M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. A hi-res Surround Bass Management system for audiophiles and film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system. No PSU.

M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. A hi-res Surround Bass Management system for audiophiles and film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system. No PSU.

M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. A hi-res Surround Bass Management system for audiophiles and film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system. No PSU.

M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. (See Photos.) No PSU. Surround bass management for audiophiles or film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system.

M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. (See Photos.) No PSU. Surround bass management for audiophiles or film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system.

M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. (See Photos.) No PSU. Surround bass management for audiophiles or film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system.

M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. (See Photos.) No PSU. Surround bass management for audiophiles or film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system.

M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. (See Photos.) No PSU. Surround bass management for audiophiles or film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system.

M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. (See Photos.) No PSU. Surround bass management for audiophiles or film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system.

M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. (See Photos.) No PSU. Surround bass management for audiophiles or film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system.

M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. (See Photos.) No PSU. Surround bass management for audiophiles or film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system.

M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. (See Photos.) No PSU. Surround bass management for audiophiles or film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system.

M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. (See Photos.) No PSU. Surround bass management for audiophiles or film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system.

M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. (See Photos.) No PSU. Surround bass management for audiophiles or film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system.

M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. (See Photos.) No PSU. Surround bass management for audiophiles or film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system.

M&K BMC-1 Miller & Kreisel Sound Bass Management Controller in Near Mint condition. (See Photos.) No PSU. Surround bass management for audiophiles or film editors. The M&K Sound BMC-1 is a balanced, line-level studio bass management controller intended for use with M&K Sounds line of professional studio monitors and with high-end home theater installations. Although the BMC-1 was primarily designed for monitoring 5.1 audio, its flexible architecture allows it to be used for monitoring mono, stereo, Dolby Surround, Dolby Digital, DTS and other formats. The BMC-1 combines several necessary functions in one 19” rack mount 1RU package. Along with bass management and LFE channel control, it also provides individual channel adjustment capability to properly calibrate your entire monitor system. The controller consists of a series of five high-pass filters (one each for the L, C, R, LS, RS channels) that route high frequency information (above 80Hz) to their appropriate channels amplifier and speaker. Each channel is also routed through a matching 80Hz lowpass filter. This low frequency information is then routed to a summing amplifier, which in turn sends this low frequency information, along with the LFE channel, to two subwoofer outputs. This is done for two reasons. First, small loudspeakers may not be able to properly reproduce information below 80Hz. This information is therefore summed together and redirected from the individual channels to a loudspeaker that can reproduce this low frequency information with clarity and power “ a subwoofer. With the introduction of digital audio, it has become necessary for loudspeaker systems to be able to accurately reproduce audio that has a bandwidth of 20Hz to 20kHz with wide dynamics. A satellite/subwoofer system is the best way to accomplish this. Secondly, todays home theater receivers utilize bass management per Dolby requirements. In order for work done in the studio to translate properly, the mixer must hear his mix exactly the way it will ultimately be played back. The BMC-1 together with a properly set-up and calibrated M&K Sound monitor system allows the mixer to hear his work with more accuracy than might otherwise be possible. Front Panel Trim Controls +/- 12dB trim control for balancing the system.

100% Authentic! All packages are shipped directly from Japan!Condition DescriptionFeatures and Remarks Equipped with belt drive type CD drive. Top loading system with stabilizer. Features & Remarks Equipped with BMCs original SUPERLINK, featuring CI current drive technology and LEF output. Features / Remarks Will be shipped in the original box wrapped in cushioning material. Accessories Box, instruction manual, power cable, remote control, connection cable Please Note shipping from Japan. Policy PaymentYou can use various payment methods based on eBay Managed Payments. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.Cancellations & ReturnsCancellation or returns will be accepted only if the item has an obvious problem that was not mentioned in the listing description. If that, please let us know within 3 days you got the item. Buyer is responsible for shipping costs and any charge incurred shipping products back.International BuyersImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges.

100% Authentic! All packages are shipped directly from Japan!Condition DescriptionFeatures and Remarks Equipped with belt drive type CD drive. Top loading system with stabilizer. Features & Remarks Equipped with BMCs original SUPERLINK, featuring CI current drive technology and LEF output. Features / Remarks Will be shipped in the original box wrapped in cushioning material. Accessories Box, instruction manual, power cable, remote control, connection cable Please Note shipping from Japan. Policy PaymentYou can use various payment methods based on eBay Managed Payments. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.Cancellations & ReturnsCancellation or returns will be accepted only if the item has an obvious problem that was not mentioned in the listing description. If that, please let us know within 3 days you got the item. Buyer is responsible for shipping costs and any charge incurred shipping products back.International BuyersImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges.

Lenco BMC-180BK Karaoke Mikrofon mit Bluetooth - Schwarz. Zustand wie neu Einmal gebraucht

100% Authentic! All packages are shipped directly from Japan!Condition DescriptionFeatures and Remarks Equipped with belt drive type CD drive. Top loading system with stabilizer. Features & Remarks Equipped with BMCs original SUPERLINK, featuring CI current drive technology and LEF output. Features / Remarks Will be shipped in the original box wrapped in cushioning material. Accessories Box, instruction manual, power cable, remote control, connection cable Please Note shipping from Japan. Policy PaymentYou can use various payment methods based on eBay Managed Payments. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.Cancellations & ReturnsCancellation or returns will be accepted only if the item has an obvious problem that was not mentioned in the listing description. If that, please let us know within 3 days you got the item. Buyer is responsible for shipping costs and any charge incurred shipping products back.International BuyersImport duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges.