This is a top Mounted Replacement Tweeter that was removed from a B&W 702 s2 Floor speaker. When we removed it we had to cut the din connector off to pull through small access hole, but there is enough wire to rewire this connector back on and reuse. Part # HF01678 For the following models 702 S2705 S2

This is a listing for a fully functional 4Ohm tweeter with part number ZZ5460. The tweeter is in like new condition. This tweeter is used in a variety of speakers including DM600, DM610, DM620, etc. If you require more detailed information or close-up photographs, please do not hesitate to request them. The tweeter will be carefully packed to ensure secure transportation to any destination worldwide. Additionally, if you are in need of any other authentic used parts from B&W, feel free to inquire as we may be able to acquire them for you.

I am a B&W, Bowers & Wilkins Hi-Fi Audio Consultant for over 40-years. This Tweeter Diaphragm was accidently Pushed I,, then professionally pushed back.What you see in the photos is what you will receive. It is 100% in working order. No Issues.Has a slight wrinkle impression on the dome, does not effect sound. Bowers & Wilkins NAUTILUS Tweeter ZZ22943 for:B&W CM1 Bookshelf SpeakersB&W CM7 Tower SpeakersB&W CM8 Tower SpeakersB&W CDS3 Wall SpeakersB&W DS3 Wall Speakers Shipping & Handling, and Conditions: * Ships only to the 48-states. * No International Sales. * Pay with PayPal Only, must have a Confirmed/ Verified shipping address with PayPal. * Cost of Shipping: $10 ( to the 48-states). * All sales are final, No Refunds.

( See Additional Pictures, Below this eBay Listing ) am a B&W, Bowers & Wilkins Hi-Fi Audio Consultant for over 40-years. What you see in the pictures is what you will receive. What you will receive:Bowers & Wilkins NAUTILUS, HF Motor System, Tweeter Diaphragm with 1 Alum Dome.For B&W Speakers: CM1, CM7, CM8, DS3, CDS3 Your Box will be Labeled: ZZ22943, but is compatible with all of the speakers below: ( manufactured by B&W: Tues, 22nd/ Nov/ 2022 ) B&W Speakers Original Part #: B&W CM1 ZZ22943B&W CM7 ZZ22943B&W CM8 ZZ22943B&W DS3 ZZ22943B&W CDS3 ZZ22943 Shipping & Handling, and Conditions: * Ships only to the 48-states. * No International Sales. * Pay with PayPal Only, must have a Confirmed/ Verified shipping address with PayPal. * Cost of Shipping: 10.00 ( to the 48-states). * All sales are final, No Refunds. Exclude shipping locationsExclude specific locations (regions, countries, PO boxes) that you dont want to ship to. To save time and list faster, go to My eBay Site Preferences and select the specific locations you want to exclude on allyour listings. Learn moreExcluded locations:Alaska/Hawaii, US Protectorates, APO/FPO, Africa, Asia, Central America and Caribbean, Europe, Middle East, Oceania, Southeast Asia, South America, PO Box

This is a listing for a fully functional 4Ohm tweeter with part number ZZ5460. The tweeter is in like new condition. This tweeter is used in a variety of speakers including DM600, DM610, DM620, etc. If you require more detailed information or close-up photographs, please do not hesitate to request them. The tweeter will be carefully packed to ensure secure transportation to any destination worldwide. Additionally, if you are in need of any other authentic used parts from B&W, feel free to inquire as we may be able to acquire them for you.

2 x Bowers Wilkins B&W CM 1 Generic Replacement Tweeter Loudspeakers Coils Foils.Always fit in pairs, that way they will look exactly the same & they will also sound exactly the same.You are buying a pair of generic replacement tweeter coils & foils (as seen on these pictures) to fit the Bowers Wilkins CM-1, CM-3, CM-5, CM-7, CM-9 loudspeakers.They are a very good replacement for your old blown or dented tweeters.Dependant on when exactly your tweeters were made, you may have to extend the fine joining wires (just solder then where they end) instead of on the connecting posts.Again dependant on when exactly your tweeters were made, these will either slot straight into place or you will find they are about 1.5mm wider that the slot for them.If they are slightly wider, then all you need to do is to put a very thin edge of superglue around the edge of your plastic tweeter surround (use the tip of a cotton bud) & then place the tweeter coil - foil in place using the magnet part of your complete unit to line it up while the glue sets.BEFORE you first open the tweeter up make sure that you mark the position of both parts of the tweeter, they slot together in a certain place & marking them before opening them will save you loads of time & agro later on.You will need the following tools to fit these.A philips screwdriver (small - medium head)A flathead screwdriver (small - medium head)A soldering iron & solder.Some superglug & a cotton bud.These replacement tweeter coils & foils can be used with many bowers & wilkins loudspeakers.You will need a steady hand, a fair degree of common sence (like do not glue into place until you have made sure it fits together correctly) & a few minutes spare time when fitting these.REMEMBER, THEY ARE VERY DELICATE, NO RETURNS ON ANY COILS - FOILS THAT YOU DAMAGE WHILST FITTING THEM.RETURNS ON BRAND NEW NOT FITTED COILS - FOILS ONLY.If you are not still not sure about fitting these, in the first instance have a look on youtube, you will be able to find videos on there showing what to do.If you still have issues, then send an email through ebay messaging to us, we will attempt to get back to you within 24hrs (we are NOT sat on the computer 24/7)FREE UK SHIPPING ON THIS ITEM.All items are sent by signed for & recorded delivery.