Bang & Olufsen B&o Beolab 4500 Aktiv Lautsprecher Mondrian Top Condition DealerThe description of this item has been automatically translated. If you have any questions, please feel free to contact us. Bang & Olufsen Beolab 4500 active wall speakersFor sale here are a pair of fantastically beautiful active Bang & Olufsen Beolab 4500 wall speakers ( Mondrian ) including two wall brackets and two Powerlink cables, so everything is complete.Technically, the masterpieces work 100% flawlessly and optically both speakers are in very good general condition.I would highly recommend picking it up personally with a functional test at my place. Shipping takes place in a very stable Styrofoam box + another outer carton, so that the item will be 100% perfectly packed and will also be delivered to you 100% undamaged! Shipping costs abroad (Europe + worldwide) I have indicated, should the shipping costs for your country not be visible on Ebay, then please write to me.For buyers from countries with a power supply of 110 volts, a voltage converter is then required (not included in the offer), because the item has a power supply of 220-240 volts.For information, when shipping to a non-EU country, the buyer will have to pay additional customs fees when the package is delivered, please note this.Scope of delivery:° 1 pair of Bang & Olufsen Beolab 4500 active wall speakers (Mondrian)° 2 wall brackets° 2 Powerlink cablesIn my other auctions I also offer more very nice Bang & Olufsen devices for sale!As far as the warranty is concerned, I ask you to read this in my Ebay dealer terms and conditions!!! We are also happy to take your old B&O system or your B&O loudspeakers in part exchange, even if they are defective!I would highly recommend picking it up personally with a functional test at my place. Shipping takes place in a very stable Styrofoam box + another outer carton, so that the item will be 100% perfectly packed and will also be delivered to you 100% undamaged! Shipping costs abroad (Europe + worldwide) I have indicated, should the shipping costs for your country not be visible on Ebay, then please write to me. For buyers from countries with a power supply of 110 volts, a voltage converter is then required (not included in the offer), because the item has a power supply of 220-240 volts. For information, when shipping to a non-EU country, the buyer will have to pay additional customs fees when the package is delivered, please note this. !! We are also happy to take your old B&O system or you Marke Bang & Olufsen Angebotspaket Nein Form Wandlautsprecher EAN nichtzutreffend Farbe Mehrfarbig Besonderheiten Inklusive zwei Wandhalterungen Besonderheiten Inklusive 2 Powerlinkkabel Modell Beolab 4500 Aktiv Lautsprecher Herstellernummer nicht zutreffend Konnektivität Verkabelt Audioeingänge 1 x Line Eingang pro Box ( für externe Geräte ) Audioeingänge 2 x Powerlinkanschlüsse pro Box Audioeingänge 1 x Speaker Link pro Box Herstellungsland und -region Dänemark Herstellergarantie keine Produktart Aktiv Lautsprecher Paar

Bang & Olufsen Beolab 4500 Aktiv Wandlautsprecher Zum verkauf kommen hier ein paar traumhaft schöne Aktive Bang & Olufsen Beolab 4500 Wandlautsprecher ( Mondrian ) inklusive zwei Wandhalterungen und zwei Powerlinkkabel, also alles komplett. Technisch funktionieren die Meisterstücke voll zu 100% einwandfrei und optisch sind beide Lautsprecher in einem sehr guten Allgemeinzustand. Eine persönliche Abholung mit einem Funktionstest bei mir vor Ort würde ich sehr empfehlen. Ein Versand erfolgt in einer sehr stabilen Styropor Kiste + noch ein Umkarton, so dass der Artikel zu 100% perfekt verpackt sein wird und auch zu 100% unbeschädigt bei Ihnen zugestellt wird !! Versandkosten ins Ausland ( Europa + Weltweit ) habe ich angegeben, sollten die Versandkosten für Ihr Land bei Ebay nicht zu ersehen sein, dann bitte ich Sie mich anzuschreiben. Für Käufer aus den Ländern mit einer Stromversorgung von 110 Volt wird dann noch ein Spannungswandler benötigt ( nicht im Angebot enthalten ), denn der Artikel hat eine Stromnetzversorgung von 220-240 Volt. Zur Info, bei einem Versand in ein nicht EU Land fallen für den Käufer bei Zustellung des Paketes noch zusätzliche Zollgebühren an, bitte dies beachten. Lieferumfang: ° 1 paar Bang & Olufsen Beolab 4500 Aktiv Wandlautsprecher ( Mondrian ) ° 2 Wandhalterungen° 2 Powerlinkkabel In meinen weiteren Auktionen biete ich auch noch mehr sehr schöne Bang & Olufsen Geräte zum kauf an !! Was die Gewährleistung betrifft, erbitte ich Sie diese in meiner Ebay Händler AGB nachzulesen !! !! Gerne nehmen wir auch Ihre alte B&O Anlage oder Ihre B&O Lautsprecher in Zahlung, auch Defekt !!

This is a pair of B&O Beloab 4500 speakers. They are meant to be wall mounted and STB brackets are included. These are rated at 116 watts each. If connected to B&O equipment that used MKIII cables, will display source and volume. Otherwise work quite well with newer B&O and non-B&O equipment. With older B&O equipment with amplifier built in, you can bypass the built-in amplifier entirely with an older 2 or 4 -pin B&O DIN cable. These really are quite versatile. The grills are in great shape and the plastic and aluminum parts only show light wear. Surrounds are flexible and show no deterioration. The grills are easily removed and can be recovered in the fabric of your choice to match your decor. Based on last sale price, inflation and conversion rate, these would go for about $2800 USD today. Here is some info from our friends at Beoworld: BeoLab 4500 was a wall speaker which was no more than 8cm deep. It had a built-in (active) amplifier and extended bass reproduction, which used the wall as a reflector. The display told you which source that BeoLab 4500 was reproducing at any one time. There were two versions of this panel loudspeaker. The pure Beovox 4500 loudspeaker (shown here) and BeoLab 4500 with built-in amplifier and Dynamic Bass Equaliser (shown in main picture above), which automatically compensated for the inability of the human ear to perceive deep bass tones at low volume The design of BeoLab 4500 and Beovox 4500 was based an acoustic principle that allowed the loudspeaker to use the wall to enhance the bass level. The cabinet let the sound waves reflect off the wall and out into the room without delay. This made it possible to reduce the depth of the cabinet to just 8cm, so the loudspeaker becomes a natural part of the wall décor. BeoLab 4500 had a display which indicated sound source, volume and which track on CD or tape that you were listening to. In looks, it was similar to the BeoLab 5000 active speaker, but smaller. The display too was in a green-coloured LED as opposed to BeoLab 5000s orange. Both loudspeakers were available with blue or grey fabric.The speakers are approximately 18 x 21 and weigh about 20 pounds each. I will probably ship in two boxes for safety. A single 40+ pound box just is an invitation to be dropped. A couple things to be aware of. These currently have a power cable (5-6 foot) attached to them with a squeeze lock connector. See last photos. I am also including two 12-foot power cables (last photo) should you wish to wall mount these and hide the power cables in the wall. As such, the existing power connection should be considered temporary only. It works and they are well protected, but you should decide where to mount, run power cables and permanently affix them. Note that these use polarized cables. I have marked the connectors and the cords so you will know which is the black (hot) wire. I forgot to take a picture, but I hid the cable behind a metal plate that you can just see a bit of in the next to last photo.. This helps make them more secure. There is a switch on the side of each speaker that acts as a source and power switch. It needs to be in the right position. Also, B&O equipment can be sensitive to receiving input before turning on. You should connect these to your equipment, make sure the speaker selector is in the right position and then turn on the audio source. On Apr-25-23 at 07:18:50 PDT, seller added the following information: I stand corrected.  Upon further research, the MKIII cables will not work to enable the display.  These are the thinner 2.5mm cables and do not pass thru the data line.  The correct cable is the MKII, which has Pin 6 for data, Pin 1 for auto on/off and pin 8 for overload protection.  This is the thicker 3.5mm cable and does not have the triangle on the plug hood (B&O OEM cables). Use of the improper cable may cause the speaker to not auto turn on/off or display the source and volume data. Sorry for any confusion.  :-{On Apr-25-23 at 18:06:25 PDT, seller added the following information: I was asked about the displays.  I had taken one picture of one working, but not both as they were wrapped. I partially unwrapped the other speaker and hooked it to an amplifier so you can see the display also works.  It is the last photo.  Thank you.

This is a pair of B&O Beloab 4500 speakers. They are meant to be wall mounted and STB brackets are included. These are rated at 116 watts each. If connected to B&O equipment that used MKIII cables, will display source and volume. Otherwise work quite well with newer B&O and non-B&O equipment. With older B&O equipment with amplifier built in, you can bypass the built-in amplifier entirely with an older 2 or 4 -pin B&O DIN cable. These really are quite versatile. The grills are in great shape and the plastic and aluminum parts only show light wear. Surrounds are flexible and show no deterioration. The grills are easily removed and can be recovered in the fabric of your choice to match your decor. Based on last sale price, inflation and conversion rate, these would go for about $2800 USD today. Here is some info from our friends at Beoworld: BeoLab 4500 was a wall speaker which was no more than 8cm deep. It had a built-in (active) amplifier and extended bass reproduction, which used the wall as a reflector. The display told you which source that BeoLab 4500 was reproducing at any one time. There were two versions of this panel loudspeaker. The pure Beovox 4500 loudspeaker (shown here) and BeoLab 4500 with built-in amplifier and Dynamic Bass Equaliser (shown in main picture above), which automatically compensated for the inability of the human ear to perceive deep bass tones at low volume The design of BeoLab 4500 and Beovox 4500 was based an acoustic principle that allowed the loudspeaker to use the wall to enhance the bass level. The cabinet let the sound waves reflect off the wall and out into the room without delay. This made it possible to reduce the depth of the cabinet to just 8cm, so the loudspeaker becomes a natural part of the wall décor. BeoLab 4500 had a display which indicated sound source, volume and which track on CD or tape that you were listening to. In looks, it was similar to the BeoLab 5000 active speaker, but smaller. The display too was in a green-coloured LED as opposed to BeoLab 5000s orange. Both loudspeakers were available with blue or grey fabric.The speakers are approximately 18 x 21 and weigh about 20 pounds each. I will probably ship in two boxes for safety. A single 40+ pound box just is an invitation to be dropped. A couple things to be aware of. These currently have a power cable (5-6 foot) attached to them with a squeeze lock connector. See last photos. I am also including two 12-foot power cables (last photo) should you wish to wall mount these and hide the power cables in the wall. As such, the existing power connection should be considered temporary only. It works and they are well protected, but you should decide where to mount, run power cables and permanently affix them. Note that these use polarized cables. I have marked the connectors and the cords so you will know which is the black (hot) wire. I forgot to take a picture, but I hid the cable behind a metal plate that you can just see a bit of in the next to last photo.. This helps make them more secure. There is a switch on the side of each speaker that acts as a source and power switch. It needs to be in the right position. Also, B&O equipment can be sensitive to receiving input before turning on. You should connect these to your equipment, make sure the speaker selector is in the right position and then turn on the audio source. On Apr-25-23 at 07:18:50 PDT, seller added the following information: I stand corrected.  Upon further research, the MKIII cables will not work to enable the display.  These are the thinner 2.5mm cables and do not pass thru the data line.  The correct cable is the MKII, which has Pin 6 for data, Pin 1 for auto on/off and pin 8 for overload protection.  This is the thicker 3.5mm cable and does not have the triangle on the plug hood (B&O OEM cables). Use of the improper cable may cause the speaker to not auto turn on/off or display the source and volume data. Sorry for any confusion.  :-{On Apr-25-23 at 18:06:25 PDT, seller added the following information: I was asked about the displays.  I had taken one picture of one working, but not both as they were wrapped. I partially unwrapped the other speaker and hooked it to an amplifier so you can see the display also works.  It is the last photo.  Thank you.