Item Description The DAC1 is a two-channel, 24-bit, 192-kHz Digital-to-Analog audio converter. It is, perhaps, one of the more significant recent advances in digital-audio conversion technology. Listening to audio from the DAC1 is an absolutely truthful experience. The distortion free output is so pristine you can now hear detail which was previously masked by jitter induced artifacts and distortion. If the recording was exceptional, you’ll hear it; if it wasn’t, you’ll hear that as well. The DAC1 is a 192-kHz converter, and will playback 192-kHz signals with a 52-kHz analog bandwidth. THD+N is an astonishing low -105 dB (0.00056%) measured at 0 dBFS, and -107 dB measured at -3 dBFS – at any playback frequency, at any sample rate, and with any degree of input jitter. The secret? UltraLock™ technology. Additional features include: phase-coherence between units, auto-detection and processing of pre-emphasized digital audio, and an ultrahigh performance HPA-2 headphone amplifier with dual outputs. The DAC1 has an internal, international toroidal power supply. The front panel level-control always adjusts the headphone output level. The front panel level-control can also be selected to adjust the output levels at the rear of the converter. Alternately, the output levels can be set at a fixed gain with precision, rear panel; 10-turn trim pots. The balanced output level range is +10 dBu to +29 dBu at 0 dBFS. The DAC1 is essential equipment for mastering and recording studios, broadcast facilities, even audiophile home stereo installations, and all locations that require uncolored monitoring. Features And Performance Two Channel, 24-bit, 192-kHz, D-to-A Conversion Plays 192-kHz with 52-kHz analog bandwidth Direct connection to powered monitors Total jitter immunity via UltraLock™ technology! 116 dB signal-to-noise ratio @ 48-kHz, A weighted THD+N = -107 dB (0.00045%) measured at -3 dBFS, any sample rate, any test frequency AES, S/PDIF, and Toslink inputs Digital input source-selection switch Variable or preset output level controls Balanced Low-Z XLR outputs Unbalanced RCA outputs Automatic de-emphasis for 44.1, 48, and 96-kHz when pre-emphasis bit is set Headphone amp = 0.0003% THD into 60 ? Output-off switch position for headphone-only use Front panel power and error indicating LEDs Internal low-radiation toroidal power supply International 120 - 240 input voltage range 1/2 wide, 1RU high chassis Machined aluminum front panel Rack mountable Condition This unit has been fully tested, is fully operational, and is in great aesthetic condition. Pictures are of actual item. Included This listing includes: 1 - Benchmark DAC1 (pictured) 1 - Power Cord, North American NEMA 5-15 (not pictured) Important We make every effort to accurately describe each item we sell and to give buyers the information needed to bid and buy with confidence. Item will be safely packaged prior to shipping. Item(s) are being sold AS-IS

Benchmark DAC3 HGC Digital to Analog Converter in silver. Reference stereo preamplifier, dual output headphone amplifier, PCM and DSD D/A converter in original box with remote and manual. Local Pick-up in Oakland, CA available. COSMETIC CONDITION: 9/10 FUNCTIONAL NOTES: Functions as intended and sounds great VOLTAGE: 100 - 240v, 50-60Hz SERIAL NUMBER: 20531295 ORIGINAL BOX: Yes ORIGINAL MANUAL: Yes REMOTE: Yes SHIPPING METHOD: FedEx / USPS / UPS

Benchmark DAC3 Digital to Analog ConvertersHigh-Resolution Playback Begins with an External D/A ConverterUpgrade to an external Benchmark DAC and experience the full capabilities of high-resolution audio.Sonically-Neutral Studio MonitoringBenchmark converters are designed to be sonically neutral. This sonic transparency is absolutely essential in the studio monitoring chain.Benchmark converters have become a standard fixture in many of the worlds finest studios.Bring the Studio into Your Living RoomWhen Benchmarks professional converters are used in hi-fi applications, studio-quality sound can be enjoyed in a home environment. Enjoy pure music without any coloration from the electronics. Hear the music exactly the way it was heard in the studio, and exactly the way the artists intended.Discover the natural, uncolored, analog sound of Benchmark converters.Sit in the Performance SpaceTransparent sound can go beyond replicating the studio experience. Recordings that have been produced with a natural and unprocessed sound can transport you to the performance space. Close your eyes and get ready to be transported!The experience of being there can only happen when the entire audio chain is selected for maximum transparency.Benchmark DAC3 Product FamilyEach member of the DAC3 converter family is sonically identical, and they share identical performance specifications. Each model is built on the same circuit board, but the higher-priced models add additional features.DAC3 BDigital Inputs OnlyNo Volume ControlIdeal for use with a separate preamplifier such as the LA4 or HPA4Excellent choice for professional studio applicationsThe DAC3 B to HPA4 to AHB2 signal chain is our flagship HiFi system.The DAC3 B to LA4 to AHB2 signal chain provides the same performance when a headphone amplifier is not needed.DAC3 LIncludes all of the features found on the DAC3 BAdds our Hybrid Gain Control (combined analog and digital volume control)Adds two pairs of unbalanced inputsExcellent choice when the DAC will act as the system volume control.The DAC3 L to AHB2 signal chain is our second-best signal chain.An LA4 or HPA4 can be added to the chain to raise the performance to that of our flagship system.Volume control is bypassed when an LA4 or HPA4 is addedDAC3 HGCIncludes all of the features found on the DAC3 B and DAC3 LAdds our HPA2™ headphone amplifier.An LA4 or HPA4 can be added to the chain to upgrade the performance to the top tier.Volume control is bypassed when an LA4 or HPA4 is added DAC3 TechnologiesHarmonic CompensationHybrid Gain ControlUltraLock3™ Jitter Attenuation SystemHigh-Headroom DSPMulti-Mode Asynchronous USB Audio SystemQuad 32-bit balanced D/A Conversion SystemDistributed Power RegulationHarmonic CompensationThe ES9028PRO has two distortion compensation systems that independently remove most of the 2nd and 3rd harmonic distortion in the D/A converter. Benchmarks ultra-clean analog output stages allow these systems to be fully leveraged in the DAC3. To the best of our knowledge, no other D/A converter has lower THD than the Benchmark DAC3.Hybrid Gain ControlHGC is Benchmarks unique Hybrid Gain Control system. The DAC3 combines active analog gain control, passive low-impedance attenuators, a 32-bit digital gain control, and a servo-driven volume control. All inputs are controlled by the rotary volume control. This volume control moves in response to commands from the remote control. Analog inputs are never converted to digital, and digital inputs never pass through an analog potentiometer. Digital inputs are precisely controlled in the 32-bit DSP system. The DSP system preserves precise L/R balance, and precise stereo imaging, while avoiding any source of noise and distortion.Benchmarks unique passive output attenuators provide distortion-free gain reduction without reducing the dynamic range of the converter. The attenuators optimize the gain staging between the DAC3 and the power amplifier. This optimization is absolutely essential for maximizing the dynamic range of the entire playback system. Much of the success of the DAC1 and DAC2 converters can be attributed to the passive output attenuators. Musical details can be obscured by system noise whenever a preamplifier and power amplifier are improperly matched. The HGC system will make full use of your power amplifiers dynamic range. Experience new details in your favorite recordings.UltraLock3™ Jitter Attenuation SystemUltraLock3™ is an improved version of the UltraLock2™ system used in the DAC2 product family. UltraLock3™ locks with precise phase accuracy in only 6 ms. In contrast, the UltraLock2™ system required 400 ms. Both UltraLock™ systems provide virtually perfect jitter attenuation, but the lightning-fast lock time of the new UltraLock3™ will be appreciated by many of our users.DSP processing is 32-bits, DSP headroom is 3 dB, sample rate is 211 kHz, and jitter-induced distortion and noise is at least 140 dB below the level of the music - well below the threshold of hearing. Benchmarks UltraLock3™ system eliminates all audible jitter artifacts.High Headroom DSP - with 3.5 dB Excess Digital HeadroomAll of the digital processing in the DAC3 is designed to handle signals as high as +3.5 dBFS. Most digital systems clip signals that exceed 0 dBFS. The 0 dBFS limitation seems reasonable, as 0 dBFS is the highest sinusoidal signal level that can be represented in a digital system. However, a detailed investigation of the mathematics of PCM digital systems will reveal that inter-sample peaks may reach +3.01 dBFS while individual samples never exceed 0 dBFS. These inter-sample peaks are common in commercial releases, and are of no consequence in a PCM system until they reach an interpolation process. But, for a variety of reasons, virtually all audio D/A converters use an interpolation process. The interpolation process is absolutely necessary to achieve 24-bit state-of-the art conversion performance. Unfortunately, inter-sample peaks exceeding 0 dBFS cause clipping in most interpolators. This clipping produces distortion products that are non-harmonic and non-musical . We believe these broadband distortion products often add a harshness or false high-frequency sparkle to digital reproduction. The DAC3 avoids these problems by maintaining at least 3.5 dB of headroom in the entire conversion system. We believe this added headroom is a groundbreaking improvement.Multi-Mode Asynchronous USB SystemBenchmarks USB system supports USB Audio 2.0, DSD, and USB Audio 1.1. It is frequency agile, and will follow sample rate changes initiated by the computer and/or the media playback software. In all modes the USB communications are asynchronous in order to eliminate unnecessary sources of jitter.The DAC3 has a low-jitter master clock which controls the transfer of audio data from the computer to the USB sub-system. The computer asynchronously transfers audio data to a buffer in the DAC3. The contents of the buffer are then asynchronously transferred to the D/A conversion subsystem. This second asynchronous transfer eliminates any traces of jitter that accumulate as the data is transferred between the USB and conversion subsystems. No traces of jitter-induced distortion are measurable to our measurement limits (better than -150 dBFS). This truly represents the state-of-the art. Enjoy the convenience of computer playback without compromise. The Asynchronous USB system supports USB Audio 2.0 for high-resolution 192kHz, and DSD playback. No drivers are required for MAC operating systems. An easy-to-install driver adds 192 kHz and DSD capabilities to Windows operating systems.An asynchronous, driverless USB Audio 1.1 mode supports sample rates up to 96 kHz. This USB mode can be selected from the front panel or from the remote control. The driverless USB Audio 1.1 mode allows quick plug-and-play connections to Windows, MAC, iOS, and Linux operating systems without installing drivers. Just plug in the USB, and the DAC3 becomes an available audio device.The USB subsystem remains active when the DAC3 is powered down. This prevents interruptions to the computer playback operations and eliminates the need to reconfigure the computer every time the converter is turned on.Quad 32-bit Balanced Conversion SystemFour balanced 32-bit D/A converters deliver audio to Benchmarks low-impedance current to voltage converters. The 4:1 redundancy reduces noise and distortion to levels that set new benchmarks. The conversion system at the core of the DAC3 is as good as it gets. The analog circuits that follow the D/A converter are carefully designed. Benchmark has leveraged its long history of building high-end analog audio equipment, in order to create an outstanding output stage.The conversion system in the DAC3 achieves a 6 dB signal to noise improvement through the use of 4:1 summing. The ES9028PRO D/A is an 8-channel 32-bit converter. In the DAC3, four channels are summed in the analog domain to form each of the two output channels.The 4:1 summing also improves the THD. The non-linearities in individual conversion channels are averaged across the four summed channels and incoherent non-linearities are attenuated by 6 dB.Diagnostic Tools - Sample-Rate and Word-Length IndicatorsEver wonder why that 192 kHz 24-bit download on your computer just doesnt sound right? Your media player may be down-sampling to 44.1 kHz and/or truncating to 16-bits. Many computers and media players apply poor-quality sample rate conversion and truncation. Fortunately these problems can be eliminated with the selection a good frequency-agile media player. The sample-rate and word-length displays on the DAC3 confirm the proper operation of your media player.Polarity SwitchYou may encounter recordings with inverted polarity. The DAC3 HGC and DAC3 L include a polarity switch to correct the problem.Home Theater BypassThe DAC3 can be integrated into a home theater system. Typically the DAC3 drives the left and right power amplifiers, and an analog feed from the home theater system is connected to either of the analog inputs on the DAC3. A programmable Home Theater Bypass function sets the pass-through gain to unity when the surround system is active. The DAC3 HGC and DAC3 L include an indicator light that is illuminated when bypass is active.Digital Pass ThroughThe second coaxial input on the DAC3 can be reconfigured as a digital output. In output mode, any selected digital input (including USB) will pass through to the coaxial output. The digital pass through is bit-transparent and even supports DSD (DoP 1.1). Dolby digital and DTS formats can also be passed through to a surround processor.Bi-Directional 12 Volt TriggerBenchmark re-invents the 12 volt trigger. The trigger connection on the DAC2 can be used as an input, an output, or both. It is compatible with any common 12 volt trigger input or output. The trigger can be used to turn a power amplifier on or off automatically. The DAC3 will also respond to a 12 volt trigger to follow the actions of another audio component.Power SwitchThe power switch can place the DAC3 in standby, or full shut down. In full shut down, the unit will still respond to the trigger input and the IR remote control. Power consumption is less than 0.5 W in full shut down.Low Power ConsumptionThe DAC3 uses high-efficiency low noise power supplies and may be operated from any standard international voltage without adjustment. Power consumption is 12 W typical.Distributed Power RegulationTo achieve the lowest possible noise, the DAC3 uses distributed power supply regulation. Each critical subsystem has at least one dedicated low-noise voltage regulator.HPA2™ Headphone Power AmplifierThe DAC3 features the HPA2™ - Benchmarks signature high-current, 0-Ohm headphone power amplifier. The HPA2™ is arguably the ultimate reference headphone power amplifier. It will deliver the full rated performance of the DAC3 to the headphones. The DAC3 has two 1/4 headphone jacks on the front panel. The performance of the HPA2™ remains consistent even when two headphones are being driven simultaneously.

Benchmark DAC3 Digital to Analog ConvertersHigh-Resolution Playback Begins with an External D/A ConverterUpgrade to an external Benchmark DAC and experience the full capabilities of high-resolution audio.Sonically-Neutral Studio MonitoringBenchmark converters are designed to be sonically neutral. This sonic transparency is absolutely essential in the studio monitoring chain.Benchmark converters have become a standard fixture in many of the worlds finest studios.Bring the Studio into Your Living RoomWhen Benchmarks professional converters are used in hi-fi applications, studio-quality sound can be enjoyed in a home environment. Enjoy pure music without any coloration from the electronics. Hear the music exactly the way it was heard in the studio, and exactly the way the artists intended.Discover the natural, uncolored, analog sound of Benchmark converters.Sit in the Performance SpaceTransparent sound can go beyond replicating the studio experience. Recordings that have been produced with a natural and unprocessed sound can transport you to the performance space. Close your eyes and get ready to be transported!The experience of being there can only happen when the entire audio chain is selected for maximum transparency.Benchmark DAC3 Product FamilyEach member of the DAC3 converter family is sonically identical, and they share identical performance specifications. Each model is built on the same circuit board, but the higher-priced models add additional features.DAC3 BDigital Inputs OnlyNo Volume ControlIdeal for use with a separate preamplifier such as the LA4 or HPA4Excellent choice for professional studio applicationsThe DAC3 B to HPA4 to AHB2 signal chain is our flagship HiFi system.The DAC3 B to LA4 to AHB2 signal chain provides the same performance when a headphone amplifier is not needed.DAC3 LIncludes all of the features found on the DAC3 BAdds our Hybrid Gain Control (combined analog and digital volume control)Adds two pairs of unbalanced inputsExcellent choice when the DAC will act as the system volume control.The DAC3 L to AHB2 signal chain is our second-best signal chain.An LA4 or HPA4 can be added to the chain to raise the performance to that of our flagship system.Volume control is bypassed when an LA4 or HPA4 is addedDAC3 HGCIncludes all of the features found on the DAC3 B and DAC3 LAdds our HPA2™ headphone amplifier.An LA4 or HPA4 can be added to the chain to upgrade the performance to the top tier.Volume control is bypassed when an LA4 or HPA4 is added DAC3 TechnologiesHarmonic CompensationHybrid Gain ControlUltraLock3™ Jitter Attenuation SystemHigh-Headroom DSPMulti-Mode Asynchronous USB Audio SystemQuad 32-bit balanced D/A Conversion SystemDistributed Power RegulationHarmonic CompensationThe ES9028PRO has two distortion compensation systems that independently remove most of the 2nd and 3rd harmonic distortion in the D/A converter. Benchmarks ultra-clean analog output stages allow these systems to be fully leveraged in the DAC3. To the best of our knowledge, no other D/A converter has lower THD than the Benchmark DAC3.Hybrid Gain ControlHGC is Benchmarks unique Hybrid Gain Control system. The DAC3 combines active analog gain control, passive low-impedance attenuators, a 32-bit digital gain control, and a servo-driven volume control. All inputs are controlled by the rotary volume control. This volume control moves in response to commands from the remote control. Analog inputs are never converted to digital, and digital inputs never pass through an analog potentiometer. Digital inputs are precisely controlled in the 32-bit DSP system. The DSP system preserves precise L/R balance, and precise stereo imaging, while avoiding any source of noise and distortion.Benchmarks unique passive output attenuators provide distortion-free gain reduction without reducing the dynamic range of the converter. The attenuators optimize the gain staging between the DAC3 and the power amplifier. This optimization is absolutely essential for maximizing the dynamic range of the entire playback system. Much of the success of the DAC1 and DAC2 converters can be attributed to the passive output attenuators. Musical details can be obscured by system noise whenever a preamplifier and power amplifier are improperly matched. The HGC system will make full use of your power amplifiers dynamic range. Experience new details in your favorite recordings.UltraLock3™ Jitter Attenuation SystemUltraLock3™ is an improved version of the UltraLock2™ system used in the DAC2 product family. UltraLock3™ locks with precise phase accuracy in only 6 ms. In contrast, the UltraLock2™ system required 400 ms. Both UltraLock™ systems provide virtually perfect jitter attenuation, but the lightning-fast lock time of the new UltraLock3™ will be appreciated by many of our users.DSP processing is 32-bits, DSP headroom is 3 dB, sample rate is 211 kHz, and jitter-induced distortion and noise is at least 140 dB below the level of the music - well below the threshold of hearing. Benchmarks UltraLock3™ system eliminates all audible jitter artifacts.High Headroom DSP - with 3.5 dB Excess Digital HeadroomAll of the digital processing in the DAC3 is designed to handle signals as high as +3.5 dBFS. Most digital systems clip signals that exceed 0 dBFS. The 0 dBFS limitation seems reasonable, as 0 dBFS is the highest sinusoidal signal level that can be represented in a digital system. However, a detailed investigation of the mathematics of PCM digital systems will reveal that inter-sample peaks may reach +3.01 dBFS while individual samples never exceed 0 dBFS. These inter-sample peaks are common in commercial releases, and are of no consequence in a PCM system until they reach an interpolation process. But, for a variety of reasons, virtually all audio D/A converters use an interpolation process. The interpolation process is absolutely necessary to achieve 24-bit state-of-the art conversion performance. Unfortunately, inter-sample peaks exceeding 0 dBFS cause clipping in most interpolators. This clipping produces distortion products that are non-harmonic and non-musical . We believe these broadband distortion products often add a harshness or false high-frequency sparkle to digital reproduction. The DAC3 avoids these problems by maintaining at least 3.5 dB of headroom in the entire conversion system. We believe this added headroom is a groundbreaking improvement.Multi-Mode Asynchronous USB SystemBenchmarks USB system supports USB Audio 2.0, DSD, and USB Audio 1.1. It is frequency agile, and will follow sample rate changes initiated by the computer and/or the media playback software. In all modes the USB communications are asynchronous in order to eliminate unnecessary sources of jitter.The DAC3 has a low-jitter master clock which controls the transfer of audio data from the computer to the USB sub-system. The computer asynchronously transfers audio data to a buffer in the DAC3. The contents of the buffer are then asynchronously transferred to the D/A conversion subsystem. This second asynchronous transfer eliminates any traces of jitter that accumulate as the data is transferred between the USB and conversion subsystems. No traces of jitter-induced distortion are measurable to our measurement limits (better than -150 dBFS). This truly represents the state-of-the art. Enjoy the convenience of computer playback without compromise. The Asynchronous USB system supports USB Audio 2.0 for high-resolution 192kHz, and DSD playback. No drivers are required for MAC operating systems. An easy-to-install driver adds 192 kHz and DSD capabilities to Windows operating systems.An asynchronous, driverless USB Audio 1.1 mode supports sample rates up to 96 kHz. This USB mode can be selected from the front panel or from the remote control. The driverless USB Audio 1.1 mode allows quick plug-and-play connections to Windows, MAC, iOS, and Linux operating systems without installing drivers. Just plug in the USB, and the DAC3 becomes an available audio device.The USB subsystem remains active when the DAC3 is powered down. This prevents interruptions to the computer playback operations and eliminates the need to reconfigure the computer every time the converter is turned on.Quad 32-bit Balanced Conversion SystemFour balanced 32-bit D/A converters deliver audio to Benchmarks low-impedance current to voltage converters. The 4:1 redundancy reduces noise and distortion to levels that set new benchmarks. The conversion system at the core of the DAC3 is as good as it gets. The analog circuits that follow the D/A converter are carefully designed. Benchmark has leveraged its long history of building high-end analog audio equipment, in order to create an outstanding output stage.The conversion system in the DAC3 achieves a 6 dB signal to noise improvement through the use of 4:1 summing. The ES9028PRO D/A is an 8-channel 32-bit converter. In the DAC3, four channels are summed in the analog domain to form each of the two output channels.The 4:1 summing also improves the THD. The non-linearities in individual conversion channels are averaged across the four summed channels and incoherent non-linearities are attenuated by 6 dB.Diagnostic Tools - Sample-Rate and Word-Length IndicatorsEver wonder why that 192 kHz 24-bit download on your computer just doesnt sound right? Your media player may be down-sampling to 44.1 kHz and/or truncating to 16-bits. Many computers and media players apply poor-quality sample rate conversion and truncation. Fortunately these problems can be eliminated with the selection a good frequency-agile media player. The sample-rate and word-length displays on the DAC3 confirm the proper operation of your media player.Polarity SwitchYou may encounter recordings with inverted polarity. The DAC3 HGC and DAC3 L include a polarity switch to correct the problem.Home Theater BypassThe DAC3 can be integrated into a home theater system. Typically the DAC3 drives the left and right power amplifiers, and an analog feed from the home theater system is connected to either of the analog inputs on the DAC3. A programmable Home Theater Bypass function sets the pass-through gain to unity when the surround system is active. The DAC3 HGC and DAC3 L include an indicator light that is illuminated when bypass is active.Digital Pass ThroughThe second coaxial input on the DAC3 can be reconfigured as a digital output. In output mode, any selected digital input (including USB) will pass through to the coaxial output. The digital pass through is bit-transparent and even supports DSD (DoP 1.1). Dolby digital and DTS formats can also be passed through to a surround processor.Bi-Directional 12 Volt TriggerBenchmark re-invents the 12 volt trigger. The trigger connection on the DAC2 can be used as an input, an output, or both. It is compatible with any common 12 volt trigger input or output. The trigger can be used to turn a power amplifier on or off automatically. The DAC3 will also respond to a 12 volt trigger to follow the actions of another audio component.Power SwitchThe power switch can place the DAC3 in standby, or full shut down. In full shut down, the unit will still respond to the trigger input and the IR remote control. Power consumption is less than 0.5 W in full shut down.Low Power ConsumptionThe DAC3 uses high-efficiency low noise power supplies and may be operated from any standard international voltage without adjustment. Power consumption is 12 W typical.Distributed Power RegulationTo achieve the lowest possible noise, the DAC3 uses distributed power supply regulation. Each critical subsystem has at least one dedicated low-noise voltage regulator.HPA2™ Headphone Power AmplifierThe DAC3 features the HPA2™ - Benchmarks signature high-current, 0-Ohm headphone power amplifier. The HPA2™ is arguably the ultimate reference headphone power amplifier. It will deliver the full rated performance of the DAC3 to the headphones. The DAC3 has two 1/4 headphone jacks on the front panel. The performance of the HPA2™ remains consistent even when two headphones are being driven simultaneously.

This is a high-quality Benchmark DAC 1 Headphone Amplifier in black. Its perfect for music lovers who want to enjoy excellent audio quality. This amplifier has two inputs and two outputs, including a headphone jack, stereo RCA output, and XLR output. It supports various audio inputs, such as digital optical TOSLINK and coaxial RF/F-type, making it a versatile addition to any home audio setup. The Benchmark brand is known for producing high-performance audio equipment, and this DAC 1 is no exception. Whether youre looking to upgrade your listening experience or want to add an amplifier to your home theater system, this Benchmark DAC 1 is an excellent choice. Fully Operational! https://www.soundonsound.com/reviews/benchmark-dac1

Selling a mint condition, flawless performing Benchmark DAC2 HGC Preamp/Headphone Amp. Purchasing an all-in-one streamer as a replacement. This unit was used in a 2 channel hi-fi system. Non smoking, no pets, no kids, low dust environment. Also includes Remote control Power cordConditionPhysical - Like new. No visible cosmetic defectsPerformance - Like new Features Sample Frequencies: 28 to 210 kHz (Coaxial Inputs)8 to 96 kHz (Optical Inputs)44.1, 48, 88.2, 96, 176.4, 192 kHz (USB Input)Bit depth: 24 bitsDigital inputs: 5 (1 USB, 2 Optical, 2 Coaxial)Analog inputs: 2 RCABalanced outputs: 2 channel XLRUnbalanced outputs: 2 RCA (2 x 2 channel)Headphone outputs: 2 (1/4 TRS)Manufacturers Description New TechnologiesHybrid Gain ControlHigh-Headroom DSPUltraLock2™ Jitter Attenuation SystemQuad 32-bit balanced D/A Conversion SystemMulti-Mode Asynchronous USB Audio SystemDistributed Power RegulationReference Performance The DAC2 is Benchmarks second-generation 2-channel D/A converter. The DAC2 converter has lower noise and lower distortion than Benchmarks DAC1 converter.The performance of the DAC2 exceeds the measurement limits of some of todays best test equipment. The DAC2 delivers outstanding musical detail and precise stereo imaging. It employs an advanced high-headroom digital filter design, and a new high-sample-rate Asynchronous USB Audio interface. All inputs are fully isolated from interface jitter by Benchmarks new UltraLock2™ jitter attenuation system. Internal digital processing and conversion is 32-bits, and this processing includes 3.5 dB of headroom above 0 dBFS. This headroom prevents the DSP overloads that commonly occur in other D/A converters. Four balanced 32-bit D/A converter are summed together to create each balanced analog output. This 4:1 summation provides a 6 dB noise reduction, and gives the DAC2 industry-leading performance. Native DSD Conversion All digital inputs on the DAC2 support native PCM or DSD conversion. From any input, DSD is transported with bit accuracy over DoP 1.1. DSD and PCM are both natively converted to analog. There are no DSD to PCM or PCM to DSD conversions to compromise the quality of the music. The DAC2 conversion system seamlessly switches between native PCM and native DSD conversion. DSD over DoP 1.1 is supported by many media players, and DSD downloads are now available from several sources. Direct Connectivity to Power Amplifiers Benchmark DAC1 and DAC2 converters are designed to directly drive power amplifiers and speakers. Benchmark converters feature adjustable low-impedance passive attenuators at the XLR outputs that can be used to optimize the interface to the power amplifier (or powered monitor). This unique Benchmark feature optimizes the gain staging between the DAC and the power amplifier. Proper gain staging cannot be overemphasised. When audio stages are properly matched, each component in the audio chain is able to operate at its optimum signal level, and the system performance is significantly improved. Sonically-Neutral Studio Monitoring All Benchmark converters are designed for maximum transparency. This transparency is absolutely essential in the studio monitoring chain. For this reason, DAC2 converters are ideal for critical reference-quality professional systems. Unlike many competing products, the DAC2 is not designed to add euphonic coloration to the audio. Instead it is designed to be as uncolored and natural as possible.

Retiring my hifi system. This is the original, incredible sounding DAC1 from Benchmark. Fully working with the original rack mount brackets. Operates with RCA unbalanced, XLR balanced, or both. You can use one as a subwoofer output

For sale is a Benchmark DAC2 HGC DAC/preamp. It is an excellent condition, and comes with original packaging, remote, and power cord. This DAC received great reviews from many high end audio publications, including Stereophile. Experience high-quality audio with the benchmark DAC2 HGC amplifier. Built with advanced technology, it delivers crystal-clear sound that is sure to enhance your listening experience. The brand ensures its reliability and durability, making it a great investment for music enthusiasts. This amplifier is perfect for those who want to enjoy every detail of their music. With its sleek design and exceptional performance, the benchmark DAC2 HGC is a must-have for anyone who appreciates premium-quality audio.

Benchmark DAC 1 Pre combination pre amp headphone amp and 24 bit 192 khz digital to analog converter. Please note the USB input is limited to 24bit 96khz. Features fixed or variable analog unbalanced RCA and balanced XLR outputs as well as two 1/4 inch headphone jacks. Inputs include USB 2.0, optical toslink, 3 coaxial digital, and one pair of analog stereo RCA connectors. The front volume control is a fully analog high quality Alps brand. The headphones outputs are always variable while the rear balanced XLR and unbalance RCA outputs are selectable as fixed or variable. The versatility of the Benchmark is truly great. I used it in both a headphone setup and in my main home stereo system with excellent results. This is a Stereophile Class A recommend component as are each of its offspring. It offers a highly detailed and layered sound that competes well above its price point. Of all the Benchmark DAC 1 options. The PRE and HDR offer the most versatility and were the last versions of the DAC1 before being replaced by the DAC2. The HDR simply offers a remote control which the PRE does not. This unit is in excellent condition overall with no scratches or dings anywhere on it. The only thing I see that keeps it from being mint is the n in the analog input lettering is partially missing (see photos). Everything functions as it should and it sounds excellent. The original power cord is included. There is no documentation or original packaging but it will be securely packaged for shipping. I will accept offers above my initial listing price if you wish to purchase this before any bids are placed. Once a bid is placed this option will disappear. Please check my feedback and purchase with confidence. Thank you for your interest.

Der Benchmark DAC 1 USB ist ein hochwertiger Digital-Analog-Wandler für audiophile Musikliebhaber. Er bietet eine präzise und transparente Klangqualität, die durch seine hohe Auflösung und geringe Verzerrung erreicht wird. Mit seiner USB-Schnittstelle ist er ideal für die Verbindung mit Ihrem Computer oder Laptop geeignet. Das elegante Design und die robuste Bauweise machen ihn zu einem perfekten Begleiter für zu Hause und unterwegs. Er ist einfach zu bedienen und verfügt über eine Vielzahl von Anschlüssen für verschiedene Audioquellen. Der Benchmark DAC 1 USB ist eine ausgezeichnete Wahl für jeden, der seine Musik in höchster Qualität genießen möchte.

Benchmark DAC 1 Pre combination pre amp headphone amp and 24 bit 192 khz digital to analog converter. Please note the USB input is limited to 24bit 96khz. Features fixed or variable analog unbalanced RCA and balanced XLR outputs as well as two 1/4 inch headphone jacks. Inputs include USB 2.0, optical toslink, 3 coaxial digital, and one pair of analog stereo RCA connectors. The front volume control is a fully analog high quality Alps brand. The headphones outputs are always variable while the rear balanced XLR and unbalance RCA outputs are selectable as fixed or variable. The versatility of the Benchmark is truly great. I used it in both a headphone setup and in my main home stereo system with excellent results. This is a Stereophile Class A recommend component as are each of its offspring. It offers a highly detailed and layered sound that competes well above its price point. Of all the Benchmark DAC 1 options. The PRE and HDR offer the most versatility and were the last versions of the DAC1 before being replaced by the DAC2. The HDR simply offers a remote control which the PRE does not. This unit is in excellent condition overall with no scratches or dings anywhere on it. The only thing I see that keeps it from being mint is the n in the analog input lettering is partially missing (see photos). Everything functions as it should and it sounds excellent. The original power cord is included. There is no documentation or original packaging but it will be securely packaged for shipping. I will accept offers above my initial listing price if you wish to purchase this before any bids are placed. Once a bid is placed this option will disappear. Please check my feedback and purchase with confidence. Thank you for your interest.

Up for sale is a Benchmark DAC3 HGC D/A Audio Converter Remote in excellent condition. This is the original remote. Tested and working. Please feel free to email me with any questions you may have. Thanks in advance for your purchase.

Amazing DAC from Benchmark Media USA. In as new condition with original Box. Sounds amazing. Please see the Benchmark site for all specs. Capable of high Pro Output. Includes two installed Synergistic Research Quantum Orange Fuses. $375 value. Setup picture is for reference only headphones and amp not included. Ships double boxed with Original Box / Manual insured, signature required on delivery

Great condition fully working Comes with power cord.

Benchmark DAC3 HGC DAC Headphone Amp Preamp (Used). Black faceplace. Excellent condition, works perfect (selling due to owning multiple DAC3, downsizing gear). Including a Benchmark remote, 12v trigger cable, USB cable, locking power cable (sold by Benchmark). Original packaging w/ instructions & spare fuses.

We have this preowned Benchmark DAC3L DAC pre-amplifier in black. The unit is in excellent condition with hardly any discernible cosmetic marks or scratches. It comes with its UK and EU mains leads, remote control, 3.5mm 12V trigger cable, user manual and replacement fuses, as well as its original packaging. Unit Serial Number: 19310176-0 - manufactured 9th October 2019 £20 Mainland UK Delivery Any queries please do not hesitate to contact us. TI-1-64771-910009 Auction items can be viewed and demoed if practical at our demo rooms in Hull, please make an appointment in advance. Fanthorpes Hifi is based in a stunning Edwardian Arcade in Hull East Yorkshire. There are no pressure sales, we only sell the brands we believe in and always put the customer first. We are specialists in CHORD, PMC, Bryston, Devialet, Arcam, Musical Fidelity, Martin Logan amongst others please check our website for more details. HS

Enhance your audio experience with this high-quality Benchmark DAC-1 Black Digital to Analog converter. The device comes with a power cord for easy installation and operation. See my other auctions for a Lynx Aurora8 8 channel converter, Aurora LT-ADAT and a RME 9652 interface card and accessories for a great complete recording system! This came directly from a working setup but is sold as is with no warranty. But bid with confidence, I have over 20 years and 100% positive feedback on eBay.

Benchmark DAC1 - D/A Wandler der Referenz-Klasse für Studio oder Zuhause. gebrauchtim Originalkartonehemaliger Neupreis: 1000€leichte Abdrücke auf dem Deckel (siehe Fotos)Kaltgeräte-Stromkabel wird beigelegtDeutsche und englische BedienungsanleitungPrivatverkauf. Keine Gewährleistung oder Garantie.Hervorragende Tests in der echten Fachpresse (Professional Audio, SoundOnSound etc.). Verkauf wegen Umstieg auf rein digitales Heimkino. Technische Daten Two Channel, 24-bit, 192-kHz, D-to-A Conversion Plays 192-kHz with 52-kHz analog bandwidth Direct connection to powered monitors Total jitter immunity via UltraLockTM technology! 116 dB signal-to-noise ratio @ 48-kHz, A weighted THD+N = -107 dB (0.00045%) measured at -3 dBFS, any sample rate, any test frequency AES, S/PDIF, and Toslink inputs Digital input source-selection switch Variable or preset output level controls Balanced Low-Z XLR outputs Unbalanced RCA outputs Automatic de-emphasis for 44.1, 48, and 96-kHz when pre-emphasis bit is set Headphone amp = 0.0003% THD into 60 ? Output-off switch position for headphone-only use Front panel power and error indicating LEDs Internal low-radiation toroidal power supply International 120 - 240 input voltage range 1/2 wide, 1RU high chassis Machined aluminum front panel

Reference quality 2-Channel 24-bit 192-kHz Digital-to-Analog Audio Converterwith Preamp Functions and USB InputHPA2 high current headphone outputsRCA and balanced XLR outputsToroidal power transformer½ Rack Wide, 1 RU HighIncludes DAC, cables, original box, extra fuses, and manual Thanks for looking!

Benchmark DAC-1 Digital To Analog Player Black. Unit is in very good condition and function Perfectly. Comes with power cord. Benchmark DAC-1 Black Digital To Analog Player With Power Cord Description Our SKU: EEUS004157696ES-P3CSG4P Item Brand: Benchmark Item MPN: 86787 Benchmark DAC-1 Digital To Analog Player Black. Unit is in very good condition and function Perfectly. Comes with power cord. Please let us know if you have any questions regarding a past or future purchase. Check out our entire store for more great products and deals!! Warranty Our inventory is purchased from various different manufacturers, retailers, and 3rd party sources. We do not represent or make any claim regarding any manufacturers warranty. We do however make every possible attempt to accurately describe the inventory we sell and stand behind it. We offer a no-questions asked 30-day return policy on everything we sell if the item is in the same condition it was sold in. If you have any issues at all with your purchase please feel free to contact us, we want to make it right!! Shipping All items are carefully packed and properly protected for shipment. We use several different carriers and choose the most economical for the item and destination based on the estimated handling and transit time. Please make every attempt possible to verify that part/product being purchased is correct for your application In the event of shipping damage, item not as expected, or any other reason to desire to return the product, please feel to contact us. At this time we do not offer internation shipping. About 8TEN Industries Since 2016, 8TEN Industries has been a leading asset recovery provider supporting national retailers, brands, and manufacturers. Our 60,000 square foot processing and distribution facility located in Cass City, Michigan has allowed us to become industry leader in turning difficult problems for manufacturers into great deals for our customers. More Items Store Contact Follow Us 8TEN Industries

In like new conditions, use as pre amplifier/dac or both.

The worlds largest online retailer of pre-owned audio Product DescriptionWho we areWhat we doOur ProcessOur Policies Benchmark DAC1 DAC; D/A Converter; Black Product SKU: 49783 Voltage: 115V/230V # of Owners: 1 Service History: None Serial Number: 40865 Age: Unknown Tobacco Exposure: No MSRP: $995 Cosmetic Description: Good cosmetic condition with some minor visible cosmetic wear including light scratches on the top surface, along with a couple light nicks on the faceplate and the top edge of the faceplate. This item has some very light wear but still presents like new from your listening position. What is Included: DAC, Coaxial adapter, Power cable Other Notes: Listening to audio from the DAC1 is an absolutely truthful experience. The distortion free output is so pristine you can now hear detail which was previously masked by jitter induced artifacts and distortion. If the recording was exceptional, you’ll hear it; if it wasn’t, you’ll hear that as well. - Benchmark Functional Notes: Operational condition of this item is excellent, fully tested and no issues found. Shipping: Cost to ship this item within the contiguous United States is a flat rate of $23- including packaging and insurance. For all other locations including Hawaii, Puerto Rico and Alaska, please request a quote prior to purchase. Items with factory packaging will be double boxed. When factory packaging not available re-usable shipping box with custom injected-foam mold will be used. (for all items over 10 lbs). Note that all items valued over $750 will require a signature upon delivery. Your online source for the best value in new and used audio gear. Visit us online to Buy / Sell / Trade / Consign The Music Room is the largest online retailer of pre-owned HiFi equipment in the world. Headquartered in beautiful Boulder Colorado, The Music Room is a team of 17 strong (and growing) music lovers - all dedicated to one singular mission: delivering the very best online shopping experience in the audio industry - period. We specialize in well-cared for, previously used gear because that is what we are passionate about. We feel that there is nothing more fulfilling than creating a high-performance system on a budget with carefully selected used components, speakers and cables. Our program is safe, secure, fast, fair, hassle-free and highly effective. Visit us online to Buy / Sell / Trade / Consign Buy: Are you looking to get a fair price for your used home audio equipment without all the hassles, headaches, risks and fees? We will appraise your equipment and make you a quick, easy, fair cash offer. Just fill out our “get a quote” form on our homepage to start the process. Sell: We sell in multiple online venues with many (but not all) of our products available in our eBay store. Everything is quality-assured and backed by our best-in-class, satisfaction-guaranteed return policy. Trade: Make your budget go further with a generous trade-in allowance. Let us know what you have available, and we’ll get you the best possible trade-in allowance. We can even assist with shipping & logistics from anywhere in the USA. Just fill out our “get a quote” form on our homepage to start the process. Consign: We offer a hassle-free way for individuals and businesses to liquidate used gear. We’ll handle every step of the process from shipping to appraisals, customer service, fulfillment, and returns: Industry-low rates with no hidden fees Leverage our world-class reputation and get exposure in multiple sales venues - putting your product in front of over 570k monthly shoppers. Our program is Safe, Secure, Fast, Fair, Hassle-Free and Highly Effective. With 100% feedback ratings in every venue in which we sell, you can rest assured that we’ve got your back. Visit us online to Buy / Sell / Trade / Consign Quality Assurance: We offer 15-20 new product listings for sale daily. Each product undergoes an extremely rigorous quality-assurance and listening session by one of our qualified technicians. We understand that buying used audio equipment can be rife with uncertainty and unexpected headaches. Our quality assurance program is informed by a knowledge-base built through delivering over 30,000 used audio products to satisfied customers. We promise to deliver your product in good working order - exactly as described 100% of the time. Support: We don’t just make promises. We stand behind them - your satisfaction is guaranteed. Our support team is ready to help you with any questions you might have before and after the sale. Value: In the never-ending pursuit of high performance, it’s important to stretch your limited budget as far as possible. Used equipment sells for a fraction of new prices, and with a partner like The Music Room you can upgrade any time you like and get most of your money back. There’s simply no better way to maximize a limited audio budget. Packaging: We’ve invested thousands of dollars and countless hours into mastering our state-of-the-art packaging process. Our custom foam-in-place packaging system allows us to safely package almost any item regardless of irregular shapes or sizes. Most importantly, this system provides our customers with a re-usable shipping box which increases the resale value of the product and provides a shipping method for easy, secure returns. Be seen by over 70,000 monthly visitors. Visit us online to Buy / Sell / Trade / Consign Payment: Prompt payment is expected. Paypal is preferred but all forms of payment are accepted. Unpaid item case will be opened after 3 days if no payment received. Shipping Times: Most Domestic orders ship within 1 business day of purchase. For International orders or freight shipments, please allow 2-3 business days. In all cases, tracking information will be emailed to you at the moment the shipping label is created. If you cant find it or have other questions about shipping & logistics, please contact us. Shipping Costs: Flat rate shipping costs are applicable within the contiguous 48 States (USA). These rates are clearly posted on each product page. For an International or custom quote (including Hawaii, PR, AK) please contact us. Returns: Every purchase made on eBay carries a 30-day, satisfaction-guaranteed return policy. If youre not happy with your purchase for any reason or if youve simply changed your mind... no problem. Simply ship it back for a full refund or exchange (minus S&H costs). If you have received an item that is defective in some way, we will make it right. Let us know - we will pay for return shipping and repair the item or refund 100% of your original purchase price.