The Classic 60 Hybrid Stereo Power Amplifier resembles the long-popular D115 in Audio Researchs family of High Definition® power amplifiers. But its lineage is strictly Classic 150. Which means nothing less than state-of-the-art in design, construction, musicality, and operational convenience...at an affordable price. Like the Classic 150, the Classic 60 proceeds from the notion that power ratings dont always describe a power amplifiers real capabilities. Far more important are such qualities as dynamic stability. lucidity, subtlety. And to achieve those, Audio Research has used its traditional partial cathode coupling along with triode operation of the Classic 60s eight 6550 power output tubes. Additional circuit improvements, as well as the usual rigorous parts selection and manufacturing Audio Research, are noted for, also contributing sonically. Translated into the language of listening, this signifies stunning bandwidth, a noise floor virtually beneath audibility, and musically fulfilling SPLs at dramatically lower gain settings. Dynamics, timbres of individual instruments, soundstage, and musical emotion all surge out from a black velvet of silence. Simply put the Classic 60 resolves far more of a musical program than amplifiers rated at two, three, or four times its seemingly modest 60 WPC. But the Classic 60 is easily up to the task of driving all but the most demanding loudspeakers, even in spacious listening rooms. And while it shows modest preamplifiers in their best light, it also shines when coupled with premiere designs, such as Audio Researchs SP14 or SP15. Convenience figures are high on the Classic 60s list of attributes, as well. For example, the DC balance of the output tubes is maintained automatically, while tube biasing continuously adjusts to changes in incoming line voltage. Performance stays razor-sharp without bothersome tweaking or adjustments. And quiet fan cooling, along with triode operation, means significantly longer tube life. A Classic 60 owner can look forward to years of low-maintenance performance POWER OUTPUT60 watts minimum continuous at 16 ohms from 15Hz to 20kHz with less than 1.0% total harmonic distortion. Typically below .005% at 1 watt. The approximate actual power available at clipping: 62 watts. (1kHz) (Note that the actual RMS power output is dependent upon both line voltage and condition ie: if the power line has high distortion, maximum power will be affected adversely, although, from a listening standpoint, this is not very critical.)POWER BANDWIDTH(-3dB points): 12Hz to 40kHzFREQUENCY RESPONSE-INPUT SENSITIVITY.55V RMS for rated outputINPUT IMPEDANCE100K ohms, nominalOUTPUT TAPS-OUTPUT REGULATIONApproximately 0.3dB 16-ohm load to open circuitOVERALL NEGATIVE FEEDBACK20dBDAMPING FACTORApproximately 30DISTORTION-SLEW RATE20V/µsRISE TIME2.0 µsHUM & NOISELess than 2.0mV RMS - 84dB below-rated output (20kHz bandwidth unweighted, inputs shorted)POWER SUPPLY ENERGY STORAGEApproximately 280 joulesPOWER REQUIREMENTS105-125VAC 60Hz (210-250VAC 50Hz) 500 watts at rated output, 700 watts maximum, 370 watts at idleTUBE COMPLEMENT(4 matched pairs) 6550 power output, (4) 6FQ7/6CG7 driversDIMENSIONS19 (48 cm) W (standard rack panel) x 7 (18 cm) H x 15 ¾ (40 cm) D (front panel back). Handles extend 1 ? (4.1 cm) forward of the front panel. Output connectors extend 1 behind the rear panel.WEIGHT63 lbs (28.64 kg) Net, 76 lbs (34.55 kg) Shipping

This 3 ft RCA Audio/Video Cable is perfect for connecting your Acoustic Research AP060 to your TV or other audio and video equipment. The gold plated connectors ensure a clear and reliable signal, while the 1:6 connection split/duplication allows you to share your audio and video with multiple devices. With its durable construction and compatibility with a variety of models, this cable is a must-have for any audio and video setup. Whether youre watching your favorite shows or listening to music, this RCA cable delivers superior performance without mentioning its specific condition. This will ship to you in a box, not a cheapie plastic outer bag, so the condition that you see now is how you will get it later.

The Classic 60 Hybrid Stereo Power Amplifier resembles the long-popular D115 in Audio Researchs family of High Definition® power amplifiers. But its lineage is strictly Classic 150. Which means nothing less than state-of-the-art in design, construction, musicality, and operational convenience...at an affordable price. Like the Classic 150, the Classic 60 proceeds from the notion that power ratings dont always describe a power amplifiers real capabilities. Far more important are such qualities as dynamic stability. lucidity, subtlety. And to achieve those, Audio Research has used its traditional partial cathode coupling along with triode operation of the Classic 60s eight 6550 power output tubes. Additional circuit improvements, as well as the usual rigorous parts selection and manufacturing Audio Research, are noted for, also contributing sonically. Translated into the language of listening, this signifies stunning bandwidth, a noise floor virtually beneath audibility, and musically fulfilling SPLs at dramatically lower gain settings. Dynamics, timbres of individual instruments, soundstage, and musical emotion all surge out from a black velvet of silence. Simply put the Classic 60 resolves far more of a musical program than amplifiers rated at two, three, or four times its seemingly modest 60 WPC. But the Classic 60 is easily up to the task of driving all but the most demanding loudspeakers, even in spacious listening rooms. And while it shows modest preamplifiers in their best light, it also shines when coupled with premiere designs, such as Audio Researchs SP14 or SP15. Convenience figures are high on the Classic 60s list of attributes, as well. For example, the DC balance of the output tubes is maintained automatically, while tube biasing continuously adjusts to changes in incoming line voltage. Performance stays razor-sharp without bothersome tweaking or adjustments. And quiet fan cooling, along with triode operation, means significantly longer tube life. A Classic 60 owner can look forward to years of low-maintenance performance POWER OUTPUT60 watts minimum continuous at 16 ohms from 15Hz to 20kHz with less than 1.0% total harmonic distortion. Typically below .005% at 1 watt. The approximate actual power available at clipping: 62 watts. (1kHz) (Note that the actual RMS power output is dependent upon both line voltage and condition ie: if the power line has high distortion, maximum power will be affected adversely, although, from a listening standpoint, this is not very critical.)POWER BANDWIDTH(-3dB points): 12Hz to 40kHzFREQUENCY RESPONSE-INPUT SENSITIVITY.55V RMS for rated outputINPUT IMPEDANCE100K ohms, nominalOUTPUT TAPS-OUTPUT REGULATIONApproximately 0.3dB 16-ohm load to open circuitOVERALL NEGATIVE FEEDBACK20dBDAMPING FACTORApproximately 30DISTORTION-SLEW RATE20V/µsRISE TIME2.0 µsHUM & NOISELess than 2.0mV RMS - 84dB below-rated output (20kHz bandwidth unweighted, inputs shorted)POWER SUPPLY ENERGY STORAGEApproximately 280 joulesPOWER REQUIREMENTS105-125VAC 60Hz (210-250VAC 50Hz) 500 watts at rated output, 700 watts maximum, 370 watts at idleTUBE COMPLEMENT(4 matched pairs) 6550 power output, (4) 6FQ7/6CG7 driversDIMENSIONS19 (48 cm) W (standard rack panel) x 7 (18 cm) H x 15 ¾ (40 cm) D (front panel back). Handles extend 1 ? (4.1 cm) forward of the front panel. Output connectors extend 1 behind the rear panel.WEIGHT63 lbs (28.64 kg) Net, 76 lbs (34.55 kg) Shipping

This 3 ft RCA Audio/Video Cable is perfect for connecting your Acoustic Research AP060 to your TV or other audio and video equipment. The gold plated connectors ensure a clear and reliable signal, while the 1:6 connection split/duplication allows you to share your audio and video with multiple devices. With its durable construction and compatibility with a variety of models, this cable is a must-have for any audio and video setup. Whether youre watching your favorite shows or listening to music, this RCA cable delivers superior performance without mentioning its specific condition. This will ship to you in a box, not a cheapie plastic outer bag, so the condition that you see now is how you will get it later.

The Classic 60 Hybrid Stereo Power Amplifier resembles the long-popular D115 in Audio Researchs family of High Definition® power amplifiers. But its lineage is strictly Classic 150. Which means nothing less than state-of-the-art in design, construction, musicality, and operational convenience...at an affordable price. Like the Classic 150, the Classic 60 proceeds from the notion that power ratings dont always describe a power amplifiers real capabilities. Far more important are such qualities as dynamic stability. lucidity, subtlety. And to achieve those, Audio Research has used its traditional partial cathode coupling along with triode operation of the Classic 60s eight 6550 power output tubes. Additional circuit improvements, as well as the usual rigorous parts selection and manufacturing Audio Research, are noted for, also contributing sonically. Translated into the language of listening, this signifies stunning bandwidth, a noise floor virtually beneath audibility, and musically fulfilling SPLs at dramatically lower gain settings. Dynamics, timbres of individual instruments, soundstage, and musical emotion all surge out from a black velvet of silence. Simply put the Classic 60 resolves far more of a musical program than amplifiers rated at two, three, or four times its seemingly modest 60 WPC. But the Classic 60 is easily up to the task of driving all but the most demanding loudspeakers, even in spacious listening rooms. And while it shows modest preamplifiers in their best light, it also shines when coupled with premiere designs, such as Audio Researchs SP14 or SP15. Convenience figures are high on the Classic 60s list of attributes, as well. For example, the DC balance of the output tubes is maintained automatically, while tube biasing continuously adjusts to changes in incoming line voltage. Performance stays razor-sharp without bothersome tweaking or adjustments. And quiet fan cooling, along with triode operation, means significantly longer tube life. A Classic 60 owner can look forward to years of low-maintenance performance POWER OUTPUT60 watts minimum continuous at 16 ohms from 15Hz to 20kHz with less than 1.0% total harmonic distortion. Typically below .005% at 1 watt. The approximate actual power available at clipping: 62 watts. (1kHz) (Note that the actual RMS power output is dependent upon both line voltage and condition ie: if the power line has high distortion, maximum power will be affected adversely, although, from a listening standpoint, this is not very critical.)POWER BANDWIDTH(-3dB points): 12Hz to 40kHzFREQUENCY RESPONSE-INPUT SENSITIVITY.55V RMS for rated outputINPUT IMPEDANCE100K ohms, nominalOUTPUT TAPS-OUTPUT REGULATIONApproximately 0.3dB 16-ohm load to open circuitOVERALL NEGATIVE FEEDBACK20dBDAMPING FACTORApproximately 30DISTORTION-SLEW RATE20V/µsRISE TIME2.0 µsHUM & NOISELess than 2.0mV RMS - 84dB below-rated output (20kHz bandwidth unweighted, inputs shorted)POWER SUPPLY ENERGY STORAGEApproximately 280 joulesPOWER REQUIREMENTS105-125VAC 60Hz (210-250VAC 50Hz) 500 watts at rated output, 700 watts maximum, 370 watts at idleTUBE COMPLEMENT(4 matched pairs) 6550 power output, (4) 6FQ7/6CG7 driversDIMENSIONS19 (48 cm) W (standard rack panel) x 7 (18 cm) H x 15 ¾ (40 cm) D (front panel back). Handles extend 1 ? (4.1 cm) forward of the front panel. Output connectors extend 1 behind the rear panel.WEIGHT63 lbs (28.64 kg) Net, 76 lbs (34.55 kg) Shipping

4K/60Hz HDMI Scaler with Audio Embed/Extract & Image Flip Capability Any video resolution can be scaled up or down to any other resolutionSupports UHD / 4K @ 60 Hz with 4:4:4 Color on input and outputHorizontal and Vertical mirroring (x or y-axis flip)Analog and digital audio inputs and outputsAdvanced scaling for real-time frame rate capture & conversionBy default scales the output to the native resolution of any connected display for more info: https://halltechav.com/product/sc-hd-2b/

The Classic 60 Hybrid Stereo Power Amplifier resembles the long-popular D115 in Audio Researchs family of High Definition® power amplifiers. But its lineage is strictly Classic 150. Which means nothing less than state-of-the-art in design, construction, musicality, and operational convenience...at an affordable price. Like the Classic 150, the Classic 60 proceeds from the notion that power ratings dont always describe a power amplifiers real capabilities. Far more important are such qualities as dynamic stability. lucidity, subtlety. And to achieve those, Audio Research has used its traditional partial cathode coupling along with triode operation of the Classic 60s eight 6550 power output tubes. Additional circuit improvements, as well as the usual rigorous parts selection and manufacturing Audio Research, are noted for, also contributing sonically. Translated into the language of listening, this signifies stunning bandwidth, a noise floor virtually beneath audibility, and musically fulfilling SPLs at dramatically lower gain settings. Dynamics, timbres of individual instruments, soundstage, and musical emotion all surge out from a black velvet of silence. Simply put the Classic 60 resolves far more of a musical program than amplifiers rated at two, three, or four times its seemingly modest 60 WPC. But the Classic 60 is easily up to the task of driving all but the most demanding loudspeakers, even in spacious listening rooms. And while it shows modest preamplifiers in their best light, it also shines when coupled with premiere designs, such as Audio Researchs SP14 or SP15. Convenience figures are high on the Classic 60s list of attributes, as well. For example, the DC balance of the output tubes is maintained automatically, while tube biasing continuously adjusts to changes in incoming line voltage. Performance stays razor-sharp without bothersome tweaking or adjustments. And quiet fan cooling, along with triode operation, means significantly longer tube life. A Classic 60 owner can look forward to years of low-maintenance performance POWER OUTPUT60 watts minimum continuous at 16 ohms from 15Hz to 20kHz with less than 1.0% total harmonic distortion. Typically below .005% at 1 watt. The approximate actual power available at clipping: 62 watts. (1kHz) (Note that the actual RMS power output is dependent upon both line voltage and condition ie: if the power line has high distortion, maximum power will be affected adversely, although, from a listening standpoint, this is not very critical.)POWER BANDWIDTH(-3dB points): 12Hz to 40kHzFREQUENCY RESPONSE-INPUT SENSITIVITY.55V RMS for rated outputINPUT IMPEDANCE100K ohms, nominalOUTPUT TAPS-OUTPUT REGULATIONApproximately 0.3dB 16-ohm load to open circuitOVERALL NEGATIVE FEEDBACK20dBDAMPING FACTORApproximately 30DISTORTION-SLEW RATE20V/µsRISE TIME2.0 µsHUM & NOISELess than 2.0mV RMS - 84dB below-rated output (20kHz bandwidth unweighted, inputs shorted)POWER SUPPLY ENERGY STORAGEApproximately 280 joulesPOWER REQUIREMENTS105-125VAC 60Hz (210-250VAC 50Hz) 500 watts at rated output, 700 watts maximum, 370 watts at idleTUBE COMPLEMENT(4 matched pairs) 6550 power output, (4) 6FQ7/6CG7 driversDIMENSIONS19 (48 cm) W (standard rack panel) x 7 (18 cm) H x 15 ¾ (40 cm) D (front panel back). Handles extend 1 ? (4.1 cm) forward of the front panel. Output connectors extend 1 behind the rear panel.WEIGHT63 lbs (28.64 kg) Net, 76 lbs (34.55 kg) Shipping

2 - AUDIO RESEARCH D-125 OUTPUT TRANSFORMER (PAIR) PART N: 60007830E WTC - WORKING PROPERLY, TESTED.

The Classic 60 Hybrid Stereo Power Amplifier resembles the long-popular D115 in Audio Researchs family of High Definition® power amplifiers. But its lineage is strictly Classic 150. Which means nothing less than state-of-the-art in design, construction, musicality, and operational convenience...at an affordable price. Like the Classic 150, the Classic 60 proceeds from the notion that power ratings dont always describe a power amplifiers real capabilities. Far more important are such qualities as dynamic stability. lucidity, subtlety. And to achieve those, Audio Research has used its traditional partial cathode coupling along with triode operation of the Classic 60s eight 6550 power output tubes. Additional circuit improvements, as well as the usual rigorous parts selection and manufacturing Audio Research, are noted for, also contributing sonically. Translated into the language of listening, this signifies stunning bandwidth, a noise floor virtually beneath audibility, and musically fulfilling SPLs at dramatically lower gain settings. Dynamics, timbres of individual instruments, soundstage, and musical emotion all surge out from a black velvet of silence. Simply put the Classic 60 resolves far more of a musical program than amplifiers rated at two, three, or four times its seemingly modest 60 WPC. But the Classic 60 is easily up to the task of driving all but the most demanding loudspeakers, even in spacious listening rooms. And while it shows modest preamplifiers in their best light, it also shines when coupled with premiere designs, such as Audio Researchs SP14 or SP15. Convenience figures are high on the Classic 60s list of attributes, as well. For example, the DC balance of the output tubes is maintained automatically, while tube biasing continuously adjusts to changes in incoming line voltage. Performance stays razor-sharp without bothersome tweaking or adjustments. And quiet fan cooling, along with triode operation, means significantly longer tube life. A Classic 60 owner can look forward to years of low-maintenance performance POWER OUTPUT60 watts minimum continuous at 16 ohms from 15Hz to 20kHz with less than 1.0% total harmonic distortion. Typically below .005% at 1 watt. The approximate actual power available at clipping: 62 watts. (1kHz) (Note that the actual RMS power output is dependent upon both line voltage and condition ie: if the power line has high distortion, maximum power will be affected adversely, although, from a listening standpoint, this is not very critical.)POWER BANDWIDTH(-3dB points): 12Hz to 40kHzFREQUENCY RESPONSE-INPUT SENSITIVITY.55V RMS for rated outputINPUT IMPEDANCE100K ohms, nominalOUTPUT TAPS-OUTPUT REGULATIONApproximately 0.3dB 16-ohm load to open circuitOVERALL NEGATIVE FEEDBACK20dBDAMPING FACTORApproximately 30DISTORTION-SLEW RATE20V/µsRISE TIME2.0 µsHUM & NOISELess than 2.0mV RMS - 84dB below-rated output (20kHz bandwidth unweighted, inputs shorted)POWER SUPPLY ENERGY STORAGEApproximately 280 joulesPOWER REQUIREMENTS105-125VAC 60Hz (210-250VAC 50Hz) 500 watts at rated output, 700 watts maximum, 370 watts at idleTUBE COMPLEMENT(4 matched pairs) 6550 power output, (4) 6FQ7/6CG7 driversDIMENSIONS19 (48 cm) W (standard rack panel) x 7 (18 cm) H x 15 ¾ (40 cm) D (front panel back). Handles extend 1 ? (4.1 cm) forward of the front panel. Output connectors extend 1 behind the rear panel.WEIGHT63 lbs (28.64 kg) Net, 76 lbs (34.55 kg) Shipping

AUDIO RESEARCH D-125 OUTPUT TRANSFORMER (PAIR) PART N: 60007830E WTC - WORKING PROPERLY, TESTED.

Cleaned and disinfected. Tested and works great with no issues. Minor usage wear as shown in the pictures. Nothing that affects its functionality. Comes with a newly installed battery and a new spare bateery. See pictures for full descriptions. Sold as pictured. We do our best to accurately picture and describe each one of our listings. Inevitably, you may receive an item that does not meet your expectations. It is no way our intention to mislead or cheat any customer. If you have any issues with your purchase, please message us before filing a refund request. Please note that all refund requests, will require the return of the item in the same condition as it was sent. Any damage or material change to the condition of the item may result in a reduced refund, up to 50% in accordance with eBay policy. All refunds on returns will be processed minus the original shipping charges that were incurred to ship it to you. We package our items in the most cost/time effective way to provide competitive pricing. Should you require special shipping considerations (e.g. packaging or shipping timelines), please message us PRIOR to purchasing so we can work towards an amicable solution. Certain requests may incur additional charges. Post purchase shipping demands will not be honored. Delivery times provided by eBay are estimates. Actual delivery times may vary due to carrier related delays. We ship items as quickly as possible, but in some circumstances it can take up to three business days for an item to be shipped. Once an item leaves our hand, we have no control over when it gets delivered. We only ship to the confirmed shipping address provided to us by eBay at time of purchase. We cannot change the delivery address after a purchase has been made, so please ensure that your shipping address is correct.

The Classic 60 Hybrid Stereo Power Amplifier resembles the long-popular D115 in Audio Researchs family of High Definition® power amplifiers. But its lineage is strictly Classic 150. Which means nothing less than state-of-the-art in design, construction, musicality, and operational convenience...at an affordable price. Like the Classic 150, the Classic 60 proceeds from the notion that power ratings dont always describe a power amplifiers real capabilities. Far more important are such qualities as dynamic stability. lucidity, subtlety. And to achieve those, Audio Research has used its traditional partial cathode coupling along with triode operation of the Classic 60s eight 6550 power output tubes. Additional circuit improvements, as well as the usual rigorous parts selection and manufacturing Audio Research, are noted for, also contributing sonically. Translated into the language of listening, this signifies stunning bandwidth, a noise floor virtually beneath audibility, and musically fulfilling SPLs at dramatically lower gain settings. Dynamics, timbres of individual instruments, soundstage, and musical emotion all surge out from a black velvet of silence. Simply put the Classic 60 resolves far more of a musical program than amplifiers rated at two, three, or four times its seemingly modest 60 WPC. But the Classic 60 is easily up to the task of driving all but the most demanding loudspeakers, even in spacious listening rooms. And while it shows modest preamplifiers in their best light, it also shines when coupled with premiere designs, such as Audio Researchs SP14 or SP15. Convenience figures are high on the Classic 60s list of attributes, as well. For example, the DC balance of the output tubes is maintained automatically, while tube biasing continuously adjusts to changes in incoming line voltage. Performance stays razor-sharp without bothersome tweaking or adjustments. And quiet fan cooling, along with triode operation, means significantly longer tube life. A Classic 60 owner can look forward to years of low-maintenance performance POWER OUTPUT60 watts minimum continuous at 16 ohms from 15Hz to 20kHz with less than 1.0% total harmonic distortion. Typically below .005% at 1 watt. The approximate actual power available at clipping: 62 watts. (1kHz) (Note that the actual RMS power output is dependent upon both line voltage and condition ie: if the power line has high distortion, maximum power will be affected adversely, although, from a listening standpoint, this is not very critical.)POWER BANDWIDTH(-3dB points): 12Hz to 40kHzFREQUENCY RESPONSE-INPUT SENSITIVITY.55V RMS for rated outputINPUT IMPEDANCE100K ohms, nominalOUTPUT TAPS-OUTPUT REGULATIONApproximately 0.3dB 16-ohm load to open circuitOVERALL NEGATIVE FEEDBACK20dBDAMPING FACTORApproximately 30DISTORTION-SLEW RATE20V/µsRISE TIME2.0 µsHUM & NOISELess than 2.0mV RMS - 84dB below-rated output (20kHz bandwidth unweighted, inputs shorted)POWER SUPPLY ENERGY STORAGEApproximately 280 joulesPOWER REQUIREMENTS105-125VAC 60Hz (210-250VAC 50Hz) 500 watts at rated output, 700 watts maximum, 370 watts at idleTUBE COMPLEMENT(4 matched pairs) 6550 power output, (4) 6FQ7/6CG7 driversDIMENSIONS19 (48 cm) W (standard rack panel) x 7 (18 cm) H x 15 ¾ (40 cm) D (front panel back). Handles extend 1 ? (4.1 cm) forward of the front panel. Output connectors extend 1 behind the rear panel.WEIGHT63 lbs (28.64 kg) Net, 76 lbs (34.55 kg) Shipping

32nd item of my dads stereo collection in his estate sale

Up for sale is a custom made, audiophile grade, two tonearm turntable of the highest quality. This unit was obtained from the estate of serious music lover. He had it custom made for him when he lived in California. The unit is a complete two tonearm system. One arm is a fine SAEC-308SX tonearm with a new Audio Technica AT-120E moving magnet cartridge loaded in a Nagaoka AL-703 headshell.The second arm is an extremely nice Fidelity Research FR-645 tonearm with a professionally retyped Fidelity Research FR-1 MK3 moving coil cartridge loaded in a second Nagaoka AL-703 headshell. The turntable itself is a quartz locking direct drive Denon DP-6000. The tonearms and turntable are mounted in a very heavy custom made solid wood plinth. The hinged cover is custom made from heavy clear Plexiglas. Included is a 120-100 volt step down transformer (Toyoden CD110) to be used with he Denon. I was told that the Denon could be used without the step-down transformer but the use of the transformer will prolong the transforms life. All the pieces of this system are in excellent condition with the exception of a few minor places on the plinth were the high gloss finish has come off. Please see the pictures for a true representation of the condition of the equipment. Here is an itemization of the equipment that makes up this unique turntable: Denon DP-6000 turntableSAEC 308SX TonearmAudio Tecnica AT-120E moving magnet cartridgeFidelity Research FR-645 TonearmFidelity Research FR-1 MK3 moving coil cartridge2 Nagaoka AL-703 headshellsCustom oak wood plinth with hinged plexiglas cover and vibration absorbing feet2 custom made 5 pin to RCA/ground tonearm cablesVarious original and copied owners manualsEverything has been tested and works perfectly. The Audio Technica cartridge has less than 15 hours of use on it. The Fidelity Research cartridge was professionally retipped on 10/23. It is in perfect condition as attested by both listening and visual microscopic inspection. If you have read this far I am sure you know both the uniqueness and quality of this unit. If you were to add up the cost of putting this system together the cost would be staggering. I could part this beauty out for more profit but I feel it needs to stay together. I am listing this for local pickup only. If you need to have it shipped please contact me about arrangements and cost.

This is a sealed new in box set new old stock of gold plated audio/ video cables. Copyright date of 2002 on the packaging. If you are over charged for first class shipping, I will refund you the difference, or you can request a new invoice and I will send it to you.

TRANSFORMER TUBE AUDIO OUTPUT AUDIO RESEARCH D-125 (PAIR), WORKING PROPERLY, TESTED.PART N: 60007830E WTC

Verkaufe 1 Paar Röhrenendstufen Audio Research Reference 600 MK III / Top-Zustand / Manual; Geräte stammen aus einem tierlosen Nichtraucherhaushalt und wurden pfleglich behandelt; Die Monos kommen mit einem komplett neuer und ungespielter Röhren aus 2021 (Rechnung vorhanden);OVP ist nicht vorhanden, ein transportsicherer Versand ist ohne Probleme möglich, Versandkosten innerhalb BRD betragen 100,-- EUR zu Lasten des Käufers; Alle von mir bei eBay eingestellten Artikel sind nach bestem Wissen & Gewissen gesichtet und beschrieben worden. Die von mir erkannten Mängel werden in der Artikelbeschreibung benannt. Jedoch erheben sie keinen Anspruch auf Vollständigkeit, die sich gerade bei älteren Artikeln schon aus der Sache heraus ergeben können. Die eingestellten Bilder sind vom Original erstellt worden. Es ist nichts fototechnisch entstellt oder verändert worden. Ich gewähre 12 Monate Gewährleistung. Inzahlungnahmen sind möglich. Die MwSt ist nicht ausweisbar (§25 UStG Differenzbesteuerung) Bei weiteren Fragen, einfach Kontakt aufnehmen. Ich bin Fachhändler für diverse Hifi Produkte.

In excellent condition. Tested and runs great! Used very minimally throughout its life. Been in storage for a while in a climate controlled condition. Very rare amp! *The testing was to the extent that it turns on, and fires up correctly. Didn’t have a system to test it on beyond that. * sold AS IS. One Fuse + cap is missing. Pls reference pics for exact details and condition Do not miss out on this one! Thank you for looking and happy shopping!

The Classic 60 Hybrid Stereo Power Amplifier resembles the long-popular D115 in Audio Researchs family of High Definition® power amplifiers. But its lineage is strictly Classic 150. Which means nothing less than state-of-the-art in design, construction, musicality, and operational convenience...at an affordable price. Like the Classic 150, the Classic 60 proceeds from the notion that power ratings dont always describe a power amplifiers real capabilities. Far more important are such qualities as dynamic stability. lucidity, subtlety. And to achieve those, Audio Research has used its traditional partial cathode coupling along with triode operation of the Classic 60s eight 6550 power output tubes. Additional circuit improvements, as well as the usual rigorous parts selection and manufacturing Audio Research, are noted for, also contributing sonically. Translated into the language of listening, this signifies stunning bandwidth, a noise floor virtually beneath audibility, and musically fulfilling SPLs at dramatically lower gain settings. Dynamics, timbres of individual instruments, soundstage, and musical emotion all surge out from a black velvet of silence. Simply put the Classic 60 resolves far more of a musical program than amplifiers rated at two, three, or four times its seemingly modest 60 WPC. But the Classic 60 is easily up to the task of driving all but the most demanding loudspeakers, even in spacious listening rooms. And while it shows modest preamplifiers in their best light, it also shines when coupled with premiere designs, such as Audio Researchs SP14 or SP15. Convenience figures are high on the Classic 60s list of attributes, as well. For example, the DC balance of the output tubes is maintained automatically, while tube biasing continuously adjusts to changes in incoming line voltage. Performance stays razor-sharp without bothersome tweaking or adjustments. And quiet fan cooling, along with triode operation, means significantly longer tube life. A Classic 60 owner can look forward to years of low-maintenance performance POWER OUTPUT60 watts minimum continuous at 16 ohms from 15Hz to 20kHz with less than 1.0% total harmonic distortion. Typically below .005% at 1 watt. The approximate actual power available at clipping: 62 watts. (1kHz) (Note that the actual RMS power output is dependent upon both line voltage and condition ie: if the power line has high distortion, maximum power will be affected adversely, although, from a listening standpoint, this is not very critical.)POWER BANDWIDTH(-3dB points): 12Hz to 40kHzFREQUENCY RESPONSE-INPUT SENSITIVITY.55V RMS for rated outputINPUT IMPEDANCE100K ohms, nominalOUTPUT TAPS-OUTPUT REGULATIONApproximately 0.3dB 16-ohm load to open circuitOVERALL NEGATIVE FEEDBACK20dBDAMPING FACTORApproximately 30DISTORTION-SLEW RATE20V/µsRISE TIME2.0 µsHUM & NOISELess than 2.0mV RMS - 84dB below-rated output (20kHz bandwidth unweighted, inputs shorted)POWER SUPPLY ENERGY STORAGEApproximately 280 joulesPOWER REQUIREMENTS105-125VAC 60Hz (210-250VAC 50Hz) 500 watts at rated output, 700 watts maximum, 370 watts at idleTUBE COMPLEMENT(4 matched pairs) 6550 power output, (4) 6FQ7/6CG7 driversDIMENSIONS19 (48 cm) W (standard rack panel) x 7 (18 cm) H x 15 ¾ (40 cm) D (front panel back). Handles extend 1 ? (4.1 cm) forward of the front panel. Output connectors extend 1 behind the rear panel.WEIGHT63 lbs (28.64 kg) Net, 76 lbs (34.55 kg) Shipping

This is a sealed new in box set new old stock of gold plated audio/ video cables. Copyright date of 2002 on the packaging. If you are over charged for first class shipping, I will refund you the difference, or you can request a new invoice and I will send it to you.

The Classic 60 Hybrid Stereo Power Amplifier resembles the long-popular D115 in Audio Researchs family of High Definition® power amplifiers. But its lineage is strictly Classic 150. Which means nothing less than state-of-the-art in design, construction, musicality, and operational convenience...at an affordable price. Like the Classic 150, the Classic 60 proceeds from the notion that power ratings dont always describe a power amplifiers real capabilities. Far more important are such qualities as dynamic stability. lucidity, subtlety. And to achieve those, Audio Research has used its traditional partial cathode coupling along with triode operation of the Classic 60s eight 6550 power output tubes. Additional circuit improvements, as well as the usual rigorous parts selection and manufacturing Audio Research, are noted for, also contributing sonically. Translated into the language of listening, this signifies stunning bandwidth, a noise floor virtually beneath audibility, and musically fulfilling SPLs at dramatically lower gain settings. Dynamics, timbres of individual instruments, soundstage, and musical emotion all surge out from a black velvet of silence. Simply put the Classic 60 resolves far more of a musical program than amplifiers rated at two, three, or four times its seemingly modest 60 WPC. But the Classic 60 is easily up to the task of driving all but the most demanding loudspeakers, even in spacious listening rooms. And while it shows modest preamplifiers in their best light, it also shines when coupled with premiere designs, such as Audio Researchs SP14 or SP15. Convenience figures are high on the Classic 60s list of attributes, as well. For example, the DC balance of the output tubes is maintained automatically, while tube biasing continuously adjusts to changes in incoming line voltage. Performance stays razor-sharp without bothersome tweaking or adjustments. And quiet fan cooling, along with triode operation, means significantly longer tube life. A Classic 60 owner can look forward to years of low-maintenance performance POWER OUTPUT60 watts minimum continuous at 16 ohms from 15Hz to 20kHz with less than 1.0% total harmonic distortion. Typically below .005% at 1 watt. The approximate actual power available at clipping: 62 watts. (1kHz) (Note that the actual RMS power output is dependent upon both line voltage and condition ie: if the power line has high distortion, maximum power will be affected adversely, although, from a listening standpoint, this is not very critical.)POWER BANDWIDTH(-3dB points): 12Hz to 40kHzFREQUENCY RESPONSE-INPUT SENSITIVITY.55V RMS for rated outputINPUT IMPEDANCE100K ohms, nominalOUTPUT TAPS-OUTPUT REGULATIONApproximately 0.3dB 16-ohm load to open circuitOVERALL NEGATIVE FEEDBACK20dBDAMPING FACTORApproximately 30DISTORTION-SLEW RATE20V/µsRISE TIME2.0 µsHUM & NOISELess than 2.0mV RMS - 84dB below-rated output (20kHz bandwidth unweighted, inputs shorted)POWER SUPPLY ENERGY STORAGEApproximately 280 joulesPOWER REQUIREMENTS105-125VAC 60Hz (210-250VAC 50Hz) 500 watts at rated output, 700 watts maximum, 370 watts at idleTUBE COMPLEMENT(4 matched pairs) 6550 power output, (4) 6FQ7/6CG7 driversDIMENSIONS19 (48 cm) W (standard rack panel) x 7 (18 cm) H x 15 ¾ (40 cm) D (front panel back). Handles extend 1 ? (4.1 cm) forward of the front panel. Output connectors extend 1 behind the rear panel.WEIGHT63 lbs (28.64 kg) Net, 76 lbs (34.55 kg) Shipping

This is a sealed new in box set new old stock of gold plated audio/ video cables. Copyright date of 2002 on the packaging. If you are over charged for first class shipping, I will refund you the difference, or you can request a new invoice and I will send it to you.