Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #4 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.The appearance is a beautiful product without any noticeable scratches. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories WeightsWeight fixing screwHead shell (Technics)Lead wireMounting nut/washerPHONO cableInstruction Manual (copy)(Japanese)Installation gauge (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #4 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed with the following contents. Output from both channels.Lifter descent speed (Oil refilled).Each adjustment point, operation feeling.Height adjustment, etc. Polished and cleaned for each part.The appearance is a beautiful product without any noticeable scratches. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories WeightsWeight fixing screwHead shell (Technics)Lead wireMounting nut/washerPHONO cableInstruction Manual (copy)(Japanese)Installation gauge (copy) Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer’s responsibility.Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as “gifts” -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

Hallo ebay Freunde ! Wegen Anschaffung einer neuen Anlage verkaufe ich hier schweren Herzens zu einem Sofortkaufpreis von 349 € inklusive kostenlosem Versand innerhalb Deutschlands meinen TECHNICS HIGH-END 5.1 DOLBY SURROUNG RECEIVER, MODELL SA-DA10 Das Gerät ist optisch in einem fast neuwertigen Zustand und ist seit der Anschaffung in meinem Besitz.Ich liefere ohne Originalverpackung, aber mit Fernbedienung und Bedienungsanleitung Der Receiver hat eine wahnsinnig gute Klangqualität und lief bis zuletzt, leider haben die Digitalausgänge ab und zu einen kleinen Wackelkontakt, was aber kaum die Freude am perfekten Klang beeinträchtigt.Weiterhin ist der hinten verbaute Gehäuselüfter nur noch mit externem Netzteil zu betrieben, da die interne Platine wohl einen Defekt hat. Das leistungshungrige Gerät benötigt eben Kühlung.Der versierte Bastler wird dies beheben können. Hier die technischen Daten:Tuning range: FM, MWPower output: 100 watts per channel into 6? (stereo)Surround output: 100W (front), 100W (center), 100W (rear)Frequency response: 10Hz to 70kHzTotal harmonic distortion: 1%Input sensitivity: 3mV (MM), 200mV (line)Signal to noise ratio: 80dB (MM), 100dB (line)Channel separation: 55dB (line)Output: 200mV (line)Speaker load impedance: 4? to 16?Digital inputs: coaxial, opticalVideo Connections: composite, SVHSDimensions: 430 x 180 x 370mmWeight: 12.7kgAccessories: remote control Sollten Sie mit meinem Preis nicht ganz einverstanden sein, machen Sie mir bitte einfach einen realistischen Preisvorschlag, vielen Dank! Da ich Privatperson bin und es sich hierbei um Privatverkauf handelt, weise ich darauf hin, dass ich jegliche Gewährleistung und Garantieansprüche ausschließe, wenn nicht anders angegeben. Außerdem ist eine Rücknahme nicht möglich.Mit Ihrem Gebot erklären Sie sich damit einverstanden. Sehen Sie sich gerne meine Bewertungen an: Meine Ware war stets meiner Artikelbeschreibung entsprechend und niemand war bisher unzufrieden. Das ist bei mir Ehrensache. Wenn einmal etwas nicht in Ordnung sein sollte so bitte ich gerne um Kontaktaufnahme - in der Regel melde ich mich umgehend zurück - wir werden dann eine Lösung finden. Von negativen Bewertungen bitte ich abzusehen. Ich wünsche viel Spaß beim Bieten oder Ersteigern !!!

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #3 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed.The appearance is a beautiful product without any noticeable scratches. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories All accessories are shown in the photos. Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer?s responsibility.Please check with your country?s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as ?gifts? -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

TECHNICS TESA1-090110d Power Supply Adaptor 9V -1.1A OEM Switching Ac Adapter

Unit powers on but has no output. Therefore it is being sold as is and for parts or repair. For cosmetic condition please refer to photos. Please only bid on this item with the understanding that it does not fully functional. There is no returns. It will be packed in a brand-new box using multiple layers of large bubble wrap, styrofoam sheeting and/or styrofoam filler to ensure safe delivery.

Technics SA-DA10 Digital Receiver AV Home Theater Amplifier GOLD BiAmp Mosfet. Technics SA-DA10 Digital Receiver AV Home Theater Amplifier GOLD BiAmp Mosfet Description Our SKU: 314302833159-3S74ZDZ Item Brand: Technics Item MPN: SA-DA10 Technics SA-DA10 Digital Receiver AV Home Theater Amplifier GOLD BiAmp Mosfet. Please let us know if you have any questions regarding a past or future purchase. Check out our entire store for more great products and deals!! Warranty Our inventory is purchased from various different manufacturers, retailers, and 3rd party sources. We do not represent or make any claim regarding any manufacturers warranty. We do however make every possible attempt to accurately describe the inventory we sell and stand behind it. We offer a no-questions asked 30-day return policy on everything we sell if the item is in the same condition it was sold in. If you have any issues at all with your purchase please feel free to contact us, we want to make it right!! Shipping All items are carefully packed and properly protected for shipment. We use several different carriers and choose the most economical for the item and destination based on the estimated handling and transit time. Please make every attempt possible to verify that part/product being purchased is correct for your application In the event of shipping damage, item not as expected, or any other reason to desire to return the product, please feel to contact us. At this time we do not offer internation shipping. About 8TEN Industries Since 2016, 8TEN Industries has been a leading asset recovery provider supporting national retailers, brands, and manufacturers. Our 60,000 square foot processing and distribution facility located in Cass City, Michigan has allowed us to become industry leader in turning difficult problems for manufacturers into great deals for our customers. More Items Store Contact Follow Us 8TEN Industries

Technics EPA-100 Dynamic Damping Universal Tone Arm Pickup Arm Vintage Audio #3 Domo Arigato! Welcome, Thank you for your visit. Description Operation confirmed.The appearance is a beautiful product without any noticeable scratches. Please refer to the photo. Overview The universal tone arm was developed to address the major issue of low-frequency resonance damping in pickup systems. The variable dynamic damping mechanism is capable of properly damping low-frequency resonances of both high and low compliance types, bringing out the full potential of the cartridge. The main weight is split and supported by a spring on one side, and floats on the other side by the attractive force between two magnets placed opposite each other at the rear of the weight and the damping selector. The resonance of the weight is damped by viscous silicon oil and a damping cylinder, effectively damping the resonance of the entire pickup system and successfully reducing resonance to less than half that of conventional systems. The resonance frequency of the main weight can be adjusted with the damping selector at the rear of the main weight according to the cartridge compliance, and the amount of braking can be set to an appropriate value. The arm pipe, 9.5 mm in outer diameter and 0.5 mm thick, is made of titanium nitride pipe arm, which is made of lightweight and mechanically strong titanium that has been further hardened by nitrogen. The tone arms support structure is made of titanium nitride pipe. Both the horizontal and vertical rotation sections of the tone arm are supported by a gimbal suspension system that uses bearings with high-precision pivot bearings manufactured in-house. The horizontal and vertical rotation axes intersect at a single point, minimizing differences in initial sensitivity and sensitivity in all rotation directions. Rubies, whose coefficient of friction is about 1/3 that of steel, are super-finished into balls with a sphericity of ±0.5?m, and 20 rubies are used.Combined with the gimbal suspension system, it achieves a high initial sensitivity of 5mg. Specifications Type: Universal tone arm with variable dynamic dampingEffective bearing clearance: 30mm both horizontally and verticallyArm pipe: Boron Titanium pipeArm effective length: 250mmArm length range: 322mm to 350mmArm rear length range: 66.5mm - 94.5mmArm height adjustment range: 44mm - 64mm (helicoid part 20mm)Overhang: 15mmHorizontal tracking error angle: +1°6(inner circumference of 30cm record), +2°6(outer circumference of 30cm record)Rotation axis sensitivity: Horizontal, vertical, initial sensitivity 5mgArm effective weight: 22g (cartridge dead weight 6.5g, needle pressure 1.25g)Arm resonance frequency: 9.8Hz, (Compliance: 12x10-6cm/dyne, cartridge weight 6.5g, needle pressure 1.25g)Arm resonance sharpness (Q): 6dB or less (at optimum adjustment)Needle pressure adjustment range: 0 to 3gShell weight: 9.5g (boron aluminum)Shell terminal lug: 1.2mm?, lug for 4-pin terminalApplicable cartridge weight: 5g to 10gArm mounting hole diameter: 62mm? Accessories All accessories are shown in the photos. Shipping Shipping is only available to the address registered in eBay. Shipping is by FedEx or EMS. Free Shipping Returns Unconditional Return Policy Customer service and satisfaction are very important to us.I have an unconditional return policy if notified within 30 of the receipt of the item. All returned items must be the original condition.All return requests must be made within 30 days of the receipt of the item. Please contact me first for return before you ship it back to me.The postage of the returned goods is a buyer burden. International Buyers Please Note:Import duties, taxes and charges are not included in the item price or shipping charges.These charges are the buyer?s responsibility.Please check with your country?s customs office to determine what these additional costs will be prior to bidding/buying.These charges are normally collected by the delivering freight (shipping) company or when you pick the item up -do not confuse them for additional shipping charges.We do not mark merchandise values below value or mark items as ?gifts? -US and International government regulations prohibit such behavior. I am sorry but we can not arrange that because it is illegal in Japan.Thank you.

TECHNICS TESA1-090110d Power Supply Adaptor 9V -1.1A OEM Switching Ac Adapter

Technics SA-DA10 Vintage AV Control Stereo Receiver Amplifier Working. Fully working on all inputs and speaker outputs. The lower plastic base seems to be missing and i'm not sure if the white lights on the front illuminate or not.

Lot x 2 TECHNICS TESA1-090110d Power Supply Adaptor 9V -1.1A OEM Switching Ac Adapter

TECHNICS TESA1-090110d Power Supply Adaptor 9V -1.1A OEM Switching Ac Adapter

Technics SA-DA10 Digital Receiver AV Home Theater Amplifier GOLD BiAmp Mosfet. Technics SA-DA10 Digital Receiver AV Home Theater Amplifier GOLD BiAmp Mosfet Description Our SKU: 314302833159-3S74ZDZ Item Brand: Technics Item MPN: SA-DA10 Technics SA-DA10 Digital Receiver AV Home Theater Amplifier GOLD BiAmp Mosfet. Please let us know if you have any questions regarding a past or future purchase. Check out our entire store for more great products and deals!! Warranty Our inventory is purchased from various different manufacturers, retailers, and 3rd party sources. We do not represent or make any claim regarding any manufacturers warranty. We do however make every possible attempt to accurately describe the inventory we sell and stand behind it. We offer a no-questions asked 30-day return policy on everything we sell if the item is in the same condition it was sold in. If you have any issues at all with your purchase please feel free to contact us, we want to make it right!! Shipping All items are carefully packed and properly protected for shipment. We use several different carriers and choose the most economical for the item and destination based on the estimated handling and transit time. Please make every attempt possible to verify that part/product being purchased is correct for your application In the event of shipping damage, item not as expected, or any other reason to desire to return the product, please feel to contact us. At this time we do not offer internation shipping. About 8TEN Industries Since 2016, 8TEN Industries has been a leading asset recovery provider supporting national retailers, brands, and manufacturers. Our 60,000 square foot processing and distribution facility located in Cass City, Michigan has allowed us to become industry leader in turning difficult problems for manufacturers into great deals for our customers. More Items Store Contact Follow Us 8TEN Industries

Unit powers on but has no output. Therefore it is being sold as is and for parts or repair. For cosmetic condition please refer to photos. Please only bid on this item with the understanding that it does not fully functional. There is no returns. It will be packed in a brand-new box using multiple layers of large bubble wrap, styrofoam sheeting and/or styrofoam filler to ensure safe delivery.

Technics SA-DA10 Vintage AV Control Stereo Receiver Amplifier. In good working order. Phono out has an intermittent dropout, if connected to a TV via HDMI Sound is perfect. Case has a few scratches on side see photos. Specifications in photos. Amp has outlets for rear and centre speakers.On 12-Apr-23 at 14:17:56 BST, seller added the following information: Come with remote control

Unit powers on but has no output. Therefore it is being sold as is and for parts or repair. For cosmetic condition please refer to photos. Please only bid on this item with the understanding that it does not fully functional. There is no returns. It will be packed in a brand-new box using multiple layers of large bubble wrap, styrofoam sheeting and/or styrofoam filler to ensure safe delivery.

Unit powers on but has no output. Therefore it is being sold as is and for parts or repair. For cosmetic condition please refer to photos. Please only bid on this item with the understanding that it does not fully functional. There is no returns. It will be packed in a brand-new box using multiple layers of large bubble wrap, styrofoam sheeting and/or styrofoam filler to ensure safe delivery.