days, EBAY claim will be open. LOCAL FLORIDA PICK UP ALWAYS WELCOME BY APPOINTMENT ONLY & CASH ONLY Notify us BEFORE making payment & we will send you a revised invoice without shipping charges. Allow 24hrs notice before coming by to pick up your item Available days for Pickup: M-F 12 NOON-2:30PM We are located in the CORAL SPRINGS/COCONUT CREEK/MARGATE AREA.ALL PICK UP WILL BE DONE IN PUBLIC PLACE. ALL FLORIDA BUYER: ALL FL STATE BUYERS MUST PAY 7% SALES TAX, THIS IS A LAW, IF BUYER REFUSE TO PAY SALES TAX, THAN TRANSACTION WILL BE CANCEL AND BUYER WILL BE REPORTED TO EBAY. SHIPPING: Boxing and shipping via FedEx ground to addresses in the USA continental ONLY and shipping rate is rated to all 48 state, please do not ask for the lower shipping rate. Shipping is $85 (NONE REFUNDABLE ) FEDEX DO NOT DELIVER TO PO.BOX, MUST HAVE A VALID ADDRESS.ALASKA, HAWAII & PR BUYERS must ask for the shipping rate before bidding. ATTENTION: INTERNATIONAL BIDDERSALL INTERNATIONAL BUYERS MUST USE EBAY GLOBAL SHIPPING PROGRAM, I HAVE NOTHING TO DO WITH EBAY GLOBAL SHIPPING RATE, THIS BETWEEN BUYER AND EBAY, IF YOU DO NOT LIKE THE EBAY GLOBAL SHIPPING COST THAN PLEASE DO NOT BUY THE ITEM.

Car Audio & VideoPro AudioMarine AudioLighting Karaoke Home/Portable Audio Crown XTI4002 XTI-4002 2 Channel 2400 Watt Power Amplifier with Peak Plus Limiters Providing the Ultimate in System Performance and Protection By Allowing Full Control Over Threshold, Attack, and Release --> Click Thumbnails to Enlarge Condition and Warranty Condition: AN OPEN BOX ITEM Warranty: 6 YEAR AUDIOSAVINGS Product Description Authorized Crown Audio Dealer! Input EQ 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed. Crossover Filters Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control. Output EQ 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed. Delay For signal alignment of driver; 50 mS of total delay. SubHarmonic Synth Takes the low-frequency content of the input signal and synthesizes a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type. Peakx™ Plus Limiter User defeatable limiter that allows users to control Threshold, Attack, and Release times. Presets 50 total presets, 49 of which are user-definable. Features XTI4002 2 Channe Power Amplifier RMS Power @ 2 Ohm: 1600 Watt x 2 RMS Power @ 4 Ohm: 1200 Watt x 2 RMS Power @ 8 Ohm: 650 Watt x 2 Bridge RMS Power @ 8 Ohm: 2400 Watt x 1 Bridge RMS Power @ 4 Ohm: 3200 Watt x 1 Peak Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning 3 User-defined fan mode controls - normal, early and fullspeed - for matching fan performance to a specific application New system monitoring provides software visibility of AC line voltage and power supply temperature Integrated cast-aluminum handles for easy handling and enhanced durability Locking power cord clip provides a secure connection between the amplifier and power cord Updated HiQnet Band Manager and System Architect control software Increased number of presets to a total of 30; 29 of which are user definable Performance Sensitivity (for full rated power at 4 ohms): 1.4 Vrms Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 100 dB (A weighted) Total Harmonic Distortion (THD): < 0.5% Damping Factor 20 Hz to 1 kHz: > 500 Crosstalk (below rated power): 20 kHz - 1 kHz: > 70 db Input Impedance (nominal) Balanced: 20k ohms Unbalanced: 10k ohms Maximum Input Signal: +22 dBu typical AC Line Voltage and Frequency Configurations: 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz AC Line Current(120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch): 10.5A; no more than 38W at idle Operating Temperature: 0°C to 40°C at 95% relative humidity (non-condensing) Controls Level: Two front-panel rotary level controls, one for each channel Power Switch: On/Off switch applies AC power to the amplifier Sel/Prev/Next Buttons: Three buttons near the LCD screen that are used to access menu items and front panel lockout LCD Screen: Backlit liquid crystal display that shows preset and processing status Indicators Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs) –10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip –20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power Input/Output Input Connectors: XLR, one per channel Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel Output Connectors: Two Neutrik® Speakon® NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors) HiQnet™ USB Connector: Type B, connects to HiQnet™ network Constructions Chassis: Steel Front Panel: Cast-aluminum Cooling: Proportional speed fan with front-to-rear airflow Dimensions (WxHxD): 19 x 3.5 x 12.25 Net Weight: 18.5 lbs (8.4 kg) Shipping Weight: 21.5 lbs (9.8kg) Return Policy AudioSavings Return Policy: At Audiosavings, we strongly believe in customer satisfaction and therefore offer free return shipping within 30 days of purchase on all items returned to us within the continental USA. Prior to returning merchandise, contact us and we will give you a return authorization # and a return label. You may return this item for a refund within 30 DAYS of purchase. Warranty Repair/Exchange Period: 6 YEAR If your item is defective or you want to return it for any reason within the first 30 days of when it was delivered to you; you have the following options: We will send you a pre-paid shipping label to replace the item for a brand new one. We will send you a pre-paid shipping label to exchange the item for another item of your choice. If the item you chose is more or less money we will work out the price difference with you. If you are returning a working item in used condition for a refund there will be a 20% used item fee deducted from your refund. All replacements and exchanges are free. Replacement/Processing Time: Your replacement or refund will process within 3-5 business days of when we receive the item. Please note items with physical damage un-related to shipping are not covered under warranty. Registered software cannot be returned. You MUST notify us within 48 hours if you receive an item that was damaged during shipping. Process for returning items Please email us with your eBay user ID, Item code / model #, Condition of the item, and the reason for your return. Please also indicate whether you would like a replacement, an exchange, or a refund. We will supply you with a reference number (RMA #) to put on the package which will ensure quick processing of your return. All returns require a RMA# to be returned back to our facility. Item Code: XTI4002* Home / About Us / Contact Us / Returns / FAQs Copyright © 2016 Audio Savings, All rights reserved. | eBay Template Design

Car Audio & VideoPro AudioMarine AudioLighting Karaoke Home/Portable Audio Crown XTI4002 XTI-4002 2 Channel 2400 Watt Power Amplifier with Peak Plus Limiters Providing the Ultimate in System Performance and Protection By Allowing Full Control Over Threshold, Attack, and Release --> Click Thumbnails to Enlarge Condition and Warranty Condition: AN OPEN BOX ITEM Warranty: 6 YEAR AUDIOSAVINGS Product Description Authorized Crown Audio Dealer! Input EQ 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed. Crossover Filters Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control. Output EQ 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed. Delay For signal alignment of driver; 50 mS of total delay. SubHarmonic Synth Takes the low-frequency content of the input signal and synthesizes a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type. Peakx™ Plus Limiter User defeatable limiter that allows users to control Threshold, Attack, and Release times. Presets 50 total presets, 49 of which are user-definable. Features XTI4002 2 Channe Power Amplifier RMS Power @ 2 Ohm: 1600 Watt x 2 RMS Power @ 4 Ohm: 1200 Watt x 2 RMS Power @ 8 Ohm: 650 Watt x 2 Bridge RMS Power @ 8 Ohm: 2400 Watt x 1 Bridge RMS Power @ 4 Ohm: 3200 Watt x 1 Peak Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning 3 User-defined fan mode controls - normal, early and fullspeed - for matching fan performance to a specific application New system monitoring provides software visibility of AC line voltage and power supply temperature Integrated cast-aluminum handles for easy handling and enhanced durability Locking power cord clip provides a secure connection between the amplifier and power cord Updated HiQnet Band Manager and System Architect control software Increased number of presets to a total of 30; 29 of which are user definable Performance Sensitivity (for full rated power at 4 ohms): 1.4 Vrms Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 100 dB (A weighted) Total Harmonic Distortion (THD): < 0.5% Damping Factor 20 Hz to 1 kHz: > 500 Crosstalk (below rated power): 20 kHz - 1 kHz: > 70 db Input Impedance (nominal) Balanced: 20k ohms Unbalanced: 10k ohms Maximum Input Signal: +22 dBu typical AC Line Voltage and Frequency Configurations: 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz AC Line Current(120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch): 10.5A; no more than 38W at idle Operating Temperature: 0°C to 40°C at 95% relative humidity (non-condensing) Controls Level: Two front-panel rotary level controls, one for each channel Power Switch: On/Off switch applies AC power to the amplifier Sel/Prev/Next Buttons: Three buttons near the LCD screen that are used to access menu items and front panel lockout LCD Screen: Backlit liquid crystal display that shows preset and processing status Indicators Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs) –10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip –20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power Input/Output Input Connectors: XLR, one per channel Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel Output Connectors: Two Neutrik® Speakon® NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors) HiQnet™ USB Connector: Type B, connects to HiQnet™ network Constructions Chassis: Steel Front Panel: Cast-aluminum Cooling: Proportional speed fan with front-to-rear airflow Dimensions (WxHxD): 19 x 3.5 x 12.25 Net Weight: 18.5 lbs (8.4 kg) Shipping Weight: 21.5 lbs (9.8kg) Return Policy AudioSavings Return Policy: At Audiosavings, we strongly believe in customer satisfaction and therefore offer free return shipping within 30 days of purchase on all items returned to us within the continental USA. Prior to returning merchandise, contact us and we will give you a return authorization # and a return label. You may return this item for a refund within 30 DAYS of purchase. Warranty Repair/Exchange Period: 6 YEAR If your item is defective or you want to return it for any reason within the first 30 days of when it was delivered to you; you have the following options: We will send you a pre-paid shipping label to replace the item for a brand new one. We will send you a pre-paid shipping label to exchange the item for another item of your choice. If the item you chose is more or less money we will work out the price difference with you. If you are returning a working item in used condition for a refund there will be a 20% used item fee deducted from your refund. All replacements and exchanges are free. Replacement/Processing Time: Your replacement or refund will process within 3-5 business days of when we receive the item. Please note items with physical damage un-related to shipping are not covered under warranty. Registered software cannot be returned. You MUST notify us within 48 hours if you receive an item that was damaged during shipping. Process for returning items Please email us with your eBay user ID, Item code / model #, Condition of the item, and the reason for your return. Please also indicate whether you would like a replacement, an exchange, or a refund. We will supply you with a reference number (RMA #) to put on the package which will ensure quick processing of your return. All returns require a RMA# to be returned back to our facility. Item Code: XTI4002* Home / About Us / Contact Us / Returns / FAQs Copyright © 2016 Audio Savings, All rights reserved. | eBay Template Design

Car Audio & VideoPro AudioMarine AudioLighting Karaoke Home/Portable Audio Crown XTI4002 XTI-4002 2 Channel 2400 Watt Power Amplifier with Peak Plus Limiters Providing the Ultimate in System Performance and Protection By Allowing Full Control Over Threshold, Attack, and Release --> Click Thumbnails to Enlarge Condition and Warranty Condition: AN OPEN BOX ITEM Warranty: 6 YEAR AUDIOSAVINGS Product Description Authorized Crown Audio Dealer! Input EQ 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed. Crossover Filters Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control. Output EQ 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed. Delay For signal alignment of driver; 50 mS of total delay. SubHarmonic Synth Takes the low-frequency content of the input signal and synthesizes a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type. Peakx™ Plus Limiter User defeatable limiter that allows users to control Threshold, Attack, and Release times. Presets 50 total presets, 49 of which are user-definable. Features XTI4002 2 Channe Power Amplifier RMS Power @ 2 Ohm: 1600 Watt x 2 RMS Power @ 4 Ohm: 1200 Watt x 2 RMS Power @ 8 Ohm: 650 Watt x 2 Bridge RMS Power @ 8 Ohm: 2400 Watt x 1 Bridge RMS Power @ 4 Ohm: 3200 Watt x 1 Peak Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning 3 User-defined fan mode controls - normal, early and fullspeed - for matching fan performance to a specific application New system monitoring provides software visibility of AC line voltage and power supply temperature Integrated cast-aluminum handles for easy handling and enhanced durability Locking power cord clip provides a secure connection between the amplifier and power cord Updated HiQnet Band Manager and System Architect control software Increased number of presets to a total of 30; 29 of which are user definable Performance Sensitivity (for full rated power at 4 ohms): 1.4 Vrms Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 100 dB (A weighted) Total Harmonic Distortion (THD): < 0.5% Damping Factor 20 Hz to 1 kHz: > 500 Crosstalk (below rated power): 20 kHz - 1 kHz: > 70 db Input Impedance (nominal) Balanced: 20k ohms Unbalanced: 10k ohms Maximum Input Signal: +22 dBu typical AC Line Voltage and Frequency Configurations: 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz AC Line Current(120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch): 10.5A; no more than 38W at idle Operating Temperature: 0°C to 40°C at 95% relative humidity (non-condensing) Controls Level: Two front-panel rotary level controls, one for each channel Power Switch: On/Off switch applies AC power to the amplifier Sel/Prev/Next Buttons: Three buttons near the LCD screen that are used to access menu items and front panel lockout LCD Screen: Backlit liquid crystal display that shows preset and processing status Indicators Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs) –10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip –20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power Input/Output Input Connectors: XLR, one per channel Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel Output Connectors: Two Neutrik® Speakon® NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors) HiQnet™ USB Connector: Type B, connects to HiQnet™ network Constructions Chassis: Steel Front Panel: Cast-aluminum Cooling: Proportional speed fan with front-to-rear airflow Dimensions (WxHxD): 19 x 3.5 x 12.25 Net Weight: 18.5 lbs (8.4 kg) Shipping Weight: 21.5 lbs (9.8kg) Return Policy AudioSavings Return Policy: At Audiosavings, we strongly believe in customer satisfaction and therefore offer free return shipping within 30 days of purchase on all items returned to us within the continental USA. Prior to returning merchandise, contact us and we will give you a return authorization # and a return label. You may return this item for a refund within 30 DAYS of purchase. Warranty Repair/Exchange Period: 6 YEAR If your item is defective or you want to return it for any reason within the first 30 days of when it was delivered to you; you have the following options: We will send you a pre-paid shipping label to replace the item for a brand new one. We will send you a pre-paid shipping label to exchange the item for another item of your choice. If the item you chose is more or less money we will work out the price difference with you. If you are returning a working item in used condition for a refund there will be a 20% used item fee deducted from your refund. All replacements and exchanges are free. Replacement/Processing Time: Your replacement or refund will process within 3-5 business days of when we receive the item. Please note items with physical damage un-related to shipping are not covered under warranty. Registered software cannot be returned. You MUST notify us within 48 hours if you receive an item that was damaged during shipping. Process for returning items Please email us with your eBay user ID, Item code / model #, Condition of the item, and the reason for your return. Please also indicate whether you would like a replacement, an exchange, or a refund. We will supply you with a reference number (RMA #) to put on the package which will ensure quick processing of your return. All returns require a RMA# to be returned back to our facility. Item Code: XTI4002* Home / About Us / Contact Us / Returns / FAQs Copyright © 2016 Audio Savings, All rights reserved. | eBay Template Design

Car Audio & VideoPro AudioMarine AudioLighting Karaoke Home/Portable Audio Crown XTI4002 XTI-4002 2 Channel 2400 Watt Power Amplifier with Peak Plus Limiters Providing the Ultimate in System Performance and Protection By Allowing Full Control Over Threshold, Attack, and Release --> Click Thumbnails to Enlarge Condition and Warranty Condition: AN OPEN BOX ITEM Warranty: 6 YEAR AUDIOSAVINGS Product Description Authorized Crown Audio Dealer! Input EQ 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed. Crossover Filters Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control. Output EQ 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed. Delay For signal alignment of driver; 50 mS of total delay. SubHarmonic Synth Takes the low-frequency content of the input signal and synthesizes a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type. Peakx™ Plus Limiter User defeatable limiter that allows users to control Threshold, Attack, and Release times. Presets 50 total presets, 49 of which are user-definable. Features XTI4002 2 Channe Power Amplifier RMS Power @ 2 Ohm: 1600 Watt x 2 RMS Power @ 4 Ohm: 1200 Watt x 2 RMS Power @ 8 Ohm: 650 Watt x 2 Bridge RMS Power @ 8 Ohm: 2400 Watt x 1 Bridge RMS Power @ 4 Ohm: 3200 Watt x 1 Peak Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning 3 User-defined fan mode controls - normal, early and fullspeed - for matching fan performance to a specific application New system monitoring provides software visibility of AC line voltage and power supply temperature Integrated cast-aluminum handles for easy handling and enhanced durability Locking power cord clip provides a secure connection between the amplifier and power cord Updated HiQnet Band Manager and System Architect control software Increased number of presets to a total of 30; 29 of which are user definable Performance Sensitivity (for full rated power at 4 ohms): 1.4 Vrms Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 100 dB (A weighted) Total Harmonic Distortion (THD): < 0.5% Damping Factor 20 Hz to 1 kHz: > 500 Crosstalk (below rated power): 20 kHz - 1 kHz: > 70 db Input Impedance (nominal) Balanced: 20k ohms Unbalanced: 10k ohms Maximum Input Signal: +22 dBu typical AC Line Voltage and Frequency Configurations: 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz AC Line Current(120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch): 10.5A; no more than 38W at idle Operating Temperature: 0°C to 40°C at 95% relative humidity (non-condensing) Controls Level: Two front-panel rotary level controls, one for each channel Power Switch: On/Off switch applies AC power to the amplifier Sel/Prev/Next Buttons: Three buttons near the LCD screen that are used to access menu items and front panel lockout LCD Screen: Backlit liquid crystal display that shows preset and processing status Indicators Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs) –10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip –20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power Input/Output Input Connectors: XLR, one per channel Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel Output Connectors: Two Neutrik® Speakon® NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors) HiQnet™ USB Connector: Type B, connects to HiQnet™ network Constructions Chassis: Steel Front Panel: Cast-aluminum Cooling: Proportional speed fan with front-to-rear airflow Dimensions (WxHxD): 19 x 3.5 x 12.25 Net Weight: 18.5 lbs (8.4 kg) Shipping Weight: 21.5 lbs (9.8kg) Click here for the Owners Manual Return Policy AudioSavings Return Policy: At Audiosavings, we strongly believe in customer satisfaction and therefore offer free return shipping within 30 days of purchase on all items returned to us within the continental USA. Prior to returning merchandise, contact us and we will give you a return authorization # and a return label. You may return this item for a refund within 30 DAYS of purchase. Warranty Repair/Exchange Period: 6 YEAR If your item is defective or you want to return it for any reason within the first 30 days of when it was delivered to you; you have the following options: We will send you a pre-paid shipping label to replace the item for a brand new one. We will send you a pre-paid shipping label to exchange the item for another item of your choice. If the item you chose is more or less money we will work out the price difference with you. If you are returning a working item in used condition for a refund there will be a 20% used item fee deducted from your refund. All replacements and exchanges are free. Replacement/Processing Time: Your replacement or refund will process within 3-5 business days of when we receive the item. Please note items with physical damage un-related to shipping are not covered under warranty. Registered software cannot be returned. You MUST notify us within 48 hours if you receive an item that was damaged during shipping. Process for returning items Please email us with your eBay user ID, Item code / model #, Condition of the item, and the reason for your return. Please also indicate whether you would like a replacement, an exchange, or a refund. We will supply you with a reference number (RMA #) to put on the package which will ensure quick processing of your return. All returns require a RMA# to be returned back to our facility. Item Code: XTI4002* Home / About Us / Contact Us / Returns / FAQs Copyright © 2016 Audio Savings, All rights reserved. | eBay Template Design

Bedienungsanleitung Crown CDi-Serie CDi 1000CDi 2000CDi 4000 Das Gerät existiert nicht mehr, aber die Unterlagen sind noch vorhanden. Falls sie jemand gebrauchen kann, müssen sie nicht entsorgt werden.

CROWN PS-400 POWER AMPLIFIERYou are bidding on CROWN PS-400 POWER AMPLIFIER. Its in great working condition and sounds amazing. Both channels working and sound amazing. Looks great, but please remember this is used item and does have signs of being used. All lights working and all original. All connections working great. Missing box and manual. Please look at the pictures before bidding, you will get what you see in the pictures. POLICY: SELLING AS IS, NO RETURNWe ask all buyers to email us before opening a EBAY CLAIM CASEI WILL NOT ACCEPT THE ITEM BACK, IF YOU CHANGE YOUR MIND OR DO NOT LIKE THE ITEM OR DID NOT READ THE DESCRIPTION AND LOOKED AT THE PICTURES.We ask all the buyers before leaving a negative or neutral, please email us with a problem first and we will do our best to make you happy again.We care about our buyers and we only want to see them happy.WE WANT TO SEE ALL OUR BUYERS HAPPY PAYMENT: Payment must be received in 2 days, if you do not pay with in 2 days, EBAY claim will be open. LOCAL FLORIDA PICK UP ALWAYS WELCOME BY APPOINTMENT ONLY & CASH ONLY Notify us BEFORE making payment & we will send you a revised invoice without shipping charges. Allow 24hrs notice before coming by to pick up your item Available days for Pickup: M-F 12 NOON-2:30PM We are located in the CORAL SPRINGS/COCONUT CREEK/MARGATE AREA.ALL PICK UP WILL BE DONE IN PUBLIC PLACE. ALL FLORIDA BUYER: ALL FL STATE BUYERS MUST PAY 7% SALES TAX, THIS IS A LAW, IF BUYER REFUSE TO PAY SALES TAX, THAN TRANSACTION WILL BE CANCEL AND BUYER WILL BE REPORTED TO EBAY. SHIPPING: Boxing and shipping via FedEx ground to addresses in the USA continental ONLY and shipping rate is rated to all 48 state, please do not ask for the lower shipping rate. Shipping is $85 (NONE REFUNDABLE ) FEDEX DO NOT DELIVER TO PO.BOX, MUST HAVE A VALID ADDRESS.ALASKA, HAWAII & PR BUYERS must ask for the shipping rate before bidding. ATTENTION: INTERNATIONAL BIDDERSALL INTERNATIONAL BUYERS MUST USE EBAY GLOBAL SHIPPING PROGRAM, I HAVE NOTHING TO DO WITH EBAY GLOBAL SHIPPING RATE, THIS BETWEEN BUYER AND EBAY, IF YOU DO NOT LIKE THE EBAY GLOBAL SHIPPING COST THAN PLEASE DO NOT BUY THE ITEM.

Bedienungsanleitung Crown CDi-Serie CDi 1000CDi 2000CDi 4000 Das Gerät existiert nicht mehr, aber die Unterlagen sind noch vorhanden. Falls sie jemand gebrauchen kann, müssen sie nicht entsorgt werden.

CROWN PS-400 POWER AMPLIFIERYou are bidding on CROWN PS-400 POWER AMPLIFIER. Its in great working condition and sounds amazing. Both channels working and sound amazing. Looks great, but please remember this is used item and does have signs of being used. All lights working and all original. All connections working great. Missing box and manual. Please look at the pictures before bidding, you will get what you see in the pictures. POLICY: SELLING AS IS, NO RETURNWe ask all buyers to email us before opening a EBAY CLAIM CASEI WILL NOT ACCEPT THE ITEM BACK, IF YOU CHANGE YOUR MIND OR DO NOT LIKE THE ITEM OR DID NOT READ THE DESCRIPTION AND LOOKED AT THE PICTURES.We ask all the buyers before leaving a negative or neutral, please email us with a problem first and we will do our best to make you happy again.We care about our buyers and we only want to see them happy.WE WANT TO SEE ALL OUR BUYERS HAPPY PAYMENT: Payment must be received in 2 days, if you do not pay with in 2 days, EBAY claim will be open. LOCAL FLORIDA PICK UP ALWAYS WELCOME BY APPOINTMENT ONLY & CASH ONLY Notify us BEFORE making payment & we will send you a revised invoice without shipping charges. Allow 24hrs notice before coming by to pick up your item Available days for Pickup: M-F 12 NOON-2:30PM We are located in the CORAL SPRINGS/COCONUT CREEK/MARGATE AREA.ALL PICK UP WILL BE DONE IN PUBLIC PLACE. ALL FLORIDA BUYER: ALL FL STATE BUYERS MUST PAY 7% SALES TAX, THIS IS A LAW, IF BUYER REFUSE TO PAY SALES TAX, THAN TRANSACTION WILL BE CANCEL AND BUYER WILL BE REPORTED TO EBAY. SHIPPING: Boxing and shipping via FedEx ground to addresses in the USA continental ONLY and shipping rate is rated to all 48 state, please do not ask for the lower shipping rate. Shipping is $85 (NONE REFUNDABLE ) FEDEX DO NOT DELIVER TO PO.BOX, MUST HAVE A VALID ADDRESS.ALASKA, HAWAII & PR BUYERS must ask for the shipping rate before bidding. ATTENTION: INTERNATIONAL BIDDERSALL INTERNATIONAL BUYERS MUST USE EBAY GLOBAL SHIPPING PROGRAM, I HAVE NOTHING TO DO WITH EBAY GLOBAL SHIPPING RATE, THIS BETWEEN BUYER AND EBAY, IF YOU DO NOT LIKE THE EBAY GLOBAL SHIPPING COST THAN PLEASE DO NOT BUY THE ITEM.

Bedienungsanleitung Crown CDi-Serie CDi 1000CDi 2000CDi 4000 Das Gerät existiert nicht mehr, aber die Unterlagen sind noch vorhanden. Falls sie jemand gebrauchen kann, müssen sie nicht entsorgt werden.

*** Sold for parts, only!!! Engineered from the bottom up for top notch performance and unmatched reliability, the Crown® CE 4000 amplifier represents the wave of the future for power amplifiers. Designed using Crown’s patented, award-winning Class I (BCA® Balanced Current Amplifier) engineering, the CE 4000 provides superior power output, increased efficiency, legendary Crown sound and extraordinary reliability. The CE 4000 not only handles but excels at 2-ohm loads. In repeated stress tests, the CE 4000 continued to perform at levels 12 dB into clip, long after the competition had shut down. Designed for the utmost in flexibility, the CE 4000 features selectable on-board high-and low-pass filter sets, so you can easily add a sub-bass system. Additional signal control is available via Crown’s optional SST (System Solution Topologies) modules, which offer a wide variety of active crossover configurations. Your choice of dual output connectors is also available: Neutrik® Speakon® plus 5-way barrier block, 5-way barrier block plus binding strip, or dual Neutrik® Speakon®.

Bedienungsanleitung Crown CDi-Serie CDi 1000CDi 2000CDi 4000 Das Gerät existiert nicht mehr, aber die Unterlagen sind noch vorhanden. Falls sie jemand gebrauchen kann, müssen sie nicht entsorgt werden.