Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #7 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.The appearance is a beautiful product without any noticeable scratches. With original box. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Titanium NitrideArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmRotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5gShell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 38mm? Accessories WeightsWeight fixing screwMounting nut/washerHead shell/lead wireCartridge fixing screwsPHONO cableInstruction Manual (original) (Japanese)Mounting gaugeSpannerFlat head screwdriverOriginal box / Outer box Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Panasonic Ramsa Audio Mixer WR-M10A With Rackmount Ears Working 100% Like NeuDie Beschreibung dieses Artikels erfolgte durch automatische Übersetzung. Bei anstehenden Fragen, wenden Sie sich bitte an uns.PANASONIC Ramsa Audio Mixer WR-M10A mit Rackmount-Ohren funktioniert 100 % wie neuPANASONIC Ramsa Audio Mixer WR-M10A mit Rackmount-Ohren funktioniert 100 % wie neu Garantía del fabricante Sin garantía EAN No aplicable Marca Panasonic País/Región de fabricación Japón Modelo RAMSA Wr-X01A Número de canales 4

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #6 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.The appearance is a beautiful product without any noticeable scratches. With original box. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Titanium NitrideArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmRotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5gShell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 38mm? Accessories WeightWeight fixing screwMounting nuts/washersHead shell/lead wireCartridge fixing screwsPHONO cableInstruction Manual (copy)Mounting gaugeSpannerFlat head screwdriverOriginal box Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Welcome to Audio/Video Archives, the largest home of audio literature available on eBay! This is a Reprinted Nak T-100 Analyzer Brochure from 1980. It will have Pictures and Articles of the item listed along with Specifications, Articles, Information and Commentary. The Picture is of the actual item. It is a beautiful piece of Audio History. I have THOUSANDS more from every major brand of Audio from 1950 up to now. ---Satisfaction is GUARANTEED at AV Archives! Take a look at my feedback for satisfied customers! I have been open since 2007 and have sold THOUSANDS of Ads, Reviews, and Brochures to satisfied customers. ---I Ship Worldwide and combine shipping, each additional item is just $1 after the first is paid. ---Each Page is 8.5 by 11 unless otherwise noted in title. ---Single-Sided professional matte photo pages, unless otherwise noted in the title. ---These Ads and Reviews are perfect for framing and placed in your Audio Room. ---I have a HUGE Vinyl Record Store with Thousands of Collectable records, and MANY First Pressings/Audiophile LPs. Just click on my Vinyl Record Store link on the left under categories. Email me for any specific questions, You will hear back from me usually within 4 hours, THANK YOU! Greg Powered by eBay Turbo Lister The free listing tool. List your items fast and easy and manage your active items.

Welcome to Audio/Video Archives, the largest home of audio literature available on eBay! This is a Reprinted Nak T-100 Analyzer Brochure from 1980. It will have Pictures and Articles of the item listed along with Specifications, Articles, Information and Commentary. The Picture is of the actual item. It is a beautiful piece of Audio History. I have THOUSANDS more from every major brand of Audio from 1950 up to now. ---Satisfaction is GUARANTEED at AV Archives! Take a look at my feedback for satisfied customers! I have been open since 2007 and have sold THOUSANDS of Ads, Reviews, and Brochures to satisfied customers. ---I Ship Worldwide and combine shipping, each additional item is just $1 after the first is paid. ---Each Page is 8.5 by 11 unless otherwise noted in title. ---Single-Sided professional matte photo pages, unless otherwise noted in the title. ---These Ads and Reviews are perfect for framing and placed in your Audio Room. ---I have a HUGE Vinyl Record Store with Thousands of Collectable records, and MANY First Pressings/Audiophile LPs. Just click on my Vinyl Record Store link on the left under categories. Email me for any specific questions, You will hear back from me usually within 4 hours, THANK YOU! Greg Powered by eBay Turbo Lister The free listing tool. List your items fast and easy and manage your active items.

Habe den Verstärker neu gekauft und dann aber doch nicht verwendet ,Funkitoniert einwandfrei . Lieferung der Verstäker100W HiFi Verstärker HOLLYWOOD Mini-100 Amplifier Audio Stereo Cinch AUX DJ PA mit Netzteil Privatverkauf Keine Garantie und keine Rücknahme

This Advertisement is a reprint from 1994. It is on glossy photo paper and is in Excellent condition! The Picture is the picture of the actual item. It is a beautiful piece of Audio History. I have THOUSANDS more from every major brand of Audio from 1950 up to now. ---Satisfaction is GUARANTEED at AV Archives! Take a look at my feedback for satisfied customers! I have been open since 2007 and have sold THOUSANDS of Ads, Reviews, and Brochures to satisfied customers. ---I Ship Worldwide and combine shipping, each additional item is just $1 after the first is paid. ---Each Page is 8.5 by 11 unless otherwise noted in title. ---Single Page, Single Sided Ads, unless otherwise noted in the title. ---These Ads are perfect for framing and placed in your Audio Room. ---I have a HUGE Vinyl Record Store with Thousands of Collectable records, and MANY First Pressings/Audiophile LPs. Just click on my Vinyl Record Store link on the left under categories. Email me for any specific questions, You will hear back from me usually within 4 hours, THANK YOU! Greg

Habe den Verstärker neu gekauft und dann aber doch nicht verwendet ,Funkitoniert einwandfrei . Lieferung der Verstäker100W HiFi Verstärker HOLLYWOOD Mini-100 Amplifier Audio Stereo Cinch AUX DJ PA mit Netzteil Privatverkauf Keine Garantie und keine Rücknahme

Welcome to C2 Auction Join Mailing List Add to Favourites Store Home Items For Sale Feedback Contact Us Stewart Audio PA-50B Power Amplifier 100 Watt Power Amplifier Product Description Description:Stewart Audio PA-50B Power Amplifier 100 Watt Power AmplifierSerial Number: QDKJ421Functional Condition:The item: is guaranteed to be fully functionalTests performed: Unit powered on. Tested with in house audio and speakers on both channels. Sound is clear at low to high volume.Cosmetic Condition:Item is in good used condition.Items Included:Stewart Audio PA-50B Power Amplifier 100 Watt Power Amplifier Data Sanitization Status: Evaluated as not containing data Cosmetic Code: C4 Used Good Functionality Code: F4 Hardware Functional SKU: A-36243 Business & Industrial Computers, Tablets & Network Hardware Medical & Lab Gear View all Categories ITEMS WE SELL Consumer Electronics Business & Industrial Equipment Information Technology Equipment Computers, Servers, Switches Restaurant & Hospitality Lab & Medical Equipment Cabling, Steel, Copper, Aluminum Vehicles & Large Equipment Assets We Specialize In IT & Computers Business & Industrial Test & Measurement Lab & Scientific Audio & Video Manufacturing Research & Development Parts & Components Supplies & Disposables SPECIALIZING IN THE DISPOSITION OF BUSINESS ASSETS ASSET RECOVERY C2 believes re-use is the highest form of recycling. We test, repair, resell and offer revenue sharing. ELECTRONICS RECYCLING C2 can handle all your electronics recycling needs from batteries to mainframes. C2 accepts anything with a plug large or small. DATA DESTRUCTION C2 can destroy client data at your site or at our secure facility. COD and video provided at end of each job. RIGGING & REMOVAL C2 can destroy client data at your site or at our secure facility. COD and video provided at end of each job. “C2 has grown to meet the needs of all clients large and small. When it comes to asset recovery and electronics recycling C2 can carry the load!” About Us C2 Management is an industry leader in the responsible disposition of surplus: Business and Industrial Electronics Government Surplus Property Data Containing Devices Lab and Test Equipment Large and Proprietary Equipment For both corporate and government clients. We are experts in e-waste recycling, re-use, removal, and secure data destruction. We make sure electronics are disposed of properly while the health and safety of our clients, employees, and the environment are our primary concern. No matter what your struggle is in managing your excess assets, leave it to us. We’ll C2 it. Payment We accept payments through eBay managed payments, contact us to check the availability of other payment methods Shipping PLEASE NOTE: If you think an accessory should be with this item, and it is not pictured or mentioned, it is NOT INCLUDED. *** We apologize, but we do not offer shipping on customer accounts. Shipment is solely via UPS, unless otherwise specified. Buying more items from us? We offer a discount for additional purchases that can be shipped together. Please contact us after the first item won to notify us that you are still bidding (do not make payment)....You will then have 6 additional days to continue bidding. Please contact us by the 6th day to request your combined shipping invoice, and we will require payment by the 7th day. *** LOCAL CUSTOMER PICK UPS ARE NO LONGER AVAILABLE *** International Buyers -- Please Note: ** Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying. Returns Returns allowed for 30 days unless otherwise noted. We will pay return shipping for damaged, Non-functional, or not as described items. As described, arrived on time, great seller Buyer: B***E (125) Happy, good postage deal with anytime Buyer: I***P (69) No problems, product as described, good communication, pleasant and stress free Buyer: R***Y (509) Great thanks. Fast & hassle free. Highly recommend AAAA+++++ Buyer: R***Y (509) Sign Up For Our Newsletter Click here to subscribe to our newsletter and to receive all the latest news, updates and special offers about our store. Subscribe Now Useful Links Store Home Items For Sale Feedback Contact Us Payment Options Shop With Confidence © Copyright 2021, CIE International LLC. All rights reserved.

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage AudioDescriptionThe universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium and further hardened with nitrogen, to achieve 1.6 times mechanical strength and high internal loss while reducing weight by 85% compared to conventional aluminum pipe. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Type Braking variable dynamic damping systemUniversal tone armEffective bearing distance 30mm both horizontally and verticallyArm pipe High-strength titanium pipe with special nitriding treatmentArm effective length 250mmArm overall length range 322mm?350mmArm rear length range 66mm - 94mmArm height adjustment mechanism 45mm - 90mm (helicoid part 6mm)Overhang 15mmHorizontal tracking error angle +1.1°(inside of 30cm record)+2.1°(30cm record circumference)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency 9.8Hz(Compliance: 12x10-6cm/dyneCartridge dead weight: 6.5g, needle pressure: 1.25g)Arm resonance sharpness (Q) 6dB or less (at optimum adjustment)Needle pressure adjustment range 0 to 3gShell weight 9.5gCartridge mounting dimensions JIS standard 12.7mm (1/2) mounting distanceShell terminal lug 1.2mm?, lug for 4-pin terminalApplicable cartridge weight 5g-10gArm mounting hole diameter 38mm?Optional: SH-100G1 balance weight for EPA-100 ($20,000)Type Variable dynamic damping typeArm effective weight 25.5g (with cartridge dead weight 9.5g and needle pressure 1.25g)Arm resonance frequency 9.1Hz(Compliance: 12x10-6cm/dyneCartridge dead weight: 9.5g, needle pressure: 1.25g)Resonance sharpness (Q) 6dB (at optimum adjustment)Dimensions 66mm - 94mm (from horizontal rotation axis to highest part of weight) Shipping FedEx?or DHLInternational Buyers - Please Note:Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying. Thank you for your understanding.

VINTAGE, MATCHED PAIR 2 x MULLARD PL300 VALVE / TUBE DOUBLE RING SIDE GETTER DIRECT EQUIVALENT TO: 35FN5 - CV10783 NEW OLD STOCK / UNUSED Tested on a Sencore 162 MK7 TEST TO NOS SPEC. / 100% No shorts etc., life test Excellent, Gas test good THESE ITEMS HAVE BEEN IN LONG TERM STORAGE, AND MAY HAVE DUST / STORAGE MARKS / USER MARKS ETC. PLEASE SEE PICTURES ABOVE FOR FURTHER DETAILS, REGARDING THE PHYSICAL CONDITION Note!! 20% import / VAT tax applies to EU buyers, all other International buyers may also have to pay Import Tax etc. This is now automatically added by E-bay. All items will be well packed and send in a box with plenty of packaging material All items are send via tracked and or signed for Royal Mail postage service All items have been tested and are sold in working condition, unless otherwise stated in the description. Items can not be sent to a PO box

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #4 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.The appearance is a beautiful product without any noticeable scratches. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories WeightsWeight fixing screwHead shell (Technics)Lead wireMounting nut/washerPHONO cableInstruction Manual (copy)(Japanese)Installation gauge (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Technics EPA-100 Braccio pickup universale con smorzamento dinamico Audio vintage n. 4 Domo Arigato! Benvenuto, grazie per la tua visita. Descrizione Operazione confermata con i seguenti contenuti. Uscita da entrambi i canali.Velocità di discesa del sollevatore (Rifornimento olio).Ogni punto di regolazione, sensazione di funzionamento.Regolazione dellaltezza, ecc. Lucidato e pulito in ogni sua parte.Laspetto è un bellissimo prodotto senza graffi evidenti. Si prega di fare riferimento alla foto. Panoramica Il braccio universale è stato sviluppato per risolvere il problema principale dello smorzamento della risonanza a bassa frequenza nei sistemi di pickup. Il meccanismo di smorzamento dinamico variabile è in grado di smorzare adeguatamente le risonanze a bassa frequenza sia di tipo ad alta che a bassa compliance, esaltando tutto il potenziale della cartuccia. Il peso principale è diviso e supportato da una molla su un lato, e galleggia sullaltro lato grazie alla forza di attrazione tra due magneti posizionati uno di fronte allaltro nella parte posteriore del peso e del selettore di smorzamento. La risonanza del peso viene smorzata da olio siliconico viscoso e da un cilindro di smorzamento, smorzando efficacemente la risonanza dellintero sistema di pickup e riducendo con successo la risonanza a meno della metà rispetto ai sistemi convenzionali. La frequenza di risonanza del peso principale può essere regolata con il selettore di smorzamento sul retro del peso principale in base alla conformità della cartuccia, e la quantità di frenata può essere impostata su un valore appropriato. Il tubo del braccio, con diametro esterno di 9,5 mm e spessore di 0,5 mm, è realizzato con un braccio in nitruro di titanio, realizzato in titanio leggero e meccanicamente resistente, ulteriormente indurito dallazoto. La struttura di supporto del braccio è realizzata in tubo di nitruro di titanio. Sia la sezione di rotazione orizzontale che quella verticale del braccio sono supportate da un sistema di sospensione cardanica che utilizza cuscinetti con cuscinetti girevoli ad alta precisione prodotti internamente. Gli assi di rotazione orizzontale e verticale si intersecano in un unico punto, riducendo al minimo le differenze nella sensibilità iniziale e nella sensibilità in tutte le direzioni di rotazione. I rubini, il cui coefficiente di attrito è circa 1/3 di quello dellacciaio, vengono superfiniti in sfere con una sfericità di ±0,5?m e vengono utilizzati 20 rubini.In combinazione con il sistema di sospensione cardanica, raggiunge unelevata sensibilità iniziale di 5 mg. Specifiche Tipo: braccio universale con smorzamento dinamico variabileGioco effettivo dei cuscinetti: 30 mm sia in orizzontale che in verticaleTubo del braccio: tubo al boro titanioLunghezza effettiva del braccio: 250 mmIntervallo di lunghezza del braccio: da 322 mm a 350 mmIntervallo di lunghezza posteriore del braccio: 66,5 mm - 94,5 mmIntervallo di regolazione dellaltezza del braccio: 44 mm - 64 mm (parte elicoidale 20 mm)Sporgenza: 15 mmAngolo di errore di tracciamento orizzontale: +1°6(circonferenza interna del record da 30 cm), +2°6(circonferenza esterna del record da 30 cm)Sensibilità dellasse di rotazione: sensibilità orizzontale, verticale, iniziale 5 mgPeso effettivo del braccio: 22 g (peso morto della cartuccia 6,5 g, pressione dellago 1,25 g)Frequenza di risonanza del braccio: 9,8 Hz, (Conformità: 12x10-6 cm/dyne, peso cartuccia 6,5 g, pressione ago 1,25 g)Nitidezza della risonanza del braccio (Q): 6 dB o meno (con regolazione ottimale)Intervallo di regolazione della pressione dellago: da 0 a 3 gPeso del guscio: 9,5 g (alluminio boro)Capocorda terminale a guscio: 1,2 mm?, capocorda per terminale a 4 pinPeso della cartuccia applicabile: da 5 g a 10 gDiametro del foro di montaggio del braccio: 62 mm? Accessori PesiVite di fissaggio del pesoGuscio della testa (Tecnica)Cavo principaleDado/rondella di montaggioCavo FONOManuale di istruzioni (copia)(giapponese)Calibro di installazione (copia) Spedizione La spedizione è disponibile solo per lindirizzo registrato su eBay. La spedizione è entro Fedex O SME. Spedizione gratuita ritorna Politica di restituzione incondizionata Il servizio e la soddisfazione del cliente sono molto importanti per noi.Ho una politica di restituzione incondizionata se notificata entro 30 giorni dalla ricezione dellarticolo. Tutti gli articoli restituiti devono essere nella condizione originale.Tutte le richieste di reso devono essere effettuate entro 30 giorni dal ricevimento dellarticolo. Per favore contattami prima per il reso prima di rispedirmelo.Le spese di spedizione della merce restituita sono a carico dellacquirente. Acquirenti internazionali Notare che:I dazi doganali, le tasse e le spese non sono inclusi nel prezzo dellarticolo o nelle spese di spedizione.Queste spese sono a carico dellacquirente.Si prega di verificare con lufficio doganale del proprio paese per determinare quali saranno questi costi aggiuntivi prima dellofferta/acquisto.Queste spese vengono normalmente riscosse dalla società di spedizione (spedizione) o al momento del ritiro dellarticolo: non confonderle con spese di spedizione aggiuntive.Non contrassegniamo i valori della merce al di sotto del valore né contrassegniamo gli articoli come regali: le normative governative statunitensi e internazionali vietano tale comportamento. Mi dispiace, ma non possiamo organizzarlo perché è illegale in Giappone.Grazie.

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #4 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.The appearance is a beautiful product without any noticeable scratches. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories WeightsWeight fixing screwHead shell (Technics)Lead wireMounting nut/washerPHONO cableInstruction Manual (copy)(Japanese)Installation gauge (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Item condition good used condition with some signs of use Any major flaws will be pointed out in pictures so please study them carefully as these show overall condition of the item Measurements are also in the photos This will be shipped next business day or the same day if purchased before 10am Mon-Fri with a tracking number for confirmation Please feel free to ask any questions most questions answered instantly. Thanks for looking why not check out the rest of my store and Add me as a Saved Seller check back daily for new items Happy to combine shipping on multi quantity purchases Worldwide shipping available through ebays global shipping programme.

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #3 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed.The appearance is a beautiful product without any noticeable scratches. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories All accessories are shown in the photos. Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer?s responsibility.Please check with your country?s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as ?gifts? -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

THIS AUCTION IS FOR ONE CAPACITOR !!! Typically used as a bypass for high frequency tweeter speakers   They are from the late 1950s.   Value is 2.0 uf 100 volt Listing and template services provided by inkFrog

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #3 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed.The appearance is a beautiful product without any noticeable scratches. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories All accessories are shown in the photos. Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer?s responsibility.Please check with your country?s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as ?gifts? -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Sheng Ya/Vincent Audio Sa T-1 Pre Amp & Pair SPT-100 Power Amps. In good working order - sounds great!

Up for sale is a Pair of Emerald Physics 100.2 SE Monobloc AmplifiersCosmetics are GREAT,Tonally GREAT!Manual included.***BEAUTIFUL WORK OF ART***THESE PIECES ARE TRULY BEAUTIFUL !WHEN YOU SEE THEM YOU WILL FALL IN LOVE !LINK BELOW: (GOOD READ)https://hifisoundenthusiast.com/portfolio/ps-audio-and-emerald-physics-100-2-se-pairing-review/ The 100.2SE is a 100 watts per channel stereo power amplifier with a class D output stage coupled to a custom Emerald Physics analog power supply. The 100.2SE is an upgraded version of the 100.2 amp. The 100.2SE has both balanced and single ended inputs as well as a mono switch that allows you to end up with a 275 watt mono amp that does over 350 watt peaks.Specs:100 watts RMS/ch 8 ohms Digital Amp with custom analog power supply150 watts RMS/ch 4 ohmsLess than .03% distortion 1 watt275 watts RMS mono operation Beautiful metal chassis350 watts dynamic power in mono Extremely efficient (~93%)Damping: Greater than 300Dynamic Range: 110dB3 ohm stableInput impedance: 60K Ohms XLR/ 30K Ohms RCARCA & XLR inputsRetail: $2,200.00 EACHWeight: 16 poundsGain: 30dBMade in USA You will be Happy !Check my Feedback ! FAST SHIPPING !

THIS AUCTION IS FOR ONE CAPACITOR !!! Typically used as a bypass for high frequency tweeter speakers   They are from the late 1950s.   Value is 2.0 uf 100 volt Listing and template services provided by inkFrog

VINTAGE, MATCHED PAIR 2 x MULLARD PL300 VALVE / TUBE DOUBLE RING SIDE GETTER DIRECT EQUIVALENT TO: 35FN5 - CV10783 NEW OLD STOCK / UNUSED Tested on a Sencore 162 MK7 TEST TO NOS SPEC. / 100% No shorts etc., life test Excellent, Gas test good THESE ITEMS HAVE BEEN IN LONG TERM STORAGE, AND MAY HAVE DUST / STORAGE MARKS / USER MARKS ETC. PLEASE SEE PICTURES ABOVE FOR FURTHER DETAILS, REGARDING THE PHYSICAL CONDITION Note!! 20% import / VAT tax applies to EU buyers, all other International buyers may also have to pay Import Tax etc. This is now automatically added by E-bay. All items will be well packed and send in a box with plenty of packaging material All items are send via tracked and or signed for Royal Mail postage service All items have been tested and are sold in working condition, unless otherwise stated in the description. Items can not be sent to a PO box

TWS TPA3118 5.0 Scheda Audio Amplificatore Bluetooth Amplificador AUX 100 W X9B4 Bluetooth 5.0, supporta laccoppiamento TWS a una chiave, supporta AUX per inserire TWS nella scatola e mantenere la , accensione, il volume predefinito è TX, RX, GND: configurazione della porta seriale TTL 9600, N, 8, 1A 24V6A, la potenza massima in uscita è 100WA 21V5A, la potenza massima in uscita è 80WAlimentatore 8-22 V, con protezione connessione inversa, supporto per alimentatore per laptopcolore: verdeMateriale: PCBdimensioni: 7,8 x 5,2 cmContenuto della confezione:1 x scheda amplificatore di potenza Bluetooth 5.0

TWS TPA3118 5.0 Scheda Audio Amplificatore Bluetooth Amplificador AUX 100 W M3Z5 Bluetooth 5.0, supporta laccoppiamento TWS a una chiave, supporta AUX per inserire TWS nella scatola e mantenere la , accensione, il volume predefinito è TX, RX, GND: configurazione della porta seriale TTL 9600, N, 8, 1A 24V6A, la potenza massima in uscita è 100WA 21V5A, la potenza massima in uscita è 80WAlimentatore 8-22 V, con protezione connessione inversa, supporto per alimentatore per laptopcolore: verdeMateriale: PCBdimensioni: 7,8 x 5,2 cmContenuto della confezione:1 x scheda amplificatore di potenza Bluetooth 5.0