2 stereo amplifiers in the listing. One has been significantly upgraded by the factory Monoblock takes the power up to 400w in 8 ohms

Classic audiophile preamp from Bel Canto Design. This unit was recently inspected and serviced by Matt Cramer of Ace Tomato Audio, the Bel Canto Design factory-authorized service center, who gave it a full bill of health: I started by running some frequency tests and all looks good. Basically the unit measure perfectly flat. ... You’ve got a late Rev B unit thats a perfect candidate for upgrades. Im happy to share the upgrade options Matt suggested. There is a small blemish at the rear of the top of the unit, so I cant call it mint, but it is in excellent condition. A manual and power cable are included, as is an aftermarket preprogrammed remote. (Other remote options ranging from original to aftermarket, and from $800 to $300, are available from Ace Tomato.) Im also throwing in two WBC XLR cables (Canare Cable, Neutrik connector) to take advantage of the units balanced connections. The Pre1 comes double boxed in factory packaging. Specifications Volume setting for unity gain • 84 Input overload • 5 Volts rms Bandwidth Into >600 Ohms • 0 Hz-200 kHz Signal to Noise Ratio re 1 volt out • >100 dB A weighted, 20-20KHz Distortion at 1 Volts rms Out • <0.01% Input configuration and impedance • Single-ended/balanced 20K ohm Output Options • 2-XLR Balanced; 2-RCA; 1-buffered RCA Tape Out Output Impedance • 50 ohms Maximum Output Level • 10 volts rms Balanced Gain Single-ended • 16 dB Gain Balanced • 16 dB Power Requirements • 100-120 VAC 50-60 Hz or 230-240 VAC 50-60 Hz 25VA Size • 17.5”W x 15”D x 4”H (mm x mm x mm) Weight • 14lbs. (6.5kg) The Pre1 output stage uses the latest integrated technology to combine multiple amplifiers and Laser trimmed precision resistors in a true balanced output stage. This balanced stage mimics the operation of a transformer, providing ideal line-level audio drive into either a balanced or single-ended load. This operation eliminates ground loop issues with power amplifiers when used with either the RCA outputs or the XLR. This assures maximum signal to noise and extremely low distortion with the shortest audio signal path. The power supply uses a separate low noise regulation for each channel’s gain stage. Audio grade decoupling capacitors, star grounding and careful signal routing insure that low-level signals are preserved. The volume control is a precision Crystal 3310 potentiometer controlled by a microcontroller. This device provides extremely low noise and distortion coupled with high accuracy. We have found the sonic quality to be as good as or better than the best potentiometers and switched attenuators with a long useful life and no wear The input processing provides two (2) true balanced input connections and three (3) RCA jack connections plus Tape In. The Tape Output is an RCA output with an active audio-grade buffer preamplifier to isolate the internal signal bus from the tape output. The main outputs are a single-ended RCA and a balanced connection for use with balanced cables and power amplifier inputs. The elegant simplicity of the signal path and gain stage allows the Pre1 to preserve the audio signal quality.

Selling my robust, high power, Bel Canto mono block amp I had used to drive my B&W center channel . Unit is in excellent esthetic and operating condition. Selling because I had installed a big Marantz AMP10 and no longer need this one. All original power cord, factory boxing, and packaging used to ship.Description: Solid-statemonoblock power amplifier with class-D output stage. Input: single-ended RCA orbalanced XLR. Output: one set WBT 5-way safety binding posts. Power Output:>500W into 8 ohms (27.8dBW), >1000W into 4 ohms (27.8dBW). Minimum Load:2 ohms. Voltage gain: 27dB (single ended or balanced input). Peak OutputCurrent: 45A. Frequency Response: 20Hz–20kHz, ±0.5dB all loads. THD+N: 0.007%1W, 1KHz, 4 ohms. IMD (CCIF): 0.0007%, 1W, 14:15KHz, 4 ohms. Output noise: 90µVRMS A-weighted, 10Hz–20kHz. Damping factor: >1000. Output Impedance at100Hz: <8 milliohms. Input impedance: 100k ohms (RCA), 200k ohms (XLR).Input Voltage for Max Output: 3V RMS.The front panels single LED indicates whenthe amp is powered on. Bel Canto uses Bang & Olufsens 1000ASP ICEpowermodules, but with improvements in mechanical damping, parts selection, andfiltering of the residual switching noise present at the amplifiers output. Dimensions: 8.5(216mm) W by 3.5 (88mm) H by 12 (305mm) D. Weight: 18.5 lbs (9kg). Serial number of unit for sale : RI-717

The Bel Canto C5i is a very well reviewed, nice sounding, compact and attractive 60 watt integrated amplifier. Only one owner (me). I bought it new in 2011 at Stereo Exchange in NYC. Excellent condition. I do not have the original packaging but it includes the manual, remote, and power cord. Located in near Charlottesville, Virginia if you want to pickup locally. Otherwise Ill box it up and you pay shipping.

I sell my Bel Vanto DAC 3 in a very good condition. It can be used as a preamplifier, too. I use to have it connected to my Wadia a315 amplifier. Everything works properly. You receive: - Bel Canto DAC 3 - Power cable The unit will be very good packed. For buyers outside EU, please ask me about shipping costs before the purchase. Private sell. No guarantees and return.

Bel Canto e.One Phono 3 + VBL1 High-End Phonovorstufe mit Netzteil Beschreibung Mit der Phonovorstufe e.One Phono 3 des Herstellers Bel Canto erhalten Sie einen absoluten Phono-Traum! Dank der Vielzahl an Gain Settings gelingt es dem Phono 3 mit absolut jedem Tonabnahmersystem zu harmonieren. Mit dem Mäuseklavier auf der Rückseite lässt sich die Phonovorstufe ein Ihr persönliches System perfekt anpassen, sodass Sie das absolut Beste aus Ihrem Phono-Setup herausholen können! Dank dem externen Netzteil VBL1 bleibt jedoch die Phonovorstufe frei von Störrenden vibrationen und kann auf absoluter Top-Leistung abliefern. TECHNISCHE DATEN: Bandwidth: 1Hz-50KHz RIAA Accuracy: 20Hz-20KHz +/- 0.2 dB Signal to Noise Ratio 40 dB gain: >80 dB A weighted, re 5mV RMS in Distortion @ 2 Volt RMS/1kHz: <0.01% Maximum Output Level: 9.5 V RMS Output Impedance: 100 Ohms single ended Input Impedance: 47K Ohms nominal (all Resistor Switches UP) Gain Level Options: 40 dB (100X) and 60 dB (1000X) Power On usage: >10W Power Off usage: 0.0W Internally Set Operating Voltages (LNS1 or VBS1): 100-120VAC or 230-240VAC 50/60 Hz Maße (H x B x T): 7,5 x 21,6 x 31,8 cm Gewicht: 4,5 kg Zustand und Zubehör Die e.One Phono 3 und das VBL1 Netzteil befindet sich in einem makellosen Zustand! Verpackung und Versand Sicherer Versand in der Originalverpackung. Differenzbesteuert gemäß §25a UStG. - keine MwSt. ausweisbar! Sie erhalten beim Kauf eine Gewährleistung von 12 Monaten! Achtung: Bei Abholung ist keine Zahlung via PayPal möglich! Suchen Sie ein High-End Gerät, wollen aber nicht neu kaufen? Sie möchten sich aber sicher sein, High-End im bestmöglichsten Zustand für Ihr Geld zu bekommen? Dann sind Sie bei uns richtig. Sie finden bei uns Vollverstärker, Endverstärker, Monoblöcke, Röhrengeräte, CD-Player, Plattenspieler, Receiver, Tuner und natürlich Lautsprecher. Sollten wir einmal etwas nicht im Programm haben, erteilen Sie uns doch einfach einen Suchauftrag. Mit unseren weitläufigen Kontakten finden wir bestimmt in kürzester Zeit Ihr persönliches Wunschgerät für Sie. zusätzliche Informationen: An- & Verkauf von Unterhaltungselektronik Abholung gerne möglich – bitte um vorherige telefonische Absprache nachfolgend finden Sie die rechtlichen Informationen, AGB’s, Widerrufsbelehrung sowie Rückgabebelehrung

The Bel Canto C5i is a very well reviewed, nice sounding, compact and attractive 60 watt integrated amplifier. Only one owner (me). I bought it new in 2011 at Stereo Exchange in NYC. Excellent condition. I do not have the original packaging but it includes the manual, remote, and power cord. Located in near Charlottesville, Virginia if you want to pickup locally. Otherwise Ill box it up and you pay shipping.

Bel Canto e.One REF500S Stereo Amplifier in SilverSTORE DEMO / FULL WARRANTYThe REF500S stereo amplifier has incredible power per square inch with two independent mono boards in a single chassis. Independent power supplies and isolated input signal filter technology reduces high power amplifier energy for a cleaner, transparent power.The Bel Canto Impedance Optimized Input Stage is a balanced high Common Mode Rejection, low output impedance driver that is critical to the amplifiers performance, ensuring that the refined dynamic qualities of the recording are preserved. WBT NextGen Speaker Connectors The WBT NextGen connectors provide the best possible connection from the amplifier to the speaker cables. We choose them because they impart minimal sonic signature to the sound, remaining open and grain-free up throughout the audio frequency band.Features:Maximum Power Output: 500W 4 ohms, 250W 8 ohms per channelPower Output 1% THD: 400W 4 ohms, 200W 8 ohms per channelMinimum Load: 2 ohms per channelPeak Output Current: 35 amperes per channelFrequency Response: +/-3 dB 1.5Hz-70KHz, all loadsTHD+N: 0.003% 1W, 1KHz, 4 ohmsIMD (CCIF): 0.0003%, 1W, 14:15KHz, 4 ohmsOutput noise: 35uVRMS A-weighted 10Hz-20KHzVoltage gain: 27dB (single ended or balanced input)Damping factor: >1000Output Impedance at 100Hz:Dynamic Range: 121dBInput Voltage for Max Output: 2VrmsInput connections: Single-ended RCA or balanced XLRRCA input impedance: 100KohmsBalanced input impedance: 200KohmsOutput connections: 2-sets WBT Nextgen 5-way binding postsPower On usage: 19WPower Off usage: 0.0WInternally Set Operating Voltages: 100-120VAC or 230-240VAC 50/60 HzSize: 8.5 x 3.5 x 12[inches], 216 x 88 x 305[mm] (WxHxD)Weight: 15 lbs, 7 Kg Check out all my items on the audiolab-outletBe sure to add me to your favorites list! PLEASE READ OUR POLICIES BELOW Payments:Payments must be made within 3 days of the sale of an item. Failure to pay within 3 days may result in cancellation of the sale OR an unpaid item case opened through eBay. IF YOU HAVE QUESTIONS, PLEASE MESSAGE US BEFORE BIDDING OR PURCHASING AN ITEM. Shipping:Shipping is to the confirmed address and will not be changed after the auction has ended. *** At this time we are NOT processing any shipments internationally or outside of the Lower Contiguous 48 States. AK & HI customers please inquire if you are interested in an item listed. Additional shipping may be required to process your order. We are also unable to ship our items to PO BOXES or APO/FPO addresses unless the item is small. Please inquire if you have any of these types of addresses *** Returns:ALL RETURNS MUST HAVE A RMA# FOR RETURN PROCESSING - Please contact us to obtain an RMA # We will accept items for return with 30 days of sale. Customers wishing to return product for any reasons other than the item being defective will be subject to paying for the cost of return shipping and a restocking fee. IN THE EVENT OF DAMAGE OR THE ITEM NOT AS DESCRIBED:Please contact us directly before opening any case or return request. We want to do everything in our power to offer the best Customer Service possible.