AIWA XK-S9000 3-Head Stereo Cassette Tape Deck USED FROM JAPAN WorkingDescription Type Stereo cassette deckHead Recording: Stressfree-6N wound pure amorphous headPlayback: Stressfree-6N wound pure amorphous headErase: Double-gap sendust headMotor For capstan: Mu-flat DC servo motorFor playback/recording take-up: DC motorFor FF/RWD: DC motorFor Super AMTS/cassette door: DC motorWah Flutter 0.018%(W, Peak)±0.035%(WRMS)Frequency response (-20dB recording) LH: 13Hz to 21kHz ±3dBCrO2: 13Hz to 22kHz ±3dBMetal: 8Hz to 27kHz -10dB???? 13Hz to 24kHz ±3dBSN ratio (peak level) 65dB (NR off, metal tape)87dB (Dolby S NR on, metal tape)Dimensions 469 (W) x 151 (H) x 415 (D) mmWeight 14.0 kg Reference cassette deck developed for the best sound quality. It uses Dolby S-type noise reduction system.The Dolby S-type is a noise reduction system optimised for consumer cassettes from the professional Dolby SR (Spectral Recording) system used in recording studios, and achieves noise reduction of up to 10 dB in the low frequency range and 24 dB in the high frequency range. It also eliminates the pumping (dynamic side-effects) common to conventional NR, resulting in natural, high quality sound.The Dolby S-type is audibly compatible with the B-type, so it can be played on cassette decks equipped with the B-type. Super A-M-T-S (Super Anti Modulation Tape Stabilizer) prevents tape vibration.Super A-M-T-S is a development of Aiwas original stabilising mechanism, A-M-T-S. The cassette box inherits the two-layer structure of non-magnetic aluminium plates and non-resilient rubber, while the pressure applied to the surface of the half body is strengthened from 1kg to 1.5kg, and is also pressed from the back side with non-resilient rubber of different properties to achieve further vibration reduction.The capstan motor, which is the source of vibration inside the deck, is supported by two three-layer vibration-damping steel plates and special vibration-damping rubber to keep it floating. Furthermore, the recording and playback heads have been reinforced from two-point to three-point support, and are precisely fixed to the heavyweight head block, which is also fitted with a head stabiliser that is dumped from both sides using non-rebounding rubber.These structures provide a thorough vibration-damping mechanism for even higher sound quality. The BTOR (Blank Tape Optimised Recording) system is a recording position dedicated to raw tape.In conventional cassette decks, when recording to a tape that has never been used, it still passes through the erase head, affecting the signal system due to the erase current. This is improved by BTOR to improve sound quality. Real 18-bit linear dual D/A converters allow direct connection from digital sources in digital form.The D/A converter section has an independent dual configuration for left and right channels, and uses a completely independent power supply system consisting of a dedicated D/A converter winding, independent rectification circuits for digital and signal systems and independent power supply circuits to eliminate mutual interference.In addition, the digital section is isolated by a dedicated shield case to minimise the effect on the audio system. In addition, an ON/OFF switch is provided to stop all digital system clocks. The recording and playback heads use stress-free 6N-wound pure amorphous heads.In pursuit of high sound quality, ultra-high purity copper with Stress free-6Nines purity of 99.99997% or higher is used for the head windings without regard to cost; LC-OFC and PC-OCC had 99.99% or higher copper, called 4Nines, but with 6N, impurities are reduced from 100ppm to 1ppm The distortion of the atomic arrangement has been reduced to 1 ppm, disappearing and reducing the turbulence in the flow of electrons.The head core uses a 12-layer laminated pure amorphous head with extremely high magnetic flux density, which has excellent characteristics as an audio magnetic head. The erase head is made of sendust material.The dual capstan mechanism applies a higher and more constant tape tension than a single capstan and provides a higher degree of adhesion between tape and head. For this reason, using normal ferrite material for the erase and record heads causes high-frequency degradation of the tape signal due to the spontaneous magnetisation effect caused by the coercive force = Hc (0.1-0.15) of the ferrite material.The use of sendust erase heads with an extremely low Hc of 0.007-0.02 prevents deterioration of the tapes sound quality. The mechanism uses a four-motor closed-loop dual capstan mechanism.The left and right capstan drive, dedicated FF/REW and recording/playback motors are independent, and a belt-driven low cogging mechanism was developed based on the concept of an analogue thread drive player. Another motor is used for Super A, M, T, S and cassette box drive.The capstan uses Aiwas unique micro-grained frequency-dispersive capstan, which causes less tape damage, and together with the high-precision flywheel, each of which is precisely and dynamically balanced, achieves a wow-flutter figure of 0.018%. A vibration-damping mechanism is employed, with a heavy, highly rigid chassis and cabinet, and a resonance-damping wood base with high-density softwood MDF board on the bottom to reduce external vibrations. In addition, a vibration-damping type printed circuit board with fast vibration damping characteristics is used.Furthermore, attention has been paid to the micro-vibrations caused by the power transformer, and a large anti-vibration, anti-magnetic type power transformer has been externally mounted.In addition, vibration damping is thoroughly pursued through the use of heavyweight insulators, head stabilisers, a head block with a bias shield structure and a three-point support high-rigidity head base. Electronic switches, switching circuits, connectors and printed patterns that cause sound quality degradation have been eliminated as far as possible to ensure simple and straight signal transmission.The transmission mechanism is also equipped with an MPX circuit with a through-position and an open-type muting circuit with a gold-plated relay during performance, which prevents sound quality degradation when the unit is switched off. The printed circuit boards for the digital, mechanical logic, display, signal and Dolby S NR systems are independent of each other and placed at sufficient intervals to eliminate mutual interference.In addition, the mechanical logic and display systems are separated by an internal chassis to eliminate interference with the signal system, and the D/A converter printed circuit board is isolated by a special shield case. Manual calibration is provided to bring out the best tape performance. In addition, the built-in oscillator is set to 400 Hz and 10 kHz for wide frequency response adjustment.In addition, the level meter is expanded in 0.5 dB steps during calibration, allowing highly accurate calibration. Three recording equalisers can be set to suit the recording source and tape.High is a setting that emphasises low-frequency MOL (Maximum Output Leve), Norm is a standard setting and Low is a setting that emphasises high-frequency MOL. Low output impedance power supply with discrete configuration. PC-OCC low capacitance headwires are used and are directly attached to the playback equaliser. PC-OCC wound trap coils with low distortion cores are used. It has a discrete Dolby HX Pro circuit with on/off capability. The system is equipped with an ultra-low distortion Dolby NR IC. The system is equipped with a high-precision detent-type recording volume. 70 micron thick copper foil printed circuit board. Special triple-layer large metallised polyester film capacitors are used. OFC extra-thick power cord with polarity indication is used. OFC heat sinks and copper-plated heat sinks are used. Gold-plated low contact resistance input/output pin jacks are used. High sound quality capacitors and high-precision parts are used. Gold-plated terminals are used for the headphone jack. Three nitrogen gas-filled gold-plated relays are used. An autoloading cassette door is used, which closes automatically when a cassette is inserted. A super bias circuit is used. Equipped with a low-noise microphone amplifier with gain switching. It has a 3-mode display ON/OFF switch; when OFF, the clock stops. A low-distortion oscillator output is available for calibration of other decks and speaker phase checks. Quick response AI mechanism. It has a linear counter with pre-endo indicator. It has a large FL multi-mode display and a peak meter with 24-segment x 2-channel peak hold (Auto/Manual Reset available). It has heavyweight sidewoods with UV coating.Shipping FedEx?or DHLInternational Buyers - Please Note:Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying. Thank you for your understanding.

AIWA XK-S9000 HI-FI Stereo Cassette Deck No Tested Junk For Parts F/S Japan Description AIWA XK-S9000 ?Electricity has been confirmed. Since I have no specialized knowledge, I have not confirmed any other operations. Therefore, I am selling it as a junk item. Payment Most buyers can choose from any of the following payment methods: Visa, Mastercard, American Express, PayPal Apple Pay (through the eBay app and eBays mobile website only) Google Pay (through the eBay app, eBays mobile website, and desktop) Shipping It will be shipped from Japan. It will be shipped by Japan Post or FedEx. We will do our best to make sure that it reach you safely. Terms of Sale If you have any questions about our products, please feel free to contact us. International Buyers - Please Note: Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying. When returning an item, the purchaser is responsible for the paypal fee. Please understand. Thank You for taking the time to view this listing!! We wish you a great day! Many Thanks

Description A reference cassette deck developed for the best sound quality.The manual calibration which pulls out tape performance is carried. Furthermore, the built-in oscillator is set to 400Hz and 10kHz, allowing adjustment of wide frequency characteristics.In addition, since the level meter is expanded to 0.5dB steps during calibration, highly accurate calibration is possible.A three-step recording equalizer can be set according to the recording source and tape.High is a setting that emphasizes the low MOL (Maximum Output Level), Norm is the standard setting, and Low is a setting that emphasizes the high MOL.The low output-impedance power source by discrete composition is adopted.The PC-OCC low-capacity head wire is adopted and it is attached directly to the playback equalizer.The PC-OCC winding trap coil which uses a low-distortion core is adopted.The Dolby HX Pro circuitry of the discrete composition in which ON/OFF is possible is carried.The ultra-low distortion Dolby NR IC is carried.The high-precision detent type sound-recording volume is carried.A 70 micron thick copper foil printed circuit board is adopted.The special 3-layer structure large-sized metallized polyester film capacitor is adopted.The OFC extra-thick power cord with a polar display is adopted.An OFC heat sink and a copper-plated heat sink are used.The low contact resistance type input/output pin jack plated with gold is adopted.A high-quality sound capacitor and high-precision parts are adopted.A gold-plated terminal is adopted as the headphone jack.Three nitrogen gas-filled gold-clad relays are used.The auto loading type cassette door is adopted, and if a cassette is put in, it will automatically close.The super bias circuit is carried.The low-noise microphone amplifier with gain switching is carried. Shipping All shipments have tracking.I will carefully deliver using the packing material.I ship by FedEx or DHL or JapanPost. International Buyers - Please Note: Import duties, taxes, and charges are not included in the item price or shipping cost.These charges are the buyers responsibility.Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying.?Thank you for your understanding.

Here for sale is an Aiwa XK-S9000K Stereo Cassette Deck (UK plug). Almost looks like new, its hard to find even a small mark on it. Hardly had any use, its been in the loft for 15 years. A supremely collectable item. More info here... https://www.hifiengine.com/manual_library/aiwa/xk-s9000.shtml No scratches Wood finish is almost perfect Metal is in top condition Tape heads are fine Deck doesnt open (needs belts) No monitor source/tape switch No remote No box or instructions Aesthetically its almost perfect, its just been sitting in the loft for years and it needs a service / belts. I am too busy to do it and sadly need to sell because of personal circumstances. Happy shopping!

Vintage Aiwa XK-S9000 Stereo Cassette Deck Audio Equipment Very Rare ItemInternational Buyers - Please Note: Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying.

Vintage Aiwa XK-S9000 Stereo Cassette Deck Audio Equipment Very Rare ItemInternational Buyers - Please Note: Import duties, taxes, and charges are not included in the item price or shipping cost. These charges are the buyers responsibility. Please check with your countrys customs office to determine what these additional costs will be prior to bidding or buying.

Aiwa Xk-S9000 Stéréo Cassette PontCette fiche produit est originalement écrite en anglais. Veuillez trouver ci dessous une traduction automatique en français. Si vous avez des questions veuillez nous contacter.PaiementSoyez assuré que notre magasin offre une variété de méthodes de paiement.Veuillez payer dans les 5 jours suivant la fin de lenchère.À proposNous sommes situés au Japon. Pour les produits électriques, vérifiez le fabricant et le produit et convertissez-les à la tension de chaque pays. Nous prévoyons dexpédier par FedEx ou DHL. Veuillez nous contacter car les frais dexpédition peuvent être modifiés dans certains cas. Cest avec plaisir que nous vous ferons plaisir en vous proposant notre article recommandé.Si vous avez des questions ou des demandes concernant des articles, nhésitez pas à nous les demander.Acheteurs internationaux - Veuillez noter :-Les droits dimportation, les taxes et les frais ne sont pas inclus dans le prix de larticle ou les frais dexpédition. Ces charges sont sous la responsabilité de lacheteur.-Veuillez vérifier auprès du bureau de douane de votre pays pour déterminer quels seront ces coûts supplémentaires avant denchérir/acheter.-Ces frais sont normalement perçus par la société de livraison de fret (expédition) ou lorsque vous récupérez larticle - ne les confondez pas avec des frais dexpédition supplémentaires.-Nous ne marquons pas les valeurs des marchandises en dessous de la valeur ou ne marquons pas les articles comme - des cadeaux - Les réglementations gouvernementales américaines et internationales interdisent un tel comportement.]]>Nous sommes situés au Japon. Pour les produits électriques, vérifiez le fabricant et le produit et convertissez-les à la tension de chaque pays. Nous prévoyons dexpédier par FedEx ou DHL. Veuillez nous contacter car les frais dexpédition peuvent être modifiés dans certains cas. -Les droits dimportation, les taxes et les frais ne sont pas inclus dans le prix de larticle ou les frais dexpédition. Ces charges sont sous la responsabilité de lacheteur. -Ces frais sont normalement perçus par la société de livraison de fret (expédition) ou lorsque vous récupérez larticle - ne les confondez pas avec des frais dexpédition supplémentaires. -Nous ne marquons pas les valeurs des marchandises en dessous de la valeur ou ne marquons pas les articles comme - des cadeaux - Les réglementations gouvNous sommes situés au Japon. Pour les produits électriques, vérifiez le fabricant et le produit et convertissez-les à la tension de chaque pays. Nous prévoyons dexpédier par FedEx ou DHL. Veuillez nous contacter car les frais dexpédition peuvent être modifiés dans certains cas. -Les droits dimportation, les taxes et les frais ne sont pas inclus dans le prix de larticle ou les frais dexpédition. Ces charges sont sous la responsabilité de lacheteur. -Ces frais sont normalement perçus par la société de livraison de fret (expédition) ou lorsque vous récupérez larticle - ne les confondez pas avec des frais dexpédition supplémentaires. -Nous ne marquons pas les valeurs des marchandises en dessous de la valeur ou ne marquons pas les articles comme - des cadeaux - Les réglementations gouv Unit Type NA MPN NA Country Japan Brand Aiwa UPC NA Country/Region of Manufacture NA California Prop 65 Warning NA Model NA Unit Quantity NA

Aiwa Xk-S9000 Stereo Cassette DeckThis product data sheet is originally written in English.PaymentRest assured that our store offers a variety of payment methods.Please pay within 5 days after auction is finished.About UsWe are located in Japan.For electrical products, check the manufacturer and product and convert to the voltage of each country.We plan to ship by FedEx or DHL.Please contact us as the shipping fee can be changed in some cases. Its our pleasure to make you happy by proposing our recommend item.If you have any questions or request about items, please feel free to ask us.International Buyers - Please Note:-Import duties, taxes, and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.-Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying.-These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges.-We do not mark merchandise values below value or mark items as - gifts - The US and International government regulations prohibit such behavior.]]>We are located in Japan.For electrical products, check the manufacturer and product and convert to the voltage of each country.We plan to ship by FedEx or DHL.Please contact us as the shipping fee can be changed in some cases. -Import duties, taxes, and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. -Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. -These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges. -We do not mark merchandise values below value or mark items as - gifts - The US and International government regulations prohibit such behavior.We are located in Japan.For electrical products, check the manufacturer and product and convert to the voltage of each country.We plan to ship by FedEx or DHL.Please contact us as the shipping fee can be changed in some cases. -Import duties, taxes, and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. -Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying. -These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges. -We do not mark merchandise values below value or mark items as - gifts - The US and International government regulations prohibit such behavior. Unit Type NA MPN NA Country Japan Brand Aiwa UPC NA Country/Region of Manufacture NA California Prop 65 Warning NA Model NA Unit Quantity NA

PaymentRest assured that our store offers a variety of payment methods.Please pay within 5 days after auction is finished. About UsWe are located in Japan.For electrical products check the manufacturer and product and convert to the voltage of each country.We plan to ship by FedEx or DHL.Please contact us as the shipping fee can be changed in some cases. Its our pleasure to make you happy by proposing our recommend item.If you have any questions or request about items please feel free to ask us. International Buyers - Please Note:-Import duties taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility.-Please check with your countrys customs office to determine what these additional costs will be prior to bidding/buying.-These charges are normally collected by the delivering freight (shipping) company or when you pick the item up - do not confuse them for additional shipping charges.-We do not mark merchandise values below value or mark items as - gifts - The US and International government regulations prohibit such behavior.>