Bang & Olufsen Beocenter 9000/9500 Tuner FM/AM Module 10/17 8002715/8050093 FM, AM, RF, and IF decoder PCB with Tuner module for Beocenter 9000 models other than the 9300. For European/UK market. The tuner module is the single part recommended for replacement rather than repair in the service manual. Removed from a working Beocenter, and kept in warm storage. Postage The part will be carefully packed, boxed, and sent by recorded post. Worldwide postage is available.

Bang & Olufsen Beocenter 9000/9500 Cassette PCB Module 20 8004528D Tape recorder module for Beocenter 9000 series models, excepting the 9300. Please check for differences with the multiple cassette mechanisms used for each model, and note that the service manual likely misprints this module as part number 8004628. Removed from a working Beocenter, and kept in warm storage. Postage The part will be carefully packed, boxed, and sent by recorded post. Worldwide postage is available.

Original Bang & Olufsen tonearm part# 2850068 forBeogram 1100Beogram 1900 (5701)Beogram 3400 (5703, 5726)Beocenter 1800 Complete with counterweight, adjustment slider and cartridge socket.Tested fine.Leads were desoldered (not cut) so are still original lengths. This is a used part in excellent condition.All photos are of the actual part. 1403

Original Bang & Olufsen MMC4 Cartridge/Stylus Uk stock ready for dispatch NOW Sounds great Checked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specification Tracking perfectly with 1.2gram vertical tracking force MMC4 Specifications Description Titanium-bonded elliptical diamond, mounted on a tapered aluminium cantileverTracking force - grams 1.2Diamond Stylus EllipticalCantilever tube. Tap. alum. .Effective tip mass mg 0,4Compliance mg/mN 25Frequency 20-20000 Hz=/-dB 2,5Channel separation 1000>dB 22Output mV/cm/s RMS 0,6Cartridge weight gram 1,6 Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources. No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Original Bang & Olufsen MMC3 Cartridge/StylusUk stock ready for dispatch NOW Sounds greatChecked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1.2gram vertical tracking force MMC3 Product SpecificationsDescription Nude elliptical diamond mounted on a tapered aluminium cantilever Tracking force - grams 1.2Diamond Stylus Elliptical nudeCantilever tube Tap. alum. .Effective tip mass mg 0,35Compliance mg/mN 25Frequency 20-20000 Hz=/-dB 2Channel separation 1000>dB 25Output mV/cm/s RMS 0,6 Cartridge weight gram 1,6 Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridge If you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Original Bang & Olufsen MMC5 Cartridge/StylusUk stock ready for dispatch NOW Sounds greatChecked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1.5gram vertical tracking force Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridge If you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Original Bang & Olufsen MMC2 Cartridge/StylusNewly refurbished Bang & Olufsen MMC2.Works as direct Replacement for with MMC1Refurbished suspension with an original Bang & Olufsen nude multi-radial contact line diamond mounted on a sapphire tube cantilever.Tracking perfectly with 1gram vertical tracking forceMMC2 Specifications :Nude multi-radial Contact Line diamond mounted on a sapphire cantileverTracking force 1 gramNude Contact Line diamond stylusCantilever tube - sapphire Effective tip mass 0.3 mgCompliance mg/mN 30Frequency 20-20000 Hz=/-dB 1.5Channel separation 1000>dB 25Output mV/cm/s RMS 0.6Cartridge weight 1.6 grams Courtesy of Beoworld.orgMMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis.The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker.A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play.While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear.Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies. Any questions just get in touch, Id be glad to help.

Original Bang & Olufsen MMC2 Cartridge/StylusNewly refurbished Bang & Olufsen MMC2.Works as direct Replacement for with MMC1Refurbished suspension with an original Bang & Olufsen nude multi-radial contact line diamond mounted on a sapphire tube cantilever.Tracking perfectly with 1gram vertical tracking forceMMC2 Specifications :Nude multi-radial Contact Line diamond mounted on a sapphire cantileverTracking force 1 gramNude Contact Line diamond stylusCantilever tube - sapphire Effective tip mass 0.3 mgCompliance mg/mN 30Frequency 20-20000 Hz=/-dB 1.5Channel separation 1000>dB 25Output mV/cm/s RMS 0.6Cartridge weight 1.6 grams Courtesy of Beoworld.orgMMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis.The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker.A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play.While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear.Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies. Any questions just get in touch, Id be glad to help.

Fully working, used with possible scratches and normal signs of wear and tearThe part has been removed from the fully working Beocenter. Please check out my video for more details (video taken before it disassembling)Please read the description carefully for what is included in the listing to avoid disappointmentIf you have further questions, please do not hesitate to reach out.

Original Bang & Olufsen MMC4 Cartridge/Stylus Uk stock ready for dispatch NOW Sounds great Checked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specification Tracking perfectly with 1.2gram vertical tracking force MMC4 Specifications Description Titanium-bonded elliptical diamond, mounted on a tapered aluminium cantileverTracking force - grams 1.2Diamond Stylus EllipticalCantilever tube. Tap. alum. .Effective tip mass mg 0,4Compliance mg/mN 25Frequency 20-20000 Hz=/-dB 2,5Channel separation 1000>dB 22Output mV/cm/s RMS 0,6Cartridge weight gram 1,6 Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources. No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Original Bang & Olufsen MMC2 Cartridge/StylusNewly refurbished Bang & Olufsen MMC2.Works as direct Replacement for with MMC1Refurbished suspension with an original Bang & Olufsen nude multi-radial contact line diamond mounted on a sapphire tube cantilever.Tracking perfectly with 1gram vertical tracking forceMMC2 Specifications :Nude multi-radial Contact Line diamond mounted on a sapphire cantileverTracking force 1 gramNude Contact Line diamond stylusCantilever tube - sapphire Effective tip mass 0.3 mgCompliance mg/mN 30Frequency 20-20000 Hz=/-dB 1.5Channel separation 1000>dB 25Output mV/cm/s RMS 0.6Cartridge weight 1.6 grams Courtesy of Beoworld.orgMMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis.The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker.A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play.While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear.Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies. Any questions just get in touch, Id be glad to help.

Original Bang & Olufsen MMC5 Cartridge/StylusUk stock ready for dispatch NOW Sounds greatChecked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1.5gram vertical tracking force Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridge If you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

Original Bang & Olufsen MMC2 Cartridge/StylusNewly refurbished Bang & Olufsen MMC2.Works as direct Replacement for with MMC1Refurbished suspension with an original Bang & Olufsen nude multi-radial contact line diamond mounted on a sapphire tube cantilever.Tracking perfectly with 1gram vertical tracking forceMMC2 Specifications :Nude multi-radial Contact Line diamond mounted on a sapphire cantileverTracking force 1 gramNude Contact Line diamond stylusCantilever tube - sapphire Effective tip mass 0.3 mgCompliance mg/mN 30Frequency 20-20000 Hz=/-dB 1.5Channel separation 1000>dB 25Output mV/cm/s RMS 0.6Cartridge weight 1.6 grams Courtesy of Beoworld.orgMMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis.The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker.A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridgeIf you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play.While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear.Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies. Any questions just get in touch, Id be glad to help.

Original Bang & Olufsen MMC3 Cartridge/StylusUk stock ready for dispatch NOW Sounds greatChecked on a spectrum analyser, delicate, accurate and precise matching perfectly to its published specificationTracking perfectly with 1.2gram vertical tracking force MMC3 Product SpecificationsDescription Nude elliptical diamond mounted on a tapered aluminium cantilever Tracking force - grams 1.2Diamond Stylus Elliptical nudeCantilever tube Tap. alum. .Effective tip mass mg 0,35Compliance mg/mN 25Frequency 20-20000 Hz=/-dB 2Channel separation 1000>dB 25Output mV/cm/s RMS 0,6 Cartridge weight gram 1,6 Courtesy of Beoworld.org MMC stands for Moving Micro-Cross; the patented moving-iron principle upon which all B&O cartridges were based. This unique system employed a cross-shaped armature which, among other advantages, guaranteed exceptional stereo separation since each channel moves on a separate axis. The job of any pickup cartridge is to transform the records physical profile (groove modulation) into corresponding electrical signals (which are then amplified or enlarged by the amplifier and turned into audible sound waves by the loudspeaker. A cartridge must perform three separate and exacting tasks if it is to do this job successfully. It must function mechanically (the movements of the stylus in the groove); it must function magnetically (using the physical movements to create changes in a magnetic field); and it must function electrically (using the changes in magnetic flux to generate an electrical current). At each stage, one type of energy is transferred into another, quite different, type. And the transfer must be perfect, with no energy lost and none added from extraneous sources.No cartridge will ever reach this ideal unless the Laws of Physics can be repealed. However, by understanding the relationships between the three transfer stages and continually applying refined engineering techniques, B&Os belief was that each stage of cartridge improvement would bring each successive cartridge closer to the ideal. Record wear and the cartridge If you take music seriously the value of your record collection is likely to be high. Many of your records are likely to be irreplaceable. You will also know that the signals pressed into your vinyl discs are very fragile indeed. The pickup cartridge can be the discs worse enemy since an ill-suited cartridge can mark a record for life in a single play. While B&O is aware that cartridge specifications are inter-related, their research shows consistently that Effective Tip Mass (ETM) is one of the major factors affecting record wear. ETM is the equivalent of the amount of inertia the groove sees in moving or accelerating the stylus tip. Consequently, the higher the ETM value, the higher the force required for a given constant acceleration. Obviously, more force results in more wear. Three elements contribute to ETM. The stylus tip (diamond) contributes with its entire weight and mass. The armature contributes between 5 - 20% of its weight and mass; the cantilever around 30%. B&O has been able to reduce ETM substantially by refining these elements and building them into an integrated unit. The result is a system which not only reduces damage to the groove walls dramatically, but also provides exceptional performance at all frequencies.

This is the LIGHT grey sliding CD panel for the Bang & Olufsen Beocentre 8500 (not to be confused with the darker grey 8000). The panel is in perfect condition with an unblemished finish.

Fully serviced Bang & Olufsen Beogram 8500 with MMC4 type 5971. One of the last ever turntables produced by Bang and Olufsen Fully serviced with new belts sourced from Beoparts to match same tension as the original specification. Replaced platter belt BS003 Replaced carriage servo belt ref BS023 Regreased carriage servo mechanism. Fully cleaned internally. Cosmetically it is in excellent condition there is barely a mark on it. Barely a mark on it and the matt grey panel looks excellent. The smoke grey translucent dust cover has some minor marks on but these can be polished out. Timeless design by Jacob Jensen. The sound from this turntable is amazing. This was one of the last turntables produced by Bang and Olufsen. The turntable automatically detects the size ofthe record and starts at the correct speed with the 33 or 45 rpm speed lighting up on the tangential arm. The speed can be changed for 12” singles. This turntable is complemented by the Beocenter 8500 not included but will available as a separate listing soon. Please note that within mainland UK I would prefer to arrange delivery myself. The postage costs listed are for someone to drop the item off / meet you somewhere to collect the unit and not for a courier. The postage will help cover fuel costs and can be reviewed with the buyer depending on their location. I am happy to travel 1 or 2 hours to drop it off at a time and date convenient to me which may not be immediately after the sale. I will consider dropping it off at locations further away than 2 hours but may ask the buyer to meet me halfway that way I can cover most of mainland UK. I do travel to the midlands and the south approximately every 2 to 4 weeks. If you are expecting the item within a couple of days of buying then please contact me in advance of purchase to make suitable arrangements. If you are serious about buying the item I am sure we can agree something. Here’s some additional additional information from the Beoworld website… BeoGram 8500 Record Deck Manufactured: 1990 - 1993 Designer: Jacob Jensen Colours: Grey To complement Beocenter 8500, a dedicated record player - Beogram 8500 - was designed specifically for this particular hi-fi centre. The technical aspects of Beogram 8500 were identical to Beogram 9500; it was only the finish that was different which was coloured soft grey to complement the rest of the system. __________________________________ BeoGram 8500 Record Deck Product Specifications Types: 5971 (1990 - Oct 1993) J 5973 (1990 - Dec 1990) Speeds: 33 - 45 rpm Speed deviation: < +/- 0.2 % Wow and flutter, DIN: < +/- 0.06 % Rumble DIN weighted: > 80 dB Rumble DIN unweighted: > 55 dB Power supply: 5971: 220 V 5973: 100 V Power consumption: < 10 W Dimensions W x H x D: 42 x 7.5 x 32.5cm Weight 5.3 kg Link compatibility: Data Link

Bang & Olufsen Beocenter 9000/9500 Cassette PCB Module 20 8004528D Tape recorder module for Beocenter 9000 series models, excepting the 9300. Please check for differences with the multiple cassette mechanisms used for each model, and note that the service manual likely misprints this module as part number 8004628. Removed from a working Beocenter, and kept in warm storage. Postage The part will be carefully packed, boxed, and sent by recorded post. Worldwide postage is available.

Obseclec.com • 07753 241443 • Obscure Eclectics Parts UK delivery and 30-day returns included • worldwide delivery available • before and after sales enquiries: 07753 241443 Beocenter 9000/9500 Rectifier module Part numbers Part number: 8002731 Board number: 8002731G Module number: 62 Compatibility Becenter 9500 and 8500 Also compatible with the Beocenter 9000, but will have a spare socket position for the lack of transceiver Not compatible with Beocenter 9300 Condition The part is in tested, working condition; all four electrolytic capacitors have been replaced in the last 18 months: due to the fit of the original parts extra wires have been added to the negative terminals. Fit is good and, again, the part is working. Postage The part will be carefully packed in an ESD-safe bag, boxed, and sent by recorded post. Postage discounts are available wherever possible if purchasing multiple items. Worldwide courier delivery is available: the price shown applies to Europe only, and delivery further afield may attract a supplement. Enquire before purchase for further details. All items are promptly despatched, and carefully packed using a minimum of plastic packaging. See how we package parts-->

Obseclec.com • 07753 241443 • Obscure Eclectics Parts UK delivery and 30-day returns included • worldwide delivery available • before and after sales enquiries: 07753 241443 Beocenter 9500 & 8500 Input, Power Link, & tone module Part numbers Modules: 53, 54, 68 input select: 8001252 Volume and output amplifier: 8001253 Line in/out: 8001263 Bracket: 2542742 Holder: 3152511 Supply--> Compatibility Beocenter 9500 Beocenter 8500 Condition In tested, fully functioning condition; with new, high-quality electrolytic capacitors in the last 18 months. Postage The part will be carefully packed in an ESD-safe bag, boxed, and sent by recorded post. Postage discounts are available wherever possible if purchasing multiple items. Worldwide courier delivery is available: the price shown applies to Europe only, and delivery further afield may attract a supplement. Enquire before purchase for further details. All items are promptly despatched, and carefully packed using a minimum of plastic packaging. See how we package parts-->

Bang Olufsen beocentre 8500 Plus 8500 beogram, beolab 3000 speakers with brackets and remote. All working apart from the cassette it plays but wont fast forward or rewind. Thanks

This is the LIGHT grey sliding CD panel for the Bang & Olufsen Beocentre 8500 (not to be confused with the darker grey 8000). The panel is in perfect condition with an unblemished finish.

Bang & Olufsen Beocenter, Radio, CD & Tape Cassette, lovely original condition ( was Grandads pride & joy ) can be seen working, with later B & O Beolab 4000 Speakers. collection only.

This is the LIGHT grey sliding CD panel for the Bang & Olufsen Beocentre 8500 (not to be confused with the darker grey 8000). The panel is in perfect condition with an unblemished finish.

Genuine vintage Bang & Olufsen Beocenter 8000 stereo radio cassette CD deck MOSTLY WORKING BUT REQUIRING SOME REPAIRS so selling as spares and repairs. Everything lights up on the touch panels and all functions respond. The radio works, changes frequency, searches and finds stations. The glass touch panels are undamaged but loose and will need new sticky tape, all cheaply available and plenty of you tube videos on what is an easy procedure. The CD and tape doors open and shut CD starts then stops without playing. Tape sounds drunk! Grey centre panels in good condition, CD has slight wear. Not an exhaustive list and not to be relied upon, sold as spares or repairs so absolutely no returns under any circumstances. Very heavy as is usual for B&O hence shipping cost. Feel free to collect from HorshamSelling as spares or repairs so no returns. See Beowold review below.Shipping or collection from Horsham, West SussexPlease see my other B&O listingsThanks for looking! PS Please dont send me your contact details as this is detected by ebay and may result in restrictions being imposed on either or both of us. Thanks for your understanding Please note! Shipping to non-mainland Britain may attract a surcharge. Please ask for a quote BeoCenter 8500 Manufactured: 1989 - 1992 Designer: Jacob Jensen Colours: GreySimple logical operationA light touch directly was all you needed to access its operation. The illuminated display led you logically through the programming and other functions always showing you what to do next. This ease and simplicity of use was the first impression you obtained of the music system. And equally easy to use was the optional remote control terminal.Entertainment and information from three reliable sourcesYou could preset up to 20 FM and AM stations on the receiver. And when you made your choice, search and fine tuning were completely automatic. The CD player which accommodated both 12cm and 8cm compact discs was also ready for your commands. It gave you instant access to a specific track anywhere on the disc and allowed you to change the order in which the tracks were played, or to simply choose only those tracks you wished to listen to. Technology at its most convenient best. The fine art of control of Beocenter 8500 The unfailing sensi-touch control of the works through a condenser effect. A graphite area is printed on the underside of the glass panel, and charged with a high frequency current. Even the lightest touch of a finger will spark the reaction.Beocenter 8500For individuals who could live without time-programming but wanted the advanced features of the 9500, Bang & Olufsen created the Beocenter 8500. There was no difference in the quality of the sound, but the cabinet was finished in a soft grey as an alternative to the polished aluminium finish of the 9500 BeoCenter 8500 Product SpecificationsTypes: EU 2506 (1989 - Feb 1994) GB 2507 (1989 - Dec 1993) AUS 2510 (1989 - Dec 1993) J 2509 (1989 - Dec 1993) US 2508 (1989 - Dec 1993) Amplifier: Long-term max. output power: IEC 2 x 80 watts / 8 ohms Total harmonic distortion IHF: < 0.1 % & 30 watts 20 - 20,000 Hz Dynamic headroom 1 dB: / 8 ohms Intermodulation IHF: < 0.1 % Bass control at 40 Hz: +/- 10 dB Treble control at 12,500 Hz: +/- 8 dB Tape recorder: Compact cassette C46 - C120 Recording system HX PRO Tape head Sendust Wow and flutter DIN < 0.15 % Frequency range chrome 30 - 18,000 Hz +/- 3 dB Signal-to-noise ratio CCIR/ARM Metal Dolby NR B:>64 dB, C: >73 dB Chrome Dolby NR B:>65 dB, C: >74 dB Ferro Dolby NR B:>63 dB, C: >72 dB Power supply: 110 - 130 - 220 - 240 voltage switch Power consumption Max. 200 W Dimensions W x H x D 76 x 11 x 34cm Weight 14 kg Tuner: FM range: 76 - 90 MHz (Type 2509, 2513) 87.5 - 108 MHz (Type 2506, 2508, 2510, 2511, 2512, 2514) LW range 2506, 2511: 150 - 350 kHz MW range 2506, 2508, 2509, 2510, 2511, 2512, 2513, 2514520 - 610 kHz Compact disc player: Frequency range 3 - 20,000 Hz +/- 0.3 dB Signal-to-noise ratio > 100 dB / 110 dB A-weighted Dynamic range > 96 dB Harmonic distortion 0.0025 % at 0 dB 0.0025 % at -20 dB Channel separation > 101 dB Converter system 2 x 16 bit, 4 x oversampling Low pass filter analogue Bessel Connections: Beocord Tape 1 Built-in Beocord Tape 2 7-pin DIN, Datalink Beogram CD Built-in Beogram LP 7-pin DIN, Datalink BeoLab 2 x Power Link Beovox 4-pin DIN Beovision 7-pin DIN, Datalink On 27-May-23 at 16:15:58 BST, seller added the following information: Lower glass isnt broken as such, if you look closely at the 3rd photo theres a chip at the bottom right