Description
AudioQuest 1m Victoria 5 Pin DIN - 2-Male RCA Stereo Analogue Audio Interconnect This listing is for an AudioQuest 1m Victoria 5 Pin DIN - 2-Male RCA Stereo Analogue Audio Interconnect, which is in excellent used condition and perfect working order. the cost new was £299 What AudioQuest say: ?Analog-Audio Interconnect Cable named after the Victoria Falls Bridge, a thrilling drop of 111 metres (364 ft) in front of spectacular Victoria Falls. In all Bridges & Falls, you’ll find better metals and more sophisticated technologies — including Air-Tube insulation, Dielectric-Bias System, and Noise-Dissipation System Note: All cables in our Bridges & Falls Series place their left and right channels in a single jacket, and feature our Asymmetrical Double-Balanced geometry with separate high-quality positive and negative conductors. This design allows for a thin, flexible, and uniquely versatile high-performance cable that can be terminated with a variety of today’s connections, including 3.5mm (male or female), DIN, and RCA. Do keep in mind, however, that, by necessity, the plugs on Bridges & Falls cables are fairly close together. Solid Perfect-Surface Copper+ (PSC+) Conductors Solid conductors prevent both electrical and magnetic interaction strand-to-strand interaction, major sources of distortion. Surface quality is critical because a conductor can be considered as a rail-guide for both the fields within a conductor, and for the magnetic fields that extend outside the conductor. The astonishingly smooth and pure surface of all AudioQuests’s Perfect-Surface metals nearly eliminates harshness and greatly increases clarity compared to lesser materials. Extremely high-purity Perfect-Surface Copper+ further minimizes distortion caused by grain boundaries, which exist within any metal conductor, nearly eliminating harshness and greatly increasing clarity compared to OFHC, OCC, 8N and other coppers. Asymmetrical Double-Balanced Geometry Purpose designed for single-ended applications, Asymmetrical Double-Balanced Geometry offers a relatively lower impedance on the ground for a richer, and more dynamic experience. While many single-ended cable designs use a single path for both the ground and the shield, Double-Balanced designs separate the two for cleaner, quieter performance. Polyethylene Air-Tube Insulation Any solid material adjacent to a conductor is actually part of an imperfect circuit. Wire insulation and circuit board materials all absorb energy. Some of this energy is stored and then released as distortion. AudioQuest, however, uses Polyethylene Air-Tube Insulation on both conductors, for increased geometry stabilization and improved clarity. Because air absorbs next to no energy and Polyethylene is low-loss and has a benign distortion profile, Polyethylene Air-Tube Insulation, with its high air content, causes much less of the out-of-focus effect common to other materials. Dielectric-Bias System with Radio Frequency Trap All insulation between two or more conductors is also a dielectric whose properties will affect the integrity of the signal. When the dielectric is unbiased, dielectric-involvement (absorption and non-linear release of energy) causes different amounts of time delay (phase shift) for different frequencies and energy levels, which is a real problem for very time-sensitive multi-octave audio. The inclusion of an RF Trap (developed for AudioQuest’s Niagara Series of power products), ensures that radio-frequency noise will not be induced into the signal conductors from the DBS field elements. (DBS, US Pat #s 7,126,055 & 7,872,195 B1) Carbon-Based 3-Layer Noise-Dissipation System (NDS) Its easy to accomplish 100% shield coverage. Preventing captured Radio Frequency Interference (RFI) from modulating the equipments ground reference requires AQs Noise-Dissipation System (NDS). Traditional shield systems typically absorb and then drain noise/RF energy to component ground, modulating and distorting the critical reference ground plane, which in turn causes a distortion of the signal. NDSs alternating layers of metal and carbon-loaded synthetics shield the shield, absorbing and reflecting most of this noise/RF energy before it reaches the layer attached to ground. Cold-Welded, Direct-Silver Plated Pure Purple Copper Terminations Cold-Welded, Direct-Silver Plated Pure Purple Copper Terminations. Direct-Silver Plating is optimized for sound. It looks dull because there is no underlying layer of shiny, distortion-causing nickel. TERMS Place a bid only if youre serious about buying the item. I ask that payment is made immediately upon purchase, and prefer payment by PayPal. If you pay by PayPal I will ONLY post the item to a PayPal confirmed address. All goods purchased are securely and safely packaged for transit. The cost of Packaging materials (e.g. Jiffy Bags, Bubble Wrap etc) is included in the P&P charge. Items will normally be sent within 3 working days of receipt of cleared payment. I only deliver to addresses in Great Britain or Northern Ireland that are recognised by the Royal Mail. I will not be responsible for the performance of the carrier, insurance is advised and we will provide costs for this upon request (if paying insurance please check the item before signing with courier). I always reciprocate feedback. Please contact me through the eBay system if there is a problem.
| 
Live search