ATTENTION! This auction is for AUDIO RESEARCH PREAMPLIFIER SP 14 ONLY!!!!! If you want to by extra AUDIO RESEARCH CLASSIC 60 - See My other auctions. The SP14s musicality comes surprisingly close to the state of the art, with soundstage of remarkable depth and breadth; imaging of uncanny solidity: palpable dynamic authority; timbral accuracy that virtually recreates live music; an exceptionally low noise floor; and a special ease with frequency extremes. But unlike many high-performance preamplifiers, the SP14 doesnt scrimp on control features. It has separate Gain and Attenuation for wide-ranging-yet-subtle level management. Separate Input and Record Output selectors (with a common menu) permit exceptional flexibility in playing and recording: owners can listen to one source while recording from another. The Bypass switch allows owners to remove the Balance and Mode controls from the signal path, for greater sonic purity. There are two separate sets of outputs, and three power outlets. And, of course, the SP14 features its own version of the hybrid technology that has made Audio Research electronics world-famous. As with every Audio Research product, SP14 parts quality, construction and factory support are the finest in the audio industry, with a two-decade track record to prove it. And all this comes at only half the cost of the celebrated SP15. FREQUENCY RESPONSEHigh-level section: ±.5dB, 5Hz to 50kHz, -3db points below 1Hz and above 200 kHz. Magnetic phono: ±.3dB of RIAA, 30Hz to 40kHzDISTORTION (THD)Less than .01% at 2V RMS outputNOISE & HUMHigh level: (1) 70 µV RMS maximum residual unweighted wideband noise at main output with gain control minimum (98 dB below 5V RMS output) (2) More than 100dB below 1V RMS input (less than 7 µV equivalent input noise). Phono: 0.12 µV equivalent input noise, IHF weighted, shorted input (78dB below 1mV input).GAINPhono input to tape output: 46 dB. Phono input to main output: 66 dB. High-level inputs to tape output: 0 dB. High-level inputs to main output: 20 dB.INPUT IMPEDANCELine inputs: 50 K ohms. Phono: 47K ohms (provisions for any value below 47K ohms or added input capacitance for matching certain magnetic cartridges.)OUTPUT IMPEDANCE250 ohms main output, 1000 ohms recorder output. Recommended load 60K - 100K ohms and 100pF. (20K ohms minimum and 1000pF maximum)OUTPUT POLARITY-MAXIMUM INPUTSMagnetic phono, 200mV at 1kHz (1000mV RMS, 10 kHz). High-level inputs are essentially overload-proof.RATED OUTPUTS2V RMS 5 Hz to 50 kHz, all outputs; 60K ohm load (main output capability is 50V RMS output at .5% THD at 1kHz into a 100K ohm load with 5V RMS high level input)POWER SUPPLIESElectronically-regulated low and high voltage supplies and electronic decoupling. Shielded toroid transformer. Line regulation is better than .01%.TUBE COMPLEMENT(1) 6DJ8/ECC88POWER REQUIREMENTS100-135VAC 60Hz (200-270VAC 50/60Hz) 60 WattsOTHERHybrid FET/Tube audio circuit, solid-state power supply. Inputs (7): Phono, C-D, Tuner, Video, Spare, Tape 1, Tape 2. Outputs (4): (2) Main, (2) Recorder. Controls (6): Gain, Attenuation, Balance. Mode, Record Out, Input. Switches (8): Power, Outlets, Bypass, Mute, Copy, Tape 1 to 2/2 to 1, Tape 2/1, Monitor.DIMENSIONS19” (48 cm) W x 5 ¼” (13.4 cm) H (standard rack panel) x 10 ¼” (26 cm) D. Handles extend 1 ? (4.1 cm) forward of front panel. Rear chassis fittings extend ? (2.3 cm)WEIGHT12 lbs. (5.5kg) Net, 21 lbs. (9.6 kg) Shipping

audio research sp 16 all tube preamp in good working and cosmetic condion. complete with all the factory box and packaging, manual power cord remote and extra tubes. please examine all the photos for its part of the description. no refunds or returns. no international shipping. thanks for looking. note: the tubes are installed in the preamp. for the winning bidder make sure to check all the tubes if its installed properly to the socket before plugging it in, it might fall out during shipping. and the lock of the remotes battery cover is broken but works properly, just need to tape it. the spare tubes are included when i bought these amp but i havent tried to install it. please dont hesitate to message me for any questions you might have. thank you…

ATTENTION! This auction is for AUDIO RESEARCH PREAMPLIFIER SP 14 ONLY!!!!! See My other auctions. The SP14s musicality comes surprisingly close to the state of the art, with soundstage of remarkable depth and breadth; imaging of uncanny solidity: palpable dynamic authority; timbral accuracy that virtually recreates live music; an exceptionally low noise floor; and a special ease with frequency extremes. But unlike many high-performance preamplifiers, the SP14 doesnt scrimp on control features. It has separate Gain and Attenuation for wide-ranging-yet-subtle level management. Separate Input and Record Output selectors (with a common menu) permit exceptional flexibility in playing and recording: owners can listen to one source while recording from another. The Bypass switch allows owners to remove the Balance and Mode controls from the signal path, for greater sonic purity. There are two separate sets of outputs, and three power outlets. And, of course, the SP14 features its own version of the hybrid technology that has made Audio Research electronics world-famous. As with every Audio Research product, SP14 parts quality, construction and factory support are the finest in the audio industry, with a two-decade track record to prove it. And all this comes at only half the cost of the celebrated SP15. FREQUENCY RESPONSEHigh-level section: ±.5dB, 5Hz to 50kHz, -3db points below 1Hz and above 200 kHz. Magnetic phono: ±.3dB of RIAA, 30Hz to 40kHzDISTORTION (THD)Less than .01% at 2V RMS outputNOISE & HUMHigh level: (1) 70 µV RMS maximum residual unweighted wideband noise at main output with gain control minimum (98 dB below 5V RMS output) (2) More than 100dB below 1V RMS input (less than 7 µV equivalent input noise). Phono: 0.12 µV equivalent input noise, IHF weighted, shorted input (78dB below 1mV input).GAINPhono input to tape output: 46 dB. Phono input to main output: 66 dB. High-level inputs to tape output: 0 dB. High-level inputs to main output: 20 dB.INPUT IMPEDANCELine inputs: 50 K ohms. Phono: 47K ohms (provisions for any value below 47K ohms or added input capacitance for matching certain magnetic cartridges.)OUTPUT IMPEDANCE250 ohms main output, 1000 ohms recorder output. Recommended load 60K - 100K ohms and 100pF. (20K ohms minimum and 1000pF maximum)OUTPUT POLARITY-MAXIMUM INPUTSMagnetic phono, 200mV at 1kHz (1000mV RMS, 10 kHz). High-level inputs are essentially overload-proof.RATED OUTPUTS2V RMS 5 Hz to 50 kHz, all outputs; 60K ohm load (main output capability is 50V RMS output at .5% THD at 1kHz into a 100K ohm load with 5V RMS high level input)POWER SUPPLIESElectronically-regulated low and high voltage supplies and electronic decoupling. Shielded toroid transformer. Line regulation is better than .01%.TUBE COMPLEMENT(1) 6DJ8/ECC88POWER REQUIREMENTS100-135VAC 60Hz (200-270VAC 50/60Hz) 60 WattsOTHERHybrid FET/Tube audio circuit, solid-state power supply. Inputs (7): Phono, C-D, Tuner, Video, Spare, Tape 1, Tape 2. Outputs (4): (2) Main, (2) Recorder. Controls (6): Gain, Attenuation, Balance. Mode, Record Out, Input. Switches (8): Power, Outlets, Bypass, Mute, Copy, Tape 1 to 2/2 to 1, Tape 2/1, Monitor.DIMENSIONS19” (48 cm) W x 5 ¼” (13.4 cm) H (standard rack panel) x 10 ¼” (26 cm) D. Handles extend 1 ? (4.1 cm) forward of front panel. Rear chassis fittings extend ? (2.3 cm)WEIGHT12 lbs. (5.5kg) Net, 21 lbs. (9.6 kg) Shipping

ATTENTION! This auction is for AUDIO RESEARCH AMPLIFIER CLASSIC 60 ONLY!!!!! See My other auctions.The new Classic 60 Hybrid Stereo Power Amplifier resembles the long-popular D115 in Audio Researchs family of High Definition® power amplifiers. But its lineage is strictly Classic 150. Which means nothing less than state-of-the-art in design, construction, musicality, and operational convenience...at an affordable price. Like the Classic 150, the Classic 60 proceeds from the notion that power ratings dont always describe a power amplifiers real capabilities. Far more important are such qualities as dynamic stability. lucidity, subtlety. And to achieve those, Audio Research has used its traditional partial cathode coupling along with triode operation of the Classic 60s eight 6550 power output tubes. Additional circuit improvements, as well as the usual rigorous parts selection and manufacturing Audio Research, are noted for, also contributing sonically. Translated into the language of listening, this signifies stunning bandwidth, a noise floor virtually beneath audibility, and musically fulfilling SPLs at dramatically lower gain settings. Dynamics, timbres of individual instruments, soundstage, and musical emotion all surge out from a black velvet of silence. Simply put the Classic 60 resolves far more of a musical program than amplifiers rated at two, three, or four times its seemingly modest 60 WPC. But the Classic 60 is easily up to the task of driving all but the most demanding loudspeakers, even in spacious listening rooms. And while it shows modest preamplifiers in their best light, it also shines when coupled with premiere designs, such as Audio Researchs SP14 or SP15. Convenience figures are high on the Classic 60s list of attributes, as well. For example, the DC balance of the output tubes is maintained automatically, while tube biasing continuously adjusts to changes in incoming line voltage. Performance stays razor-sharp without bothersome tweaking or adjustments. And quiet fan cooling, along with triode operation, means significantly longer tube life. A Classic 60 owner can look forward to years of low-maintenance performance POWER OUTPUT60 watts minimum continuous at 16 ohms from 15Hz to 20kHz with less than 1.0% total harmonic distortion. Typically below .005% at 1 watt. The approximate actual power available at clipping: 62 watts. (1kHz) (Note that the actual RMS power output is dependent upon both line voltage and condition ie: if the power line has high distortion, maximum power will be affected adversely, although, from a listening standpoint, this is not very critical.)POWER BANDWIDTH(-3dB points): 12Hz to 40kHzFREQUENCY RESPONSE-INPUT SENSITIVITY.55V RMS for rated outputINPUT IMPEDANCE100K ohms, nominalOUTPUT TAPS-OUTPUT REGULATIONApproximately 0.3dB 16-ohm load to open circuitOVERALL NEGATIVE FEEDBACK20dBDAMPING FACTORApproximately 30DISTORTION-SLEW RATE20V/µsRISE TIME2.0 µsHUM & NOISELess than 2.0mV RMS - 84dB below-rated output (20kHz bandwidth unweighted, inputs shorted)POWER SUPPLY ENERGY STORAGEApproximately 280 joulesPOWER REQUIREMENTS105-125VAC 60Hz (210-250VAC 50Hz) 500 watts at rated output, 700 watts maximum, 370 watts at idleTUBE COMPLEMENT(4 matched pairs) 6550 power output, (4) 6FQ7/6CG7 driversDIMENSIONS19 (48 cm) W (standard rack panel) x 7 (18 cm) H x 15 ¾ (40 cm) D (front panel back). Handles extend 1 ? (4.1 cm) forward of the front panel. Output connectors extend 1 behind the rear panel.WEIGHT63 lbs (28.64 kg) Net, 76 lbs (34.55 kg) Shipping

Audio Research ARC SP-16 Tube preamplifier W Remote. I purchased this tube preamplifier about two months ago, and it was only used for a few hours in my system. This preamplifier does have a tube phono section as well as a tube line level section. The tubes in the photo section are the stock electro harmonix 12ax7’s. I did swap the tubes in the line level section to some used NOS,RCA Tubes. Two of those tubes are 12ax7’s and one is a 5751. I would describe the sound as extremely clean and pristine. But I wouldn’t describe the sound is overly tube like. I would rate the condition at a 7/10. A few minor scratches is all. No returns and shipping to the US continental only!

Audio Research SP16 Pre-amplifier Tube / Valve Pre-amp with Phono Stage New Valves fitted. Serviced in June 2023.Perfect working order. Excellent cosmetic condition with hardly any marks(remote is not included) PaymenteBay, Bank Transfer, or Cash on Collection Shipping Prices (includes the cost of Full Insurance) Collection from Bristol BS7 - FreeUK Mainland from £19.90Worldwide from £29.90 It will be well packed and Fully Insured. Please Note: A signature is required on delivery Non UK Customers - Important InformationVAT, Customs Duty, or other Tax may be payable if you are buying from outside of the UK. Please check. It is the buyers responsibility to pay these charges. The full sale value of the goods will be declared on Customs Form *Returns*Returns are ONLY accepted if the item is faulty or not as describedItems are checked, photographed, and security marked before shippingI am confident you will find the listing is accurate Thank you for looking

Audio Research SP-12 Röhren Vorverstärker mit ECC88/6DJ8. Volle Funktion, optisch nicht mehr top.War vor 2 Jahren im Service und es wurde ein Kondensator im Netzteil getauscht.

Audio Research ARC SP-16 Tube preamplifier W Remote. I purchased this tube preamplifier about two months ago, and it was only used for a few hours in my system. This preamplifier does have a tube phono section as well as a tube line level section. The tubes in the photo section are the stock electro harmonix 12ax7’s. I did swap the tubes in the line level section to some used NOS,RCA Tubes. Two of those tubes are 12ax7’s and one is a 5751. I would describe the sound as extremely clean and pristine. But I wouldn’t describe the sound is overly tube like. I would rate the condition at a 7/10. A few minor scratches is all. No returns and shipping to the US continental only!