Comes in very good condition and full working order

Comes in very good condition and full working order

Community V2-6BT - Demoware vom deutschen Vertrieb- technisch neuwertig- leichte Gebrauchsspuren- Rechnung mit ausgew. MwSt- 2 Jahre Gewährleistung The V2-6 is a two-way, full-range loudspeaker system suitable for use in a wide variety of fixed installations. Compact but powerful, it is ideal for distributed systems such as those found in cafés, restaurants, shopping centers and airports. When paired with a subwoofer such as the V2-210S, a V2-6 system will produce high-fidelity, broad spectrum sound that belies its modest size. The V2-6 is also an excellent choice for ancillary delay applications. When used to augment a FOH system in such venues as auditoria, theaters and houses of worship, delay loudspeakers can significantly even-out the difference in sound pressure level from the front of the room to the rear of the room. Units may be positioned for underbalcony fill, overbalcony fill, or simply placed towards the rear of the seating areas. By deploying V2-6 loudspeakers in such a manner, the system designer will have far greater control over relative levels and relative tonal response when commissioning and equalizing the installation. The V2-6 may be mounted to a wall or ceiling surface using its included yoke bracket, suspended from its M6 threaded rigging points, or installed using a third-party mounting device.An optional model with a built-in 100W autoformer with taps at 100W, 50W, 25W and 12.5W (model V2-6T) is also available from the factory.Community V2-6BT Features:DYNA-TECH™ driver protection circuitryFerrofluid-treated HF driver for improved heat dissipationCarbon Ring Cone Technology provides 30% more piston area with increased excursion capabilityRotatable square hornTerminal strip and NL4-compatible connectorsAvailable in standard black or white finishesMounting yoke included with 10° and 20° vertical standoffsOptional V2-6T autoformer model for 70V/100V applicationsCommunity V2-6BT Specifications:Loudspeaker Type: Compact two-way, full-range, trapezoidal, vented bass, user rotatable hornOperating Range: 90 Hz to 18 kHz (-10 dB)Frequency Response: 110 Hz to 16 kHz (±3 dB)Max Input Ratings: 100W continuous, 250W program28.3 volts RMS, 56.6 volts momentary peakSensitivity (1W/1m): 92 dB (100 Hz to 12.5 kHz) free spaceMaximum Output: 112 dB SPL / 118 dB SPL (peak)Nominal Impedance: 8 ohmsMinimum Impedance: 6 ohms @ 200 HzNominal –6dB Beamwidth: 90° H x 70° V (in vertical position)Crossover Frequency: 1.3 kHzRecommended Signal Processing: 100 Hz, 24 dB/octave Butterworth high pass filterDrivers:LF 1 x 6.5-inch coneHF 1 x 1-inchDriver Protection: DYNA-TECH protection circuitryInput Connection: NL4-compatible locking connector with terminal strip in parallelControls: NoneEnclosure: Trapezoidal (22.5° included angle) 18mm, 11-ply cross-laminated birchMounting/Rigging Provisions:9 x M6 threaded rigging fittings4 x M6 threaded fittings for V-HSS and third-party suspension productsFinish: Catalyzed polyester two-part paint, black or whiteGrille: Powder coated steel, black or white finishRequired Accessories: NoneSupplied Accessories:Yoke-style mounting bracket with optional 10° and 20° standoffs that allow a 10° or 20° downward or upward vertical tiltOptional Accessories:CMKIT ceiling mount kitV-HSS handle and stand socketVB-TILT tilting bracketVB-VY6 vertical yoke bracketM6EYBLTKIT 6mm eyebolt kitDimensions:Height: 15.5 inches (395 mm)Width: 9.8 inches (249 mm)Depth: 10.1 inches (258 mm)Weight (incl. bracket):19.7 lbs (8.9 kg)21.7 lbs (9.9 kg) with autoformerModel Options:V2-6B (low impedance, black finish)V2-6W (low impedance, white finish)V2-6BT (built-in autofomer for 70V100V applications, black finish)V2-6WT (built-in autofomer for 70V100V applications, white finish)

Community V2-28 Dual 8-inch 2-Way Full-Range Speaker 300W- Demoware vom deutschen Vertrieb- technisch neuwertig- leichte Gebrauchsspuren- 2 Jahre Gewährleistung- Rechnung mit ausgew. MwSt The Community V2-28 is a two-way, full-range loudspeaker system suitable for use in a wide variety of fixed installations. This versatile unit is ideal for distributed systems such as those found in cafés, restaurants, shopping centers and airports. With its powerful dual cone drivers, the V2-28 provides additional low frequency and mid-range output over that of its sister product, the V2-8. When paired with a subwoofer such as the V2-210S, a V2-28 system will produce high-fidelity, broad spectrum sound that belies its modest size. In addition to distributed systems, the V2-28 is an excellent choice for ancillary delay applications. When used to augment a front-of-house system in venues such as auditoriums, theaters and houses of worship, delay loudspeakers can significantly even out the difference in sound pressure level from the front of the room to the rear of the room. Units may be positioned for under balcony fill, over balcony fill, or simply placed towards the rear of the seating areas. By deploying V2-28 loudspeakers in such a manner, the system designer will have far greater control over relative levels and relative tonal response when commissioning and equalizing the installation.The V2-28 may be mounted to a wall or ceiling surface using its included yoke bracket, suspended from its M6 threaded rigging points, or installed using a third-party mounting device. It includes a rotatable horn design that allows optimal dispersion in either vertical or horizontal mounting positions.FeaturesHigh fidelity, broad spectrum soundRotatable horn for optimal dispersionCarbon Ring Cone Technology and DYNA-TECH protection circuitryIdeal for distributed systems or ancillary delay and fillFrequency shaded woofers for smooth vertical pattern controlSpecs

Community V2-26B Dual 6.5-inch Full-Range Speaker DJ Lautsprecher fullrange DEMOPRODUCT DESCRIPTION- Demoware vom Deutschen Vertrieb- technisch neuwertig- leichte Gebrauchsspuren- incl. Originalverpackung- 2 Jahre Gewährleistung- Rechnung mit ausgew. MwSt Community V2-26 Dual 6.5-inch Full-Range SpeakerThe V2-26 is a two-way, full-range loudspeaker system suitable for use in a wide variety of fixed installations. This versatile model is ideal for distributed systems such as those found in cafés, restaurants, shopping centers and airports. With its powerful dual cone drivers, the V2-26 provides additional low frequency and mid-range output over that of its sister product, the V2-6. When paired with a subwoofer such as the V2-210S, a V2-26 system will produce high-fidelity, broad spectrum sound that belies its modest size. In addition to distributed systems, the V2-26 is an excellent choice for ancillary delay applications. When used to augment a front-of-house system in venues such as auditoriums, theaters and houses of worship, delay loudspeakers can significantly even out the difference in sound pressure level from the front of the room to the rear of the room. Units may be positioned for under balcony fill, over balcony fill, or simply placed towards the rear of the seating areas. By deploying V2-26 loudspeakers in such a manner, the system designer will have far greater control over relative levels and relative tonal response when commissioning and equalizing the installation.The V2-26 may be mounted to a wall or ceiling surface using its included yoke bracket, suspended from its M6 threaded rigging points, or installed using a third-party mounting device. It includes a rotatable horn design that allows optimal dispersion in either vertical or horizontal mounting positions.ApplicationsHouses of worship Restaurants, pubs, cafés Shopping malls, retail environments Airports Delay fillFeaturesHigh fidelity, broad spectrum soundRotatable horn for optimal dispersionCarbon Ring Cone Technology and DYNA-TECH protection circuitryIdeal for distributed systems or ancillary delay and fillFrequency shaded woofers for smooth vertical pattern controlSpecs

- Demoware vom deutschen Vertrieb- Rechnung mit ausgew. MwSt- 2 Jahre Gewährleistung- leichte Gebrauchsspuren- incl. Originalverpackung- technisch neuwertig Community V2-1296 VERIS 2 12-inch 2-Way Speaker 200W - 90x60 DispersionThe V2-1296 is a two-way, full-range loudspeaker system suitable for use in a wide spectrum of fixed installations. Compact and extremely powerful, the V2-1296 handles applications ranging from jazz clubs and AV presentations, to rock and roll performances. Its trapezoidal design allows it to be clustered with like units, forming powerful arrays. The 90º x 60º pattern makes the V2-1296 ideal for applications requiring a wide coverage angle, such as in rooms that are wider than they are deep. The enclosure may be suspended from its M10 threaded rigging points using a variety of optional hardware from Community, or it may be installed using a third-party mounting device.The V2-1296 provides extended high frequency response, low distortion output, a tight, punchy bass response, and precise pattern control. Featuring carefully designed crossovers that provide flat acoustic power response through the critical mid-range region, and Community’s exclusive DYNA-TECH driver protection circuitry, the V2-1296 is a versatile performer for use in music and speech applications that require high quality, high power sound reinforcement at an affordable price.ApplicationsClubsTheaters AuditoriumsHouses of worship AV presentations Fitness centersFeaturesDiscreet and aesthetic trapezoidal enclosureOptimized voicing for full-range reproductionDYNA-TECH driver protection circuitryFerrofluid-treated HF driver for improved heat dissipationCarbon Ring Cone Technology provides 30% more piston area with increased excursion capability in LF driverTerminal strip and NL4-compatible connectorsMultiple bracket options offer affordable arraying solutionsIncluded in Community’s Forecaster HD ceiling distributed system softwareAvailable in standard black or white finishesSpecsLoudspeaker Type: Two-way, full-range, trapezoidal,vented bassOperating Range: 60 Hz to 18 kHz (-10 dB)Frequency Response: 90 Hz to 16 kHz (±3 dB)Max Input Ratings:200W continuous, 500W program40 volts RMS, 80 volts momentary peakSensitivity (1W/1m): 98 dB (100 Hz to 12.5 kHz) free spaceMaximum Output: 121 dB SPL / 127 dB SPL (peak)Nominal Impedance: 8 ohmsMinimum Impedance: 6.2 ohms @ 160 HzNominal –6dB Beamwidth: 90° H x 60° V (in vertical position)Crossover Frequency: 1.3 kHzRecommended Signal Processing: 60 Hz, 24 dB/octave Butterworth high pass filterDrivers:LF 1 x 12-inch coneHF 1 x 1-inchDriver Protection: DYNA-TECH protection circuitryInput Connection: NL4-compatible locking connector with terminal strip in parallelControls: NoneEnclosure: Trapezoidal (22.5° included angle) 18mm,11-ply cross-laminated birchMounting/Rigging Provisions:13 x M10 threaded rigging fittings4 x M8 threaded fittings for third-party suspension productsFinish: Catalyzed polyester two-part paint, black or whiteGrille: Powder coated steel, black or white finishRequired Accessories: NoneSupplied Accessories: NoneOptional Accessories:VB-Y12 U-shaped yoke bracketVB-VY12 vertical yoke bracketCMKIT ceiling mount kitVB-TILT tilting bracketVB-VST versatilt bracketVFKIT vertical flying kitM10EYBLTKIT 10mm eyebolt kitSTKIT seat track kitDimensions:Height: 23.9 inches (608 mm)Width: 15.4 inches (390 mm)Depth: 14.3 inches (362 mm)Weight: 38.4 lbs (17.4 kg)Model Options:V2-1296B (black finish)V2-1296W (white finish)

Community IC6-1082/96B 8 2-Way Installation Speaker, Indoor, Black Lautsprecher - Demoware vom deutschen Vertrieb- technisch neuwertig- leichte Gebrauchsspuren- incl. Originalverpackung- 2 Jahre Gewährleistung- Rechnung mit ausgew. MwSt Community IC6-1082/96 Features:Excellent LF extension and output in a very smallenclosureExceptional fidelity with elegant I SERIES aestheticsLarge, field-rotatable HF horn for smooth, consistentcoverageLow impedance (8 ohm) or 70V/100V models availableLow profile U-Bracket or Vertical Yoke available, compatible with mostthird party wall and ceiling bracketsCommunity IC6-1082/96 Specifications:Technical Specifications:Operating Mode Low Impedance or 70V/100V models Operating Environment Indoor or Weather-Resistant Outdoor Operating Range2 53 Hz to 20 kHz Nominal Beamwidth (H x V) 90° x 60°, rotatable waveguide Transducers:LF 1 x 8 (203mm) ferrite driver, 1.8 (45mm) voice coilHF 1 x 1 (25mm) exit, 1.75 (44mm) voice coil, advanced polymer diaphragm, ferrite compression driverRecommended Amplifiers 250W - 500W @ 8 ohms, (45V - 63V)Physical:Input Connection (1) Screw terminal block (5-position) Mounting Points (7) M10 threaded inserts; (4) M8 threaded inserts (rear) Weight: 25 lbs (11.3 kg) loudspeaker Dimensions: 18.75 x 10.40 x 10.63 (476 x 264 x 270 mm)

ENT-750TW - OverviewEntasys 750 Watt Autoformer - WhiteThe ENTASYS 750-watt autoformer is a step down auto-transformer for use in constant voltage distribution systems. Designated the ENT-750T, it can be used to minimize the I2R losses of long cable runs by converting the distributed high voltage, low current signal to a lower voltage, higher current signal that can effectively drive the ENTASYS column loudspeakers. The ENT-750T is available in either black or white to match the color of the ENTASYS enclosure(s). A matching autoformer mounting bracket is also included.The ENTASYS high-performance column line array loudspeaker system is designed for permanent installation in applications such as auditoriums, airports, train stations, conference centers, lecture halls, houses of worship, stadium concourses and museums. ENTASYS features a unique three-way Full-Range Column and a Low Frequency Column in the same size enclosure, offering superior performance, high output and high power handling capability in an architecturally appealing design that is weather-resistant for outdoor installations.Unlike other column products on the market, the ENTASYS system provides consistent horizontal and vertical coverage from 800 Hz to 16 kHz from a single loudspeaker.The ENTASYS line of loudspeakers features just two loudspeaker models but they are able to be configured and deployed to achieve very high SPL, exceptional sound quality and outstanding speech intelligibility. This is accomplished through the use of multiple drivers in each pass band of the loudspeaker system. Particular attention was paid to driver spacing, including the development of a patent-pending Compact Ribbon Emulator, a device that allows a line of 1-inch drivers to effectively produce a single ribbon of energy. The spacing of the drivers used in ENTASYS has been optimized for the frequency region that they reproduce to minimize the formation of grating lobes in the vertical plane.ENTASYS systems are designed to be modular. Multiple enclosures may be stacked and joined together to form larger column line arrays. The Full-Range and Low Frequency enclosures can be arranged in any order to direct the sound only where its needed, and to extend the length of the column to provide additional low frequency pattern control. This enables the sound system designer to specify the best performing configuration for a given application.Each individual enclosure features a compact 5.5 inch wide by 7.375 inch deep teardrop shaped footprint and stands 44.5 inches tall. An extremely low-profile T-Bar mounting bracket is included with each ENTASYS column for straight flush mounting. Since the connector panels are situated on the top and bottom of the modules, the assemblies can be installed virtually flush with the wall, with invisible connections between modules. The result is an attractive, cost competitive system with excellent projection and pattern consistency in both horizontal and vertical coverage. ENTASYS systems provide excellent intelligibility, feedback rejection, and wide frequency response.The only additional items required to make ENTASYS work are a high pass filter and a power amplifier. An equalizer may also be used, if desired, but is not required to deliver exceptional sound quality. EachENTASYS loudspeaker has its own internal passive crossover to provide the required filtering. An external high pass filter is recommended to allow ENTASYS to reach its maximum performance potential.

- Demoware vom deutschen Vertrieb- technisch neuwertig- leichte Gebrauchsspuren- incl. Originalverpackung- 2 Jahre Gewährleistung- Rechnung mit ausgew. MwSt The Community ENT206 is an all-weather, column array loudspeaker housed in an attractive, heavy duty extruded PVC enclosure. Double the height of the smaller ENT203, the ENT206 provides directional control at significantly lower frequencies than the ENT203, along with enough power to effectively cover much larger areas while still remaining unobtrusive. Ideally suited to applications such as music and speech reinforcement for reverberant houses of worship, hotel lobbies, assembly rooms, transit stations, indoor/outdoor swimming pools, outdoor smoking areas, bowling alleys, and much more, the ENT206 is a solid performer that belies its small size. Like the ENT203, the ENT206 also can be utilized to support larger systems for delay and area fill. The ENT206 employs six high-power LF cone drivers and two Community CRE (Compact Ribbon Emulator) HF tweeter arrays in a two-way, single-amped configuration.Community ENT206 Features:Advanced passive crossover technologyDynamic protection circuitryCompact Ribbon Emulator high frequency technology for narrow, well-behaved vertical directivity controlAll-weather construction for indoor/outdoor usageSelectable low impedance or 70V/100V operationSimple installation using the included pan-tilt mounting bracketTightly controlled vertical dispersion reduces harmful room reflectionsWide horizontal dispersion means fewer units cover a given areaClean, clear and powerful sonic output without the cost of bi-amplificationAvailable in standard black or white finishes, may also be painted to match room décorCommunity ENT206 Specifications:Loudspeaker Type: Two-way, compact column array loudspeaker, 8 Ohm or 70V/100V operationOperating Range: 120 Hz to 22 kHz (-10 dB)Frequency Response: 180 Hz to 20 kHz (-3 dB)Max Input Ratings (8 Ohm): 150W continuous, 375W program, 35 volts RMS, 69 volts momentary peakAutoformer Taps:70V: 60W, 30W, 15W, 7.5W, 3.75W 100V: 60W, 30W, 15W, 7.5WSensitivity (1W/1m): 93 dB (180 Hz - 20 kHz)Maximum Output: 115 dB SPL / 121 dB SPL (peak)Nominal Impedance: 8 OhmsMinimum Impedance: 8.1 Ohms @ 12500 HzVertical Coverage: 20° (2 kHz to 16 kHz +/-10°) @ 13mHorizontal Coverage: 140° average (1 kHz - 10 kHz +/- 20°)Crossover Frequency: 5000 HzRecommended Signal Processing: 120 Hz, 24 dB/Oct high pass filterDrivers:LF: (6) 80mm long excursion mylar drivers HF: (2) 3-element Compact Ribbon EmulatorsDriver Protection: Dynamic protection circuitryInput Connection: NL4 Speakon-type connector for low impedance operation; and 8-position terminal strip for low impedance or constant voltage operationControls: NoneEnclosure: Extruded, high gloss paintable PVCFinish: Black or whiteGrille: Dual-layer powder coated steel, black or white finishSafety Features: Built-in safety eyeboltEnvironmental: Outdoor Direct Exposure Certified IP54W per IEC529 for UV, moisture and salt sprayRequired Accessories: High pass filterSupplied Accessories: Pan-tilt bracket accommodating zero to 22.5° down-tilt and +/- 55° panning; and ABS plastic rain cover with integrated cable inlet and 1 (25.4mm) knockout for conduit ingressOptional Accessories:E200-UMK universal mounting kit E200-SAK stand adapter kitDimensions:Height: 19.9 inches (506 mm) Width: 4.62 inches (117 mm) Depth: 7.47 inches (189 mm)Weight (without bracket): 15 lbs (6.8 kg)

Price gilt für 2 Stück/ Price is for 2 pieces! - Demoware vom deutschen Vertrieb- technisch neuwertig- incl. Originalverpackung- 2 Jahre Gewährleistung- Rechnung mit ausgew. MwSt The Community Distributed Design Series DS5 is a full-range, compact, two-way system that is ideal for installations where space is at a premium. Easily outperforming loudspeakers of a larger size format, the DS5 provides high power handling, high sensitivity and realistic sound reproduction. With a modern architectural appearance that aesthetically merges well in most environments, combined with weather-resistant capability suitable for indirect outdoor use, the DS5 can be used in a wide variety of speech and music applications. It is equipped with a built-in autoformer, allowing the full loudspeaker output to be realized with 70V or 100V distribution lines. A convenient front-accessible power tap switch is hidden behind a rotatable logo. Installation is simple and flexible using the included Infin-A-Ball™ multi-angle wall mounting bracket which allows low profile mounting and precise positioning of the enclosure over a broad tilt-swivel range.Community DS5 Features:Same components and voicing as the Distributed Design ceiling loudspeaker family High efficiency, high output, high intelligibility, low distortion Paintable enclosure constructed of high-impact ABS plastic to reduce resonances Front-accessible power tap switch for selectable 8 Ohm or 70V/100V operation Infin-A-Ball™ low profile mounting bracket included Weather-resistant construction with treated drivers, two-layer powder coated grilles and protected wiring ingressCommunity DS5 Specifications:Loudspeaker Type: Two-way, full-range, coaxial surface mount loudspeaker, 8 Ohm or 70V/100V operation Operating Range*: 65 Hz - 22 kHz Frequency Response*: 80 Hz - 20 kHz (+/- 5.2 dB) Max Input Ratings (8 Ohm):100W continuous, 250W program 28 volts RMS, 63 volts momentary peakTransformer Taps:70V: 60W, 30W, 15W, 7.5W and low impedance 100V: 60W, 30W, 15WSensitivity (1W/1m)*:93 dB SPL (125 Hz to 12.5 kHz 1/3 octave bands) 91 dB SPL (250 Hz to 4 kHz speech range)Maximum Output*: 113 dB SPL / 120 dB SPL (peak 8 Ohm)Nominal Impedance: 8 Ohms Minimum Impedance: 7.5 Ohms @ 280 Hz Nominal Coverage: 130º conical (+47° / -70°, 500 Hz to 6 kHz) Axial Q / DI: 4.5 / 6.5, 500 Hz to 6 kHz Crossover Frequency: 1.6 kHz Recommended Signal Processing: 65 Hz, 24 dB/Oct high pass filter Drivers:LF: 1x 5 cone HF: 1x 1 exit compression driverDriver Protection: Self-resetting solid state circuit breaker Input Connection: 4-screw Euroblock connector for two pair of 2-wire leads (uninterrupted whether the loudspeaker is connected or not) concealed in the base of the mounting bracket; and a 2-pin Euroblock connector on the loudspeaker enclosure Controls: Front-accessible wattage / low impedance selector switch hidden behind the rotatable logo Enclosure: ABS plastic, matte finish, paintable Mounting/Rigging Provisions: Infin-A-Ball™ mounting system with hidden internal wiring Grille: Dual-layer powder coated steel Safety Features: Built-in safety cable attachment loop Environmental: IP55 rated loudspeakers, IP56 ratedconnector cover, designed to Mil Spec 810Required Accessories: Electronic high pass filter Supplied Accessories: Infin-A-Ball™ mounting bracket, Hex wrench, Flathead screwdriver Optional Accessories: DS-WMP Wall Mount Plate Dimensions (HxWxD): 12.9 x 6.3 x 7.5 (328 x 160 x 191 mm) Weight:Without bracket: 10.3 lbs (4.7 kg) With bracket: 10.8 lbs (4.9 kg)*NOTE: On-wall pink noise measurement at 6ft (1.8m) at 10% power; extrapolated to 1 meter and an input of 2.83 volts RMS.

The proprietary Tru-Phase™ waveguide and perfectly centered driver produce a consistently wide conical polar response up to 16 kHz.Price gilt für 2 Stück/ Price is for 2 pieces! - Demoware vom deutschen Vertrieb- technisch neuwertig- leichte Gebrauchsspuren- 2 Jahre Gewährleistung- incl. Originalverpackung- Rechnung mit ausgew. MwSt FeaturesTrue coaxial loudspeaker with HF compression driverPatented Carbon Ring Cone Technology™Simple spring loaded Drop-Stop™ installationSelectable 8 Ohm or 70V/100V operation with tapsTypically requires half the usual power due to the true Coaxial design

Price gilt für 2 Stück/ Price is for 2 pieces! Community D5 5 2-Way High Output Ceiling Speaker Deckeneinbaulautsprecher 2 pcs - Demoware vom deutschen Vertrieb- technisch neuwertig- leichte Gebrauchsspuren- Rechnung mit ausgew. MwSt- 2 Jahre Gewährleistung- incl. Originalverpackung Easily fitting locations where larger models cannot, Communitys Distributed Design Series D5 provides designers and installers with an exciting new tool for high-end ceiling-mount loudspeaker systems. This innovative product provides performance normally associated with 6-inch or larger models, at a 4-inch budget. The D5’s capabilities include powerful, clear paging, background music, and mid-level foreground music, while uniform voicing technology makes it easy to combine the D5 with other members of the Distributed Design product family. The D5 is particularly effective when augmented with the D10SUB or larger full-range models in the series.True coaxial design boasts separate magnets for the LF and HF drivers for reduced distortion and industry-leading sensitivity. Providing 3 dB to 6 dB greater output level than competing products, the D5 typically requires only half the amplification power. The proprietary Tru-Phase™ waveguide and perfectly centered driver produce a consistently wide conical polar response up to 16 kHz. Community’s patented Carbon Ring Cone Technology™ increases the effective cone area to further reduce distortion while reinforcing the cone for improved durability.Exclusive Drop-Stop™ and Twist-Assist™ tabs allow single-handed placement to speed installation and reduce labor time. Drop-Stop’s spring-loaded legs support the back can on the included tile rails and snap-on C-ring, so that the installer no longer needs to hold the can against the tile while tightening the clamps. Twist-Assist performs a similar function for the baffle assembly: when the loudspeaker back cans are pre-installed into a conduit system for termination at a later date, a simple twist of the baffle into the back can brings the Twist-Assist clips together, supporting the baffle assembly while the installer fastens the screws.The front-face wattage selector switch enables quick adjustment of 70V/100V tap levels. A variety of installation accessories are available to accommodate different ceiling materials. The D5 face-only assembly and back can are also available for separate purchase.Community D5 Features:High intelligibility with exceptional uniform coverageConsistent, wide dispersion up to 16 kHzTrue coaxial loudspeakers with HF compression driversTru-Phase™ high-frequency waveguidePatented Carbon Ring Cone Technology™Spring loaded Drop-Stop™ installation assistant tabs support the back can on the included rails and C-ring to simplify installationUniquely designed tile bridge support rails and snap-on C-ring support plates prevent sagTwist-Assist™ loudspeaker face retainer tabs for fast and easy installation3/4 and 1 knock-outs on the sides of the back canExternal loop-through Euroblock connectorsRear cover with integrated cable clamp (strain relief) and optional conduit knockoutSelectable 8 Ohm or 70V/100V operationBack can and face-only packages availableFive year warrantyCommunity D5 Specifications:Loudspeaker Type: Two-way, full-range, coaxial ceiling loudspeaker, 8 Ohm or 70V/100V operationOperating Range: 65 Hz - 22 kHzFrequency Response: 80 Hz - 20 kHz (+/- 5 dB)Max Input Ratings (8 Ohm): 100W continuous, 250W program, 28 volts RMS, 63 volts momentary peakTransformer Taps:70V: 60W, 30W, 15W, 7.5W and low impedance100V: 60W, 30W, 15WDistortion:500 Hz, 10% Full Power: 2.28% 2nd Harmonic, 0.43% 3rd Harmonic500 Hz, 1% Full Power: 1.12% 2nd Harmonic, 0.42% 3rd Harmonic2 kHz, 10% Full Power: 1.14% 2nd Harmonic, 0.35% 3rd Harmonic2 kHz, 1% Full Power: 0.30% 2nd Harmonic, 0.15% 3rd Harmonic8 kHz, 10% Full Power: 0.48% 2nd Harmonic, 0.01% 3rd Harmonic8 kHz, 1% Full Power: 0.16% 2nd Harmonic, 0.03% 3rd HarmonicSensitivity (1W/1m): 93 dB SPL (125 Hz to 12.5 kHz 1/3 octave bands); 91 dB SPL (250 Hz to 4 kHz speech range)Maximum Output: 113 dB SPL / 119 dB SPL (peak 8 Ohm)Nominal Impedance: 8 OhmsMinimum Impedance: 6.9 Ohms @ 250 HzNominal Coverage: 115º conical (1 kHz to 6 kHz); 130º conical (500 Hz to 6 kHz)Axial Q / DI: 4.5 / 6.5, 500 Hz to 6 kHzCrossover Frequency: 1.6 kHzRecommended Signal Processing: 65 Hz high pass filterDrivers: LF 1x 5, HF 1x 1 exit compression driverDriver Protection: Self-resetting solid state circuit breakerInput Connection: 4-position Euroblock connectorControls: Front-face wattage / low impedance selector switchEnclosure: Corrosion-resistant zinc plated steelMounting/Rigging Provisions: 4 steel mounting clamps with 3-inch grip rangeGrille: Powder coated steel with safety line, white finish, paintableBaffle: Reflex loaded UL 94V-0 rated ABSSafety Features: 4x safety hang pointsSafety Agency Ratings: ETL listed to comply with UL1480, UL2043 and CSA60065. Suitable for use in air handling spaces per NFPA 70 and NFPA 90.Face-Only / Back Can Options: D5-FO Face-Only Assembly, D45-BC Back CanRequired Accessories: Electronic high pass filterSupplied Accessories: C-Ring supporting plate, tile support bridge rails, grille, paint mask, cut-out template, flat screwdriverOptional Accessories:D45-FAR Face Adapter RingD45-CATR Can Adapter Ring / Trim RingD45-NCB New Construction BracketDimensions:Width: 9.768 (248.1 mm) bezel diameterDepth: 6.788 (172.4 mm) can depthCutout Diameter: 8.75 (222 mm)Weight: 10.4 lbs (4.7 kg)

Price gilt für 2 Stück/ Price is for 2 pieces!- Demoware vom deutschen Vertrieb- technisch neuwertig- leichte Gebrauchsspuren- 2 Jahre Gewährleistung- Rechnung mit ausgew. MwSt The Community D4LP is a specialty loudspeaker built shallower than competing products, thus enabling its use in confined spaces, while still providing the full range of features common to all members of the Distributed Design Series. Only 3.4 inches in depth, the D4LP solves space problems that competing products cannot. Suitable for paging, background music, and to augment larger models, the D4LP is a solid performer. Characteristics are similar to the D4 with only a minor amount of bass reduction. It installs quickly and provides exceptionally uniform coverage with excellent sonic properties. Uniform voicing among the Distributed Design product family makes it easy to match the D4LP to larger models in the series. Featuring genuine coaxial design with separate magnets for the LF and HF drivers, the D4LP exhibits reduced distortion and industry-leading sensitivity permitting 3 dB to 6 dB greater output level, while requiring half the amplification power of competing products.The proprietary Tru-Phase™ waveguide and perfectly centered driver produce a consistently wide conical polar response up to 16 kHz. Community’s patented Carbon Ring Cone Technology™ increases the effective cone area to further reduce distortion while reinforcing the cone for improved durability.Community D4LP Features:High intelligibility with exceptional uniform coverageConsistent, wide dispersion up to 16 kHzTrue coaxial loudspeakers with HF compression driversTru-Phase™ high-frequency waveguidePatented Carbon Ring Cone Technology™Spring loaded Drop-Stop™ installation assistant tabs support the back can on the included rails and C-ring to simplify installationUniquely designed tile bridge support rails andsnap-on C-ring support plates prevent sagTwist-Assist™ loudspeaker face retainer tabs for fastand easy installation3/4 and 1 knock-outs on the sides of the back canExternal loop-through Euroblock connectorsRear cover with integrated cable clamp (strain relief) and optional conduit knockoutSelectable 8 Ohm or 70V/100V operationBack can and face-only packages availableFive year warrantyCommunity D4LP Specifications:Loudspeaker Type: Two-way, full-range, coaxial ceiling loudspeaker, 8 Ohm or 70V/100V operationOperating Range: 90 Hz - 18.5 kHzFrequency Response: 120 Hz - 16 kHz (+/- 5dB)Max Input Ratings (8 Ohm): 60W continuous, 150W program; 22 volts RMS, 49 volts momentary peakTransformer Taps:70V: 30W, 15W, 7.5W, 3.75W and low impedance100V: 30W, 15W, 7.5WDistortion:500 Hz, 10% Full Power: 0.18% 2nd Harmonic, 0.80% 3rd Harmonic500 Hz, 1% Full Power: 0.16% 2nd Harmonic, 0.27% 3rd Harmonic2 kHz, 10% Full Power: 1.21% 2nd Harmonic, 0.39% 3rd Harmonic2 kHz, 1% Full Power: 0.38% 2nd Harmonic, 0.28% 3rd Harmonic8 kHz, 10% Full Power: 0.38% 2nd Harmonic, 0.13% 3rd Harmonic8 kHz, 1% Full Power: 0.22% 2nd Harmonic, 0.16% 3rd HarmonicSensitivity (1W/1m): 92 dB SPL (120 Hz to 12.5 kHz1/3 octave bands); 93 dB SPL (250 Hz to 4 kHz speech range)Maximum Output: 110 dB SPL / 116 dB SPL (peak 8Ohm)Nominal Impedance: 8 OhmsMinimum Impedance: 7.8 Ohms @ 260 HzNominal Coverage: 130º conical (1 kHz to 6kHz); 140º conical (500 Hz to 6 kHz)Axial Q / DI: 4 / 6, 500 Hz to 6 kHzCrossover Frequency: 2 kHzRecommended Signal Processing: 90 Hz highpass filterDrivers: LF 1x 4.5, HF 1x 3/4 exit compression driverDriver Protection: Self-resetting solid state circuit breakerInput Connection: 4-position Euroblock connectorControls: Front-face wattage / low impedance selector switchEnclosure: Corrosion-resistant zinc plated steelMounting/Rigging Provisions: 3 steel mounting clamps with 3 grip rangeGrille: Powder coated steel with safety line,white finish, paintableBaffle: Reflex loaded UL 94V-0 rated ABSSafety Features: 3x safety hang pointsSafety Agency Ratings: ETL listed to comply with UL1480, UL2043 and CSA60065. Suitable for use in air handling spaces perNFPA 70 and NFPA 90.Face-Only / Back Can Options: D4-FO Face-Only Assembly, D45-BC Back CanRequired Accessories: Electronic high passfilterSupplied Accessories: C-Ring supporting plate,tile support bridge rails, grille, paint mask, cut-out template, flat screwdriverOptional Accessories:D45-FAR Face Adapter RingD45-CATR Can Adapter Ring / Trim RingD45-NCB New Construction BracketDimensions:Width: 9.768 (248.1 mm) bezel diameterDepth: 3.599 (172.4 mm) can depthCutout Diameter: 8.75 (222 mm)Weight: 6.6 lbs (3 kg)

Price gilt für 2 Stück/ Price is for 2 pieces! - Demoware vom deutschen Vertrieb - technisch neuwertig- incl. Originalverpackung- 2 Jahre Gewährleistung- Rechnung mit ausgew. MwSt The smallest member of Communitys Distributed Design Series, the D4 possesses the advanced features of its larger siblings with performance that belies its small size. Suitable for paging, background music, or to augment larger systems, the D4 is a versatile performer. It installs quickly and provides exceptionally uniform coverage with excellent sonic properties.Uniform voicing among the Distributed Design product family makes for an easy match to the other models in the series, while a host of design innovations set the D4 apart from other products in its size and price range. Featuring genuine coaxial design with separate magnets for the LF and HF drivers, the D4 exhibits reduced distortion and industry-leading sensitivity permitting 3 dB to 6 dB greater output level, while requiring half the amplification power of competing products.The proprietary Tru-Phase™ waveguide and perfectly centered driver produce a consistently wide conical polar response up to 16 kHz. Community’s patented Carbon Ring Cone Technology™ increases the effective cone area to further reduce distortion while reinforcing the cone for improved durability.Exclusive Drop-Stop™ and Twist-Assist™ tabs allow single-handed placement to speed installation and reduce labor time. Drop-Stop’s spring-loaded legs support the back can on the included tile rails and snap-on C-ring, so that the installer no longer needs to hold the can against the tile while tightening the clamps. Twist-Assist performs a similar function for the baffle assembly: when the loudspeaker back cans are pre-installed into a conduit system for termination at a later date, a simple twist of the baffle into the back can brings the Twist-Assist clips together, supporting the baffle assembly while the installer fastens the screws.The front-face wattage selector switch enables quick adjustment of 70V/100V tap levels. A variety of installation accessories are available to accommodate different ceiling materials. The D4 face-only assembly and back can are also available for separate purchase.Community D4 Features:High intelligibility with exceptional uniform coverageConsistent, wide dispersion up to 16 kHzTrue coaxial loudspeakers with HF compression driversTru-Phase™ high-frequency waveguidePatented Carbon Ring Cone Technology™Spring loaded Drop-Stop™ installation assistant tabs support the back can on the included rails and C-ring to simplify installationUniquely designed tile bridge support rails and snap-on C-ring support plates prevent sagTwist-Assist™ loudspeaker face retainer tabs for fast and easy installation3/4 and 1 knock-outs on the sides of the back canExternal loop-through Euroblock connectorsRear cover with integrated cable clamp (strain relief) and optional conduit knockoutSelectable 8 Ohm or 70V/100V operationBack can and face-only packages availableFive year warrantyCommunity D4 Specifications:Loudspeaker Type: Two-way, full-range, coaxial ceiling loudspeaker, 8 Ohm or 70V/100V operationOperating Range: 62 Hz - 18.5 kHzFrequency Response: 85 Hz - 16 kHz (+/- 5 dB)Max Input Ratings (8 Ohm): 60W continuous, 150W program; 22 volts RMS, 49 volts momentary peakTransformer Taps:70V: 30W, 15W, 7.5W, 3.75W and low impedance100V: 30W, 15W, 7.5WDistortion:500 Hz, 10% Full Power: 0.17% 2nd Harmonic, 0.86% 3rd Harmonic500 Hz, 1% Full Power: 0.09% 2nd Harmonic, 0.37% 3rd Harmonic2 kHz, 10% Full Power: 1.83% 2nd Harmonic, 0.81% 3rd Harmonic2 kHz, 1% Full Power: 0.55% 2nd Harmonic, 0.62% 3rd Harmonic8 kHz, 10% Full Power: 0.40% 2nd Harmonic, 0.07% 3rd Harmonic8 kHz, 1% Full Power: 0.21% 2nd Harmonic, 0.09% 3rd HarmonicSensitivity (1W/1m): 91 dB SPL (120 Hz to 12.5 kHz 1/3 octave bands); 92 dB SPL (250 Hz to 4 kHz speech range)Maximum Output: 109 dB SPL / 115 dB SPL (peak 8 Ohm)Nominal Impedance: 8 OhmsMinimum Impedance: 7.8 Ohms @ 260 HzNominal Coverage: 130º conical (1 kHz to 6 kHz); 140º conical (500 Hz to 6 kHz)Axial Q / DI: 4 / 6, 500 Hz to 6 kHzCrossover Frequency: 2 kHzRecommended Signal Processing: 62 Hz high pass filterDrivers: LF 1x 4.5, HF 1x 3/4 exit compression driverDriver Protection: Self-resetting solid state circuit breakerInput Connection: 4-position Euroblock connectorControls: Front-face wattage / low impedance selector switchEnclosure: Corrosion-resistant zinc plated steelMounting/Rigging Provisions: 3 steel mounting clamps with 3 grip rangeGrille: Powder coated steel with safety line, white finish, paintableBaffle: Reflex loaded UL 94V-0 rated ABSSafety Features: 3x safety hang pointsSafety Agency Ratings: ETL listed to comply with UL1480, UL2043 and CSA60065. Suitable for use in air handling spaces per NFPA 70 and NFPA 90.Face-Only / Back Can Options: D4-FO Face-Only Assembly, D45-BC Back CanRequired Accessories: Electronic high pass filterSupplied Accessories: C-Ring supporting plate, tile support bridge rails, grille, paint mask, cut-out template, flat screwdriverOptional Accessories:D45-FAR Face Adapter RingD45-CATR Can Adapter Ring / Trim RingD45-NCB New Construction BracketDimensions:Width: 9.768 (248.1 mm) bezel diameterDepth: 6.788 (172.4 mm) can depthCutout Diameter: 8.75 (222 mm)Weight: 7.6 lbs (3.4 kg)

CS6-W (= 2 Stück/ 2 Pieces) - Demoware vom deutschen Vertrieb- technisch neuwertig- leichte Gebrauchsspuren- incl. Originalverpackung- 2 Jahre Gewährleistung- Rechnung mit ausgew. MwSt The CS6 incorporates the same 6.5-inch full-range loudspeaker (as the C6) in a black or white paintable ABS surface mount enclosure. It also has a more focused dispersion than the smaller CS4. It contains a proprietary Tru-Phase™ waveguide that produces a consistently wide conical polar response up to 16 kHz. The CS6 features a genuine coaxial design using separate magnets for the LF and HF drivers for reduced distortion and high sensitivity, thereby permitting up to 3 dB greater output level while requiring up to half the amplification power of competing products.Easily outperforming loudspeakers of a larger size format, the CS6 provides high power handling, high sensitivity and realistic sound reproduction. This loudspeaker is equipped with a built-in autoformer, allowing large numbers of distributed loudspeakers to be powered from a 70V or 100V amplifier output. A convenient front-accessible power tap switch is hidden behind a rotatable logo. Installation is simple and flexible using the included multi-angle pan-tilt bracket which allows low profile mounting and precise positioning of the enclosure in either horizontal or vertical orientation.Thanks to the internally reinforced, black or white paintable ABS enclosures, zinc-rich epoxy dual-layer powder-coated grilles and brackets, weather-treated drivers, and the included IP56 sealed wiring cover, all standard surface mount models are equally suited for indoor or outdoor direct exposure applications.HIGHLIGHTSIncluded pan and tilt yokeCost effective design with uniform voicingOutdoor ready

Price is for 2 Pieces/ Preis gilt für ein Paar (= 2 Lautsprecher) The C6 has a more focused dispersion and a greater low frequency extension than the smaller C4. It contains a proprietary Tru-Phase waveguide that produces a consistently wide conical polar response up to 16 kHz. The C6 features a genuine coaxial design using separate magnets for the LF and HF drivers for reduced distortion and high sensitivity, thereby permitting up to 3 dB greater output level while requiring up to half the amplification power of competing products. The C SERIES ceiling loudspeakers are all ETL listed, and have similar sensitivity and output capabilities. HIGHLIGHTS High intelligibility with uniform coverage and voicing Easy installation Selectable 8 ohm or 70V/100V operation

SRH90 COMMUNITY RADIAL HORNS meilleurs horns fabriqués HIFI haut de gamme Les horns COMMUNITY sont faits en fibre de verre. Pas une fibre de verre bon marché pulvérisée, mais une fibre de verre stratifiée à la main par des experts et construite selon nos exigences exactes pour une précision acoustique maximale, une rigidité sans résonance et une solidité sans pareille. Nos horns sont absolument protèges au vieillissement. Ils ne rouilleront jamais et ne se corroderont jamais. Et il est peu probable quils se cassent, ni maintenant ni dans quarante ans. Trouvé sur Internet : « Ce nest pas une horne de diffraction - cest une SRH (Small Radial Horn) de Community Light & Sound. Peut-être un peu trop de dispersion horizontale dans ma pièce, mais si non, ce sont parmi les meilleurs horns fabriqués. Le son est spectaculaire. » Je pense jamais utilisés. Caractéristiques dans la dernière photo. Fabriqués aux USA dans les années ’70. VINTAGE les bons temps de la HIFI. C’est vous qui fixez les prix ! Payez ce que ça vaut !

Description Shipping Return Policy Local Pickup About Us Item Description Item Sku: W2-6-A-MayO28482 AS-IS, UNTESTED : Not tested in any shape or form. - Power cable/adapter: Not included, unless stated otherwise - May be missing internal parts we are not aware of, review all pictures in detail. - No warranty / No returns / No exchanges / No refunds. Shipping Policies When you purchase multiple items from us, were delighted to offer a 10% shipping discount on each additional item! We make it a priority to ship your order within 2-5 business days. If youre in a hurry, simply select our expedited service at checkout, and well make sure your order is shipped within just one business day. Were delighted to announce that were now offering palletizing options for larger orders. Send us an inquiry for a shipping quote to your area. We ship with FedEx, UPS, or Canada Post, depending on your location. Got a question about an item or shipping? Please feel free to send us a message directly. Were here to help! Return Policy We follow eBays return policies, so rest assured, weve got your back! Pick Up Item Locally We are located at the following address for your convenience: 1315 73 Ave SE, Calgary, AB T2H 2X1 Hours of operation: M-F 8:45-5:15pm. Local pickup is available for a small fee of $5.00 Canadian Dollars per order. Who we are at ERA The ERA is a non-profit organization dedicated to reducing electronic waste through the reuse and recycling of unwanted computers, laptops and related electronic equipment. We offer effective and easy solutions for electronics recycling in Toronto and cities across Canada and the U.S. Our team is committed to making a difference in local communities through a more sustainable approach to electronics disposal. At ERA, we believe there’s a better alternative to simply throwing away unwanted or unused electronic devices. For over 15 years, we’ve worked with local electronic recyclers in Canada and the U.S. to give your devices a new life by donating them to charities and organizations in need. We offer secure hard-drive data destruction and convenient pick-up and drop-off services, providing greater convenience and flexibility. Our team is dedicated to being a part of the change, helping both local communities and the environment thrive.

** WE DO NOT OFFER COMBINED SHIPPING. WHILE WE MAY PHYSICALLY COMBINE MULTIPLE ORDERS IN THE SAME SHIPMENT, WE DO NOT OFFER COMBINED SHIPPING COST REDUCTIONS. ** ** IF AN ITEM ARRIVES NOT AS DESCRIBED, WE HONOR A RETURN AND FULL REFUND WITH A COMPANY SUPPLIED SHIPPING LABEL. WE DO NOT OFFER EXCHANGES. ** ** WE SHIP IN 1-5 BUSINESS DAYS VIA STANDARD SERVICE. WE SHIP IN 1 BUSINESS DAY IF YOU SELECT EXPEDITED SERVICE. ** SKU: W2-6-A-MayO28482 AS-IS, UNTESTED : Not tested in any shape or form. - Power cable/adapter: Not included, unless stated otherwise - May be missing internal parts we are not aware of, review all pictures in detail. - No warranty / No returns / No exchanges / No refunds. Item will come as shown in the pictures Item condition : This correlates to the items condition under the product title. See our items condition and match it to one of the following : New: Item is new and will only come with what is shown in the pictures, Does not include original box or power adapter unless stated otherwise. Used: Item will come used, tested, and working. For parts: AS-IS: For parts only, No warranty / No returns. No guarantee for any form of functionality.Shows signs of normal use w/ some scuffs / scratches / blemishes / sticker residue.We do not have the ability to transfer licenses to applicable devices.No other accessories / hardware / software is included. Power cords/Adapters are not included unless permanently attached to device or stated in the ad. We do not provide software or software support. We ship in 1-5 business days.Returns are honored only for used/new items if there is a problem with the device. Items sold as-is / for parts / repair are not returnable. Please be advised CCW has limited staff available and doesnt have the capacity to entertain individual shipping requests.Theres also no more palletizing option available and we will not be storing items at our facility to be collected until theres enough for a pallet.All individual emails and complaints about combined shipping or palletizing will result in your account being blocked. When making offers: Please do not make any notes in comments otherwise our system will automatically decline the offers. We do not negotiate via the offer notes. Please do not request additional parts or discounts or special favours via the offer message as it will be automatically declined. If you have questions about items or shipping or otherwise, send us a message directly, not via the best offer message as it will be automatically declined. Packages are shipped via Fedex / UPS / Canada Post based on customer location. We are not setup for courier preferences. There is a local pickup fee of $5.00 Canadian Dollars per item. For International Freight shipping on large/Oversize items (50+lbs) Please contact us for a quote.

SRH90 COMMUNITY RADIAL HORNS meilleurs horns fabriqués HIFI haut de gamme Les horns COMMUNITY sont faits en fibre de verre. Pas une fibre de verre bon marché pulvérisée, mais une fibre de verre stratifiée à la main par des experts et construite selon nos exigences exactes pour une précision acoustique maximale, une rigidité sans résonance et une solidité sans pareille. Nos horns sont absolument protèges au vieillissement. Ils ne rouilleront jamais et ne se corroderont jamais. Et il est peu probable quils se cassent, ni maintenant ni dans quarante ans. Trouvé sur Internet : « Ce nest pas une horne de diffraction - cest une SRH (Small Radial Horn) de Community Light & Sound. Peut-être un peu trop de dispersion horizontale dans ma pièce, mais si non, ce sont parmi les meilleurs horns fabriqués. Le son est spectaculaire. » Je pense jamais utilisés. Caractéristiques dans la dernière photo. Fabriqués aux USA dans les années ’70. VINTAGE les bons temps de la HIFI. C’est vous qui fixez les prix ! Payez ce que ça vaut !

community Entasys loud speaker.