Bang & Olufsen Beogram RX . B&O High Fidelity Plattenspieler. Turntable. Record. Vollautomatischer Plattenspieler funktioniert ohne Maken, wie es soll. Sie können zum Hrprobe vorbei kommen oder ich sende eine Video auf Ihre Wnsch. Verkauft wird mit original mmc2 Tonabnehmer aber mit nachgebaute Nadel. Die Nadel ist NEU und nur eine Platte zum Probe bespielt hat. Alleine mmc2 Tonabnehmer kostet heutzutage ab 250 bis 500 . Der Plattenspieler befindet sich in einem sauberen Super-Zustand. Keine kratzer. Passende Tonabnehmer: mmc1, mmc2, mmc3, mmc4, mmc5. Da ist Privatverkauf. Dacher keine Garantie, keine Rcknahme.Video Selbstabholung in Dsseldorf bevorzugt. Zahlungart: Paypal-Freunde oder Überweisung. Bei PayPal-Standart Zahlung die Gebühren überniemt der Kufer.

Beogram RX2 Hebeautomatik defekt. Plattenspieler etwa von 1986. Durch eine Fachwerkstatt habe ich mitgeteilt bekommen, dass die Hebeautomatik kaputt ist. Damals hätte die Reparatur 300 € gekostet. Das war mir zu viel. Seither steht er rum und ich habe mich nun zur Abgabe entschieden. Funktion : Alles normal, aber der Tonarm rutscht nach dem ersten Lied über die Platte. Nicht enthalten: Die Tonabnehmer können einzeln gegen Gebot erworben werden. Zusätzlich ist ein weiterer Tonabnehmer vorhanden, den ich seinerzeit als Ersatz gekauft habe, weil ich noch nicht wusste woran es liegt. Dieser hat eine verbogene Nadel, funktioniert aber einwandfrei. Kann extra oder im Paket gekauft werden. 30€ extraAm 09.06.23 hat der Verkäufer die folgenden Angaben hinzugefügt: Beogram RX2 Hebeautomatik defekt. Plattenspieler etwa von 1986. Durch eine Fachwerkstatt habe ich mitgeteilt bekommen, dass die Hebeautomatik kaputt ist. Damals hätte die Reparatur 300 € gekostet. Das war mir zu viel. Seither steht er rum und ich habe mich nun zur Abgabe entschieden. Funktion : Alles normal, aber der Tonarm rutscht nach dem ersten Lied über die Platte. Nicht enthalten: Die Tonabnehmer Der zweite Tonabnehmer mit der verbogenen Nadel ist verkauft)

Original Bang & Olufsen MMC4 Cartridge/StylusUk stock ready for dispatch NOW Sounds greatChecked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1.2gram vertical tracking force MMC4 Specifications Description Titanium-bonded elliptical diamond, mounted on a tapered aluminium cantilever Tracking force - grams 1.2 Diamond Stylus Elliptical Cantilever tube. Tap. alum. . Effective tip mass mg 0,4 Compliance mg/mN 25 Frequency 20-20000 Hz=/-dB 2,5 Channel separation 1000>dB 22 Output mV/cm/s RMS 0,6 Cartridge weight gram 1,6 Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridge If you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Original Bang & Olufsen MMC4 Cartridge/StylusUk StockSounds greatChecked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1.2gram vertical tracking force MMC4 Specifications Description Titanium-bonded elliptical diamond, mounted on a tapered aluminium cantilever Tracking force - grams 1.2 Diamond Stylus Elliptical Cantilever tube. Tap. alum. . Effective tip mass mg 0,4 Compliance mg/mN 25 Frequency 20-20000 Hz=/-dB 2,5 Channel separation 1000>dB 22 Output mV/cm/s RMS 0,6 Cartridge weight gram 1,6 Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridge If you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Original Bang & Olufsen MMC2 Cartridge/StylusNewly refurbished Bang & Olufsen MMC2.Refurbished suspension with an original Bang & Olufsen nude multi-radial contact line diamond mounted on a sapphire tube cantilever.Tracking perfectly with 1gram vertical tracking forceMMC2 Specifications :Nude multi-radial Contact Line diamond mounted on a sapphire cantileverTracking force 1 gramNude Contact Line diamond stylusCantilever tube - sapphire Effective tip mass 0.3 mgCompliance mg/mN 30Frequency 20-20000 Hz=/-dB 1.5Channel separation 1000>dB 25Output mV/cm/s RMS 0.6Cartridge weight 1.6 grams Courtesy of Beoworld.orgMMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis.The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker.A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play.While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear.Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies. Any questions just get in touch, Id be glad to help.

Original Bang & Olufsen MMC5 Cartridge/StylusUk stock ready for dispatch NOW Sounds greatChecked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1.5gram vertical tracking force Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridge If you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Original Bang & Olufsen MMC5 Cartridge/StylusUk stock ready for dispatch NOW Sounds greatChecked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1.5gram vertical tracking force Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridge If you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Beogram RX2 Hebeautomatik defekt. Plattenspieler etwa von 1986. Durch eine Fachwerkstatt habe ich mitgeteilt bekommen, dass die Hebeautomatik kaputt ist. Damals hätte die Reparatur 300 € gekostet. Das war mir zu viel. Seither steht er rum und ich habe mich nun zur Abgabe entschieden. Funktion : Alles normal, aber der Tonarm rutscht nach dem ersten Lied über die Platte. Nicht enthalten: Die Tonabnehmer können einzeln gegen Gebot erworben werden. Zusätzlich ist ein weiterer Tonabnehmer vorhanden, den ich seinerzeit als Ersatz gekauft habe, weil ich noch nicht wusste woran es liegt. Dieser hat eine verbogene Nadel, funktioniert aber einwandfrei. Kann extra oder im Paket gekauft werden. 30€ extraAm 09.06.23 hat der Verkäufer die folgenden Angaben hinzugefügt: Beogram RX2 Hebeautomatik defekt. Plattenspieler etwa von 1986. Durch eine Fachwerkstatt habe ich mitgeteilt bekommen, dass die Hebeautomatik kaputt ist. Damals hätte die Reparatur 300 € gekostet. Das war mir zu viel. Seither steht er rum und ich habe mich nun zur Abgabe entschieden. Funktion : Alles normal, aber der Tonarm rutscht nach dem ersten Lied über die Platte. Nicht enthalten: Die Tonabnehmer Der zweite Tonabnehmer mit der verbogenen Nadel ist verkauft)

Bang & Olufsen Beogram RX . B&O High Fidelity Plattenspieler. Turntable. Record. Vollautomatischer Plattenspieler funktioniert ohne Maken, wie es soll. Sie können zum Hrprobe vorbei kommen oder ich sende eine Video auf Ihre Wnsch. Verkauft wird mit original mmc2 Tonabnehmer aber mit nachgebaute Nadel. Die Nadel ist NEU und nur eine Platte zum Probe bespielt hat. Alleine mmc2 Tonabnehmer kostet heutzutage ab 250 bis 500 . Der Plattenspieler befindet sich in einem sauberen Super-Zustand. Keine kratzer. Passende Tonabnehmer: mmc1, mmc2, mmc3, mmc4, mmc5. Da ist Privatverkauf. Dacher keine Garantie, keine Rcknahme.Video Selbstabholung in Dsseldorf bevorzugt. Zahlungart: Paypal-Freunde oder Überweisung. Bei PayPal-Standart Zahlung die Gebühren überniemt der Kufer.

Bang & Olufsen B&O Beogram RX 2 turntable MMC 5 Cartridge no a stylus For Parts!!! Turntable turns but cannot be tested without a stylus. SOLD AS IS FOR PARTS!

I know next to nothing about record players I know enough to know that Bang & Olufsen makes very nice stereo equipment.The player Powers On, Spins, The arm moves over to the album and drops down then sometimes it will move along the record and others it will not both channels work but they sound that comes out is not great. On the little research I did I think it has to do with the tracking or the needle on the cassette. I looked and the needle looks sharp but once again I am not an expert. This could be a very simple fix for all I know but I am selling it for parts due to not being able to make it work properly in the time I had to spend on it.If it is a simple fix I hope you either use it or sell it and get enjoyment from it one way or the other. It is in great physical condition the only flaw being the circle that is melted in the dust cover (See Picture). IT IS BEING SOLD AS-IS FOR PARTS OR REPAIR I WILL NOT ACCEPT RETURNS ON THIS ITEM.

Bang & Olufsen B&O Beogram RX 2 turntable MMC 5 Cartridge no a stylus For Parts!!! Turntable turns but cannot be tested without a stylus. SOLD AS IS FOR PARTS!

Original Bang & Olufsen MMC5 Cartridge/StylusUk stock ready for dispatch NOW Sounds greatChecked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1.5gram vertical tracking force Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridge If you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Original Bang & Olufsen MMC4 Cartridge/StylusUk stock ready for dispatch NOW Sounds greatChecked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1.2gram vertical tracking force MMC4 Specifications Description Titanium-bonded elliptical diamond, mounted on a tapered aluminium cantilever Tracking force - grams 1.2 Diamond Stylus Elliptical Cantilever tube. Tap. alum. . Effective tip mass mg 0,4 Compliance mg/mN 25 Frequency 20-20000 Hz=/-dB 2,5 Channel separation 1000>dB 22 Output mV/cm/s RMS 0,6 Cartridge weight gram 1,6 Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridge If you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Bang & Olufsen Beogram RX2 Type 5831. Bought this deck brand new in the mid 80s , spent a lot of its life in the loft so in pretty good condition All works fine have vid of it working can send if your interested call 07710073414 if no answer please text and ill get back to you Can post but far better if you can collect

Bang & Olufsen Beogram RX2 Type 5833 Turntable record player. Doesn't power on. 120v 60 hz 10watts This turntable would be a great restoration project because both the cabinet and plexiglass cover are in excellent shape. There are no chips, dings, stains or big scratches. Just some superficial swirling on the plexi which is hardly noticeable. Yes there are less expensive ones but we think this is cosmetically one of the best used ones. We do not have the OG box but will bubble pack it and isolate the tonearm so it doesn't move. Just the turntable for sale and no cartridge.

Up for grabs is this very nice, lightly used Bang & Olufsen turntable. It displays extremely nice having a freshly polished clear dust cover lens. It looks remarkably nice in person. All functions such as the auto start and stop work perfectly every time and the platter maintains a good constant speed. Installed/included is a MMC5 cartridge which sounds very nice. I included a video demo of the auto start/stop. Still has the original manual brochure! Please see all pictures and ask any questions! This will be packed VERY well having the platter wrapped separately inside the box with the turntable and having everything bubble wrapped and surrounded by packing peanuts. As with most units I sell I guarantee this to work properly for 60 days from the delivery date and back that up with eBays 60 day free return policy. I take pride in my 100% positive feedback rating and always do my best to insure all my customers are happy!

Bang & Olufsen Beogram RX . B&O High Fidelity Plattenspieler. Turntable. Record. Vollautomatischer Plattenspieler funktioniert ohne Maken, wie es soll. Sie können zum Hrprobe vorbei kommen oder ich sende eine Video auf Ihre Wnsch. Verkauft wird mit original mmc2 Tonabnehmer aber mit nachgebaute Nadel. Die Nadel ist NEU und nur eine Platte zum Probe bespielt hat. Alleine mmc2 Tonabnehmer kostet heutzutage ab 250 bis 500 . Der Plattenspieler befindet sich in einem sauberen Super-Zustand. Keine kratzer. Passende Tonabnehmer: mmc1, mmc2, mmc3, mmc4, mmc5. Da ist Privatverkauf. Dacher keine Garantie, keine Rcknahme.Video Selbstabholung in Dsseldorf bevorzugt. Zahlungart: Paypal-Freunde oder Überweisung. Bei PayPal-Standart Zahlung die Gebühren überniemt der Kufer.

Bang & Olufsen B&O Beogram RX 2 turntable MMC 5 Cartridge no a stylus For Parts!!! Turntable turns but cannot be tested without a stylus. SOLD AS IS FOR PARTS!

Tested and works great! Has the more desirable mmc-5 cartridge. There are no major blemishes on the unit, some light scratches to be expected as this is a vintage unit. The cover/lid is free of chips, cracks, broken hinges etc. A really nice unit overall.

Beogram RX2 Hebeautomatik defekt. Plattenspieler etwa von 1986. Durch eine Fachwerkstatt habe ich mitgeteilt bekommen, dass die Hebeautomatik kaputt ist. Damals hätte die Reparatur 300 € gekostet. Das war mir zu viel. Seither steht er rum und ich habe mich nun zur Abgabe entschieden. Funktion : Alles normal, aber der Tonarm rutscht nach dem ersten Lied über die Platte. Nicht enthalten: Die Tonabnehmer können einzeln gegen Gebot erworben werden. Zusätzlich ist ein weiterer Tonabnehmer vorhanden, den ich seinerzeit als Ersatz gekauft habe, weil ich noch nicht wusste woran es liegt. Dieser hat eine verbogene Nadel, funktioniert aber einwandfrei. Kann extra oder im Paket gekauft werden. 30€ extraAm 09.06.23 hat der Verkäufer die folgenden Angaben hinzugefügt: Beogram RX2 Hebeautomatik defekt. Plattenspieler etwa von 1986. Durch eine Fachwerkstatt habe ich mitgeteilt bekommen, dass die Hebeautomatik kaputt ist. Damals hätte die Reparatur 300 € gekostet. Das war mir zu viel. Seither steht er rum und ich habe mich nun zur Abgabe entschieden. Funktion : Alles normal, aber der Tonarm rutscht nach dem ersten Lied über die Platte. Nicht enthalten: Die Tonabnehmer Der zweite Tonabnehmer mit der verbogenen Nadel ist verkauft)

Beogram RX2 Hebeautomatik defekt. Plattenspieler etwa von 1986. Durch eine Fachwerkstatt habe ich mitgeteilt bekommen, dass die Hebeautomatik kaputt ist. Damals hätte die Reparatur 300 € gekostet. Das war mir zu viel. Seither steht er rum und ich habe mich nun zur Abgabe entschieden. Funktion : Alles normal, aber der Tonarm rutscht nach dem ersten Lied über die Platte. Nicht enthalten: Die Tonabnehmer können einzeln gegen Gebot erworben werden. Zusätzlich ist ein weiterer Tonabnehmer vorhanden, den ich seinerzeit als Ersatz gekauft habe, weil ich noch nicht wusste woran es liegt. Dieser hat eine verbogene Nadel, funktioniert aber einwandfrei. Kann extra oder im Paket gekauft werden. 30€ extra

Bang & Olufsen Beogram RX . B&O High Fidelity Plattenspieler. Turntable. Record. Vollautomatischer Plattenspieler funktioniert ohne Maken, wie es soll. Sie können zum Hrprobe vorbei kommen oder ich sende eine Video auf Ihre Wnsch. Verkauft wird mit original mmc2 Tonabnehmer aber mit nachgebaute Nadel. Die Nadel ist NEU und nur eine Platte zum Probe bespielt hat. Alleine mmc2 Tonabnehmer kostet heutzutage ab 250 bis 500 . Der Plattenspieler befindet sich in einem sauberen Super-Zustand. Keine kratzer. Passende Tonabnehmer: mmc1, mmc2, mmc3, mmc4, mmc5. Da ist Privatverkauf. Dacher keine Garantie, keine Rcknahme.Video Selbstabholung in Dsseldorf bevorzugt. Zahlungart: Paypal-Freunde oder Überweisung. Bei PayPal-Standart Zahlung die Gebühren überniemt der Kufer.

Beogram RX2 Hebeautomatik defekt. Plattenspieler etwa von 1986. Durch eine Fachwerkstatt habe ich mitgeteilt bekommen, dass die Hebeautomatik kaputt ist. Damals hätte die Reparatur 300 € gekostet. Das war mir zu viel. Seither steht er rum und ich habe mich nun zur Abgabe entschieden. Funktion : Alles normal, aber der Tonarm rutscht nach dem ersten Lied über die Platte. Nicht enthalten: Die Tonabnehmer können einzeln gegen Gebot erworben werden. Zusätzlich ist ein weiterer Tonabnehmer vorhanden, den ich seinerzeit als Ersatz gekauft habe, weil ich noch nicht wusste woran es liegt. Dieser hat eine verbogene Nadel, funktioniert aber einwandfrei. Kann extra oder im Paket gekauft werden. 30€ extra