Porte Bras pour platine Connoisseur BD-101 et parfait état.

Sugden BD1 Connoisseur Turntable Sold For Parts Or Repair - Has Low Audible Earth Hum Owned From New (1971) And Very Well Looked After Motor Good - Recent New Drive Belt SAU 2 Tonearm With Shure M75 Cartridge & Original Elliptical Shure Stylus In Very Good Condition Standard Turntable In Very Good Condition As Seen In The Photos Lid Has Some Fine Lines And Marks But Polishes Up Well And Looks Good Will Come With Original Manual & Additional Weights Etc The Turntable Will Be Very Well Packed And You Will Receive It Exactly As Seen In The Photos Overall A Very Good Sugden BD1 Turntable For Repair Or Parts Please Be Sure Of What You Are Buying As This Item Is Sold As Seen With No Returns International Buyers Please Contact Us For An Accurate Shipping Quote

A.R. Sudgen Connoisseur Bd1 Motor Parts/repair. This motor used to run but I will sell it as non working parts only. It’s been in a box for a while. The rubber has been long gone. Thanks for looking

Porte Bras pour platine Connoisseur BD-101 et parfait état.

Pieds suspensions pour platine Sugden Connoisseur BD 101 en très bon état + Visserie complète.

Pieds suspensions pour platine Sugden Connoisseur BD 101 en très bon état + Visserie complète.

Porte Bras pour platine Connoisseur BD-101 et parfait état.

Tapis pour platine disque Connoisseur BD 101 en très bon état.Diamètre:30cmEpaisseur: 4mm

A R Sugdens Connoisseur BD.1 Turntable. Vintage turntable comes with working motor & belt but does not include tone arm or cartridge. The arm board fitted has been cut to receive tone arm and there is also a spare uncut arm board. Great example of a vintage deck, nice thin wooden surround. Do not have original packaging but will be packed securely. Smoke, pet & child free environment No returns & thanks for looking

Connoisseur Bd103 Parts Lot. Parts

A.R. Sudgen Connoisseur Bd1 Motor Parts/repair. This motor used to run but I will sell it as non working parts only. It’s been in a box for a while. The rubber has been long gone. Thanks for looking

Purchased in the 1970s Switches on ok and turntable spins but is very noisy. 2 speed, 33 & 45 rpm. Shure M75 type 2 cartridge & stylus included (stylus is separate and the protective sponge is disintegrating). SAU 2 pick up arm. Groov-Kleen cleaner. Stylus pressure gadget. The plinth cover is in good condition. Needs a 3 pin plug I would prefer collection from CM11 postcode. Will post but please bear in mind I do not have the transport screws. Any questions, please ask.

.AR Sugden Connoisseur BD1 /BD2 Turntable spares in used order-BRAKE ON/OFF LEVER/TONEARMWEIGHT AND DRIVE BELT ALL TAKEN FROM A WORKING TURNTABLE 9 YEARS AGO.NO TURNTABLE ONLY SPARES AS IN PICTURE.thanks for looking-UK BIDDERS ONLY AND NO BUY IT NOW.will not ship to shipping companies or alternative addresses.please text on 07933158535 any questions

.AR Sugden Connoisseur BD1 /BD2 Turntable spares in used order-BRAKE ON/OFF LEVER/TONEARMWEIGHT AND DRIVE BELT ALL TAKEN FROM A WORKING TURNTABLE 9 YEARS AGO.NO TURNTABLE ONLY SPARES AS IN PICTURE.thanks for looking-UK BIDDERS ONLY AND NO BUY IT NOW.will not ship to shipping companies or alternative addresses.please text on 07933158535 any questions

A R Sugden Connoisseur BD1 Turntable -Spares /Repairs. Not sure about the history with this one Was in amongst a job lot of turntables I purchased Has nice oak plinth in good condition , the platter seems to be missing the rubber mat , switch is missing the main on /off lever , motor and internal circuits all present no idea of the condition Great little project if anyone has the time !

Tapis pour platine disque Connoisseur BD 101 en très bon état.Diamètre:30cmEpaisseur: 4mm

Pieds suspensions pour platine Sugden Connoisseur BD 101 en très bon état + Visserie complète.

Porte Bras pour platine Connoisseur BD-101 et parfait état.

TURNTABLE MOTOR PULLEY REMOVER and ADJUSTER for CONNOISSEUR BD1 & BD2 Hand-crafted by Williams-Sonics, my Motor Puller enables easy and safe removal of pulleys from Connoisseur BD1 and BD2 turntable motors. It will remove them quickly and safely even if they are seized on through being very tight on the motor spindle or from not being moved for many years. Removing the pulleys by hand is possible but there is the real risk that you will irrevocably damage the motors performance. The slightest bend to the spindle will take the motor out of true alignment and the effect will be heard. Unfortunately, I have encountered several motors damaged in this way. It is impossible to repair such damage. I always use a removal tool as it is just not worth risking hand pulling when replacement motors are not available on these vintage turntables. Another essential use of this removal tool is in adjusting the pulley. Connoisseur pulleys have to be aligned, often by very small amounts. Pushing the pulley too low, then too high, then too low again in an attempt to find the right place for perfect running at both 33 and 45 rpm can be difficult. Using this tool it is easy to accurately move the pulley by micro amounts to precisely tune your turntables drive system.Included with the tool is a short stainless steel tube which can be placed over the motor spindle where the spindle protrudes very high above the pulley. The tool then fits into this tube making it simple to keep both aligned until the spindle is driven flush with the pulley. The puller is supplied with important advice gained from many years of experience with these motors and pulleys.The puller is discounted when purchased together with a suspension kit, please see my other listings. Kind regards,williams-sonics

TURNTABLE MOTOR PULLEY REMOVER and ADJUSTER for CONNOISSEUR BD1 & BD2 Hand-crafted by Williams-Sonics, my Motor Puller enables easy and safe removal of pulleys from Connoisseur BD1 and BD2 turntable motors. It will remove them quickly and safely even if they are seized on through being very tight on the motor spindle or from not being moved for many years. Removing the pulleys by hand is possible but there is the real risk that you will irrevocably damage the motors performance. The slightest bend to the spindle will take the motor out of true alignment and the effect will be heard. Unfortunately, I have encountered several motors damaged in this way. It is impossible to repair such damage. I always use a removal tool as it is just not worth risking hand pulling when replacement motors are not available on these vintage turntables. Another essential use of this removal tool is in adjusting the pulley. Connoisseur pulleys have to be aligned, often by very small amounts. Pushing the pulley too low, then too high, then too low again in an attempt to find the right place for perfect running at both 33 and 45 rpm can be difficult. Using this tool it is easy to accurately move the pulley by micro amounts to precisely tune your turntables drive system.Included with the tool is a short stainless steel tube which can be placed over the motor spindle where the spindle protrudes very high above the pulley. The tool then fits into this tube making it simple to keep both aligned until the spindle is driven flush with the pulley. The puller is supplied with important advice gained from many years of experience with these motors and pulleys.The puller is discounted when purchased together with a suspension kit, please see my other listings. Kind regards,williams-sonics

TURNTABLE MOTOR PULLEY REMOVER and ADJUSTER for CONNOISSEUR BD1 & BD2 Hand-crafted by Williams-Sonics, my Motor Puller enables easy and safe removal of pulleys from Connoisseur BD1 and BD2 turntable motors. It will remove them quickly and safely even if they are seized on through being very tight on the motor spindle or from not being moved for many years. Removing the pulleys by hand is possible but there is the real risk that you will irrevocably damage the motors performance. The slightest bend to the spindle will take the motor out of true alignment and the effect will be heard. Unfortunately, I have encountered several motors damaged in this way. It is impossible to repair such damage. I always use a removal tool as it is just not worth risking hand pulling when replacement motors are not available on these vintage turntables. Another essential use of this removal tool is in adjusting the pulley. Connoisseur pulleys have to be aligned, often by very small amounts. Pushing the pulley too low, then too high, then too low again in an attempt to find the right place for perfect running at both 33 and 45 rpm can be difficult. Using this tool it is easy to accurately move the pulley by micro amounts to precisely tune your turntables drive system. Included with the tool is a short stainless steel tube which can be placed over the motor spindle where the spindle protrudes very high above the pulley. The tool then fits into this tube making it simple to keep both aligned until the spindle is driven flush with the pulley. The puller is supplied with important advice gained from many years of experience with these motors and pulleys.The puller is discounted when purchased together with a suspension kit, please see my other listings. Kind regards,williams-sonics

EARLY MOTOR SUSPENSION FOR SUGDEN CONNOISSEUR TURNTABLES Fits: ALL EARLY BD-1, BD-2-& BD2A. Cut Band Suspension for ALL EARLY BD1, BD2, BD2A. Motors. This is a very effective suspension that will fit all early motors regardless of the anti-reverse mechanisms position in your motor. This rubber is a soft natural rubber with the perfect properties and excellent resistance to oxidisation, meaning it will last. The quality and performance of suspensions made using this rubber are excellent because of the rubbers natural elasticity. I have a very limited amount of this special natural rubber with no way of obtaining further supply. Nevertheless, I am pleased to be able to offer this kit while I can for all early motors on Connoisseur BD1 & BD2 turntables. These kits are already in use by owners not able to use my web based Conversion kit. This suspension is a Cut Band Suspension, featuring an easy mounting system. It comes as an all hand-made kit which includes the following: Three natural rubber hand cut suspension bands.Six adjustable fixings for the cut bands.One williams-sonics Gold Glass drive belt matched to the cut band suspension.Three natural rubber counter tension bands (graduated in size).One natural rubber insert for your SAU2 bias weight with alignment tool.Instructions which are easy to follow and produce perfect results.I am available for support with fitting through eBay messages.The plastic suspension plate ( hanger plate) which holds the motor to the metal plinth that have a 30mm hole in the centre need no mod. The ones with 20mm diameter hole will need a small semicircle filling inside opposite the lugs, see drawing in second photo. Please note this is a hand made Cut Band Suspension not a web suspension and is designed for early motors only and will not fit later motors. For later motors see my Service kits. If you would prefer a web suspension for your early motor and your motor has its anti-reverse mechanism at its bottom see my Conversion Suspension kit. Contact me if you have any questions, I aim to provide a prompt response. It is coincidental in this period of crisis that the barriers being employed for health reasons are ones that I already use to protect myself in my workshop and have been using for the past three years. The materials I use have always been initially cleaned with isopropanol alcohol before and at various stages of my work with them. I wear a very effective industrial rubber face mask because I do not want to ingest fine rubber particles. Also I wear eye protection against any materials and machine parts that can fly towards my face. Now I wear nitrile gloves for all the processes including packing. All reseal-able plastic bags are wiped over with isopropanol. Kind regards, williams-sonics

EARLY MOTOR SUSPENSION FOR SUGDEN CONNOISSEUR TURNTABLES Fits: ALL EARLY BD-1, BD-2-& BD2A. Cut Band Suspension for ALL EARLY BD1, BD2, BD2A. Motors. This is a very effective suspension that will fit all early motors regardless of the anti-reverse mechanisms position on your motor. This rubber is a soft natural rubber with the perfect properties and excellent resistance to oxidisation, meaning it will last. The quality and performance of suspensions made using this rubber are excellent because of the rubbers natural elasticity. I have a very limited amount of this special natural rubber with no way of obtaining further supply. Nevertheless, I am pleased to be able to offer this kit while I can for all early motors on Connoisseur BD1 & BD2 turntables. These kits are already in use by owners not able to use my web based Conversion kit. This suspension is a Cut Band Suspension, featuring an easy mounting system. It comes as an all hand-made kit which includes the following: Three natural rubber hand cut suspension bands.Six adjustable fixings for the cut bands.One williams-sonics Gold Glass drive belt matched to the cut band suspension.Three natural rubber counter tension bands (graduated in size).One natural rubber insert for your SAU2 bias weight with alignment tool.Instructions which are easy to follow and produce perfect results.I am available for support with fitting through eBay messages.The plastic suspension plate ( hanger plate) which holds the motor to the metal plinth that have a 30mm hole in the centre need no mod. The ones with 20mm diameter hole will need a small semicircle filling inside opposite the lugs, see drawing in second photo. Please note this is a hand made Cut Band Suspension not a web suspension and is designed for early motors only and will not fit later motors. For later motors see my Service kits. If you would prefer a web suspension for your early motor and your motor has its anti-reverse mechanism at its bottom see my Conversion Suspension kit. Contact me if you have any questions, I aim to provide a prompt response. It is coincidental in this period of crisis that the barriers being employed for health reasons are ones that I already use to protect myself in my workshop and have been using for the past three years. The materials I use have always been initially cleaned with isopropanol alcohol before and at various stages of my work with them. I wear a very effective industrial rubber face mask because I do not want to ingest fine rubber particles. Also I wear eye protection against any materials and machine parts that can fly towards my face. Now I wear nitrile gloves for all the processes including packing. All reseal-able plastic bags are wiped over with isopropanol. Kind regards, williams-sonics

EARLY MOTOR SUSPENSION FOR SUGDEN CONNOISSEUR TURNTABLES Fits: ALL EARLY BD-1, BD-2-& BD2A. Cut Band Suspension for ALL EARLY BD1, BD2, BD2A. Motors. This is a very effective suspension that will fit all early motors regardless of the anti-reverse mechanisms position on your motor. This rubber is a soft natural rubber with the perfect properties and excellent resistance to oxidisation, meaning it will last. The quality and performance of suspensions made using this rubber are excellent because of the rubbers natural elasticity. I have a very limited amount of this special natural rubber with no way of obtaining further supply. Nevertheless, I am pleased to be able to offer this kit while I can for all early motors on Connoisseur BD1 & BD2 turntables. These kits are already in use by owners not able to use my web based Conversion kit. This suspension is a Cut Band Suspension, featuring an easy mounting system. It comes as an all hand-made kit which includes the following: Three natural rubber hand cut suspension bands.Six adjustable fixings for the cut bands.One williams-sonics Gold Glass drive belt matched to the cut band suspension.Three natural rubber counter tension bands (graduated in size).One natural rubber insert for your SAU2 bias weight with alignment tool.Instructions which are easy to follow and produce perfect results.I am available for support with fitting through eBay messages.The plastic suspension plate ( hanger plate) which holds the motor to the metal plinth that have a 30mm hole in the centre need no mod. The ones with 20mm diameter hole will need a small semicircle filling inside opposite the lugs, see drawing in second photo. Please note this is a hand made Cut Band Suspension not a web suspension and is designed for early motors only and will not fit later motors. For later motors see my Service kits. If you would prefer a web suspension for your early motor and your motor has its anti-reverse mechanism at its bottom see my Conversion Suspension kit. Contact me if you have any questions, I aim to provide a prompt response. It is coincidental in this period of crisis that the barriers being employed for health reasons are ones that I already use to protect myself in my workshop and have been using for the past three years. The materials I use have always been initially cleaned with isopropanol alcohol before and at various stages of my work with them. I wear a very effective industrial rubber face mask because I do not want to ingest fine rubber particles. Also I wear eye protection against any materials and machine parts that can fly towards my face. Now I wear nitrile gloves for all the processes including packing. All reseal-able plastic bags are wiped over with isopropanol. Kind regards, williams-sonics