Bought brand new from my local dealer less than a year or so ago and looks new with no visible blemishes that I can see excellent condition JC2 BP Preamp With remote.

Product highlights110 watts x 2 channels into 4 or 8 ohms (20-20,000 Hz) at 0.05% THD 4-ohm capability allows use with a wide range of speakers Burr-Brown 24-bit/192kHz digital-to-analog converter for high-performance playback of digital sources Class D amplifier design home theater bypass inputs for surround sound integration switchable high-pass crossover with variable settings (20-140 Hz) affects speaker-level outputs and main preamp outputs front-panel multi-function input knob also controls treble, bass, balance and subwoofer volume frequency response: 20-20,000 Hz (+0/-0.05dB) signal-to-noise ratio: 80dB (phono), 100dB (line); 110dB (digital) dimmable front panel LCD display remote control included rack mountable with the optional RMK 11 kit detachable power cord 1 optical and 1 coaxial digital audio input (up to 24-bit/192kHz resolution) USB Type-B input for connecting a computer (up to 24-bit/96kHz resolution) three stereo RCA audio inputs input 1: switchable line/phono stage for moving magnet and moving coil cartridges front-panel 3.5mm auxiliary input for connecting a portable audio player shared with rear analog input 3 - plugging source into front panel aux disables rear analog input 3 bypass inputs stereo RCA inputs allow amplifier section to power front left/right speakers in a surround sound system connected preamp/processor must have a volume control dual mono RCA subwoofer inputs route processors subwoofer signal to integrated amps subwoofer outputs built-in headphone amplifier with front-panel 3.5mm jack stereo RCA main preamp output fixed stereo RCA record out dual mono RCA subwoofer outputs output 1: subwoofer only (low pass filter output 2: full range mono output for subwoofer or mono listening area heavy-duty gold-plated speaker terminals 12-volt trigger output IR remote input RS-232 port for third-party remote control 17-1/4W x 2-1/2H x 17-1/16D (1U rack space) weight: 11.5 lbs. warranty: 2 years Whats in the boxIntegrated amplifier 6 AC power Cord Remote control (NC22) 2 AA batteries 39 USB-A to USB-B cable Owners Manual About this itemWritten by Crutchfields Eric A.A low-profile integrated amplifier Parasounds NewClassic 200 integrated amplifier is just 2-1/2 tall, but it packs a lot of features into that space-saving chassis. It delivers 110 watts per channel into an 8- or 4-ohm load, so you can use it with a wide variety of speakers. Its great for music listening, but it also offers a convenient set of bypass inputs, so you can use it in conjunction with a surround sound receiver or processor to drive the front left/right speakers in a home theater system, too. Convenient connections This amp offers three unbalanced RCA inputs for connecting analog sources. Input 1 is switchable, so you can use it as a line input or as a phono stage for moving magnet and moving coil cartridges. The NewClassic 200 has a built-in DAC that makes digital sources sound great — there are single optical and coaxial inputs on the back panel, plus a USB Type-B port for connecting a computer. The 3.5mm auxiliary input on the front panel is designed for playing music from a portable audio player. In addition to a pair of binding post speaker terminals, there are main preamp and subwoofer outputs. If you have a sub in your system, you can switch on the adjustable high-pass crossover. That way, the amplifier will only reproduce frequencies that arent covered by your sub, giving you the most efficient use of your available power.

Product highlights90 watts per channel into 8 ohms (20-20,000 Hz) at 0.35% THD with 2 channels driven 150 watts x 2 into 4 ohms (2-ohm stable with load selector switch) 200 watts x 1 at 8 ohms in bridged mode Class AB amplifier design high-current toroidal transformer frequency response: 20-50,000 Hz (+0/-3dB) signal-to-noise ratio: 110 dB switchable high pass filter: off/20Hz/40Hz unbalanced stereo RCA inputs with loop output right and left level knobs (total gain of 28 dB) 2 pairs of binding post speaker connectors A+B speaker impedance switch: 2-3 ohms/4-8 ohms front-panel A/B speaker selector buttons with rear-panel lockout switch switchable turn-on options: manual, signal sensing, or 12-volt trigger detachable power cord rack mountable with the optional RMK 11 kit 17-1/4W x 2-1/2H x 15-3/4D (1U rack space) weight: 20 lbs. warranty: 2 years Whats in the boxStereo power amplifier 6 AC power cord 6 2.5mm trigger cables 6 2.5mm-to 3.5mm trigger cable Rack-mount hardware Owners Guide About this itemWritten by Crutchfields Eric A.Solid power for one or more speakers Parasounds NewClassic 275 v.2 delivers a respectable 90 watts per channel, and has two sets of binding posts for connecting speakers. You can use it as a classic stereo amp for two-channel listening or set up A and B speaker pairs in two different rooms. It can also be bridged to 200 watts mono to drive a single speaker.

Up for sale is a working Halo Parasound C2 remote . Great condition, only a few minor surface scratches on screen . Batteries not included . Inventory D3

Product highlights150 watts per channel into 8 ohms (20-20,000 Hz) at 0.25% THD with 2 channels driven 225 watts x 2 into 4 ohms (2-ohm stable with load selector switch) 400 watts x 1 at 8 ohms in bridged mode Class AB amplifier design high-current toroidal transformer THX Ultra2 certified for reference home theater sound frequency response: 20-50,000 Hz (+0/-3dB) signal-to-noise ratio: 114 dB switchable high pass filter: off/20Hz/40Hz unbalanced stereo RCA inputs with loop output right and left level knobs (total gain of 28 dB) 2 pairs of binding post speaker connectors A+B speaker impedance switch: 2-3 ohms/4-8 ohms front-panel A/B speaker selector buttons with rear-panel lockout switch switchable turn-on options: manual, signal sensing, or 12-volt trigger detachable power cord rack mountable with the optional RMK 22 kit 17-1/4W x 4-1/8H x 16D (2U rack spaces) weight: 27 lbs. warranty: 2 years Whats in the boxStereo power amplifier 6 AC power cord 6 3.5mm trigger cable 6 2.5mm-to 3.5mm trigger cable Rack-mount hardware Owners Guide About this itemWritten by Crutchfields Eric A.A versatile power amplifier Parasounds NewClassic 2125 v2 is flexible enough to work in many different audio applications. It delivers 150 watts per channel and has two sets of binding posts for connecting speakers. You can use it as a classic stereo amp for two-channel listening, set up A and B speaker pairs in two different rooms, or combine it with additional 2125 amplifiers for THX Ultra2 certified home theater sound. This slim-but-powerful amp can also be bridged to 400 watts mono to drive a single speaker.

Product highlightsstereo preamplifier with analog and digital inputs to handle a variety of music sources frequency response: 20-20,000 Hz (+0/-0.05dB) signal-to-noise ratio: 100 dB line, 80dB phono total harmonic distortion: 0.05% Burr-Brown 24-bit/192kHz DAC front-panel volume control knob front-panel multi-function input knob also controls treble, bass, balance and subwoofer volume dedicated built-in headphone amplifier detachable power cord Inputs: 3 stereo RCA line-level analog inputs analog input 1 is 3-way switchable: line-level moving magnet phono moving coil phono front-panel 3.5mm aux input with automatic +12 dB gain stage shared with rear analog input 3 — plugging source into front panel aux disables rear analog input 3 bypass inputs for surround sound or music streamer integration stereo RCA left- and right-channel bypass inputs 2 mono subwoofer bypass inputs 200 Pres volume control doesnt affect bypass inputs; volume must be controlled at the source optical digital input (up to 24-bit/192kHz resolution) coaxial digital input (up to 24-bit/192kHz resolution) USB Type-B input for your computer (up to 24-bit/96kHz resolution) Outputs: stereo RCA main preamp output switchable high-pass crossover with variable settings (20-140 Hz) dual mono RCA subwoofer outputs output 1: subwoofer only (low pass filter output 2: full-range mono output for subwoofer or mono listening area stereo RCA fixed-level recording output front-panel 3.5mm headphone output remote control RS-232 control port for use with third-party automation systems 3.5mm IR repeater input and 12V trigger output 17-1/4W x 2-1/2H x 16-7/8D (1U rack space) Crutchfields in-house depth measurements are made with all relevant cables in place rack-mountable with the Parasound RMK 11, sold separately weight: 11 lbs. warranty: 2 years Whats in the boxStereo preamplifier 6 AC power Cord Remote control (NC22) 2 AA batteries 39 USB-A to USB-B cable 6 Mono-minijack cable Owners Manual About this itemWritten by Crutchfields Ned O.A lot of ways to listen to your sources Parasounds NewClassic 200 Pre preamp really impresses us with its sound quality and range of features — and its price. With optical, coaxial and USB digital inputs running through the 200s Burr-Brown 24-bit/192kHz DAC, the 200 will bring out the best from your digital sources. Three analog inputs — including a phono stage for moving magnet and moving coil cartridges — give you flexibility for your analog sources. If youre new to using a separate preamp, the 200 Pre is a great way to start, with its compact design, flexible system setup options, and clean, precise sound. Speaker options and control Along with its flexible input array, the 200 offers a number of useful ways to configure your speakers. It features two mono subwoofer outputs and a handy subwoofer level control thats accessible from the front panel. You can even use one subwoofer output to feed a mono full-range listening zone if, for example, you want music in the kitchen or bathroom off your main listening room. The 200s switchable, adjustable high-pass crossover comes in handy when youre using a subwoofer in addition to your main speakers. It allows your amp to reproduce only the frequencies that arent covered by your sub, giving you the most efficient use of your available power. Dedicated bypass inputs for mains and subwoofers let you integrate the 200 Pre seamlessly with your home theater setup.

Used for a few years works great, upgraded my setup so Im selling this one. Remote included, specs listed below Frequency Response 5 Hz - 100 kHz, +0/-3 dB Distortion THD: < 0.003% at 100 Hz THD: < 0.005% at 20 kHz IM: < 0.003% S/N Ratio > 116 dB, input shorted, IHF A-weighted > 104 dB, input shorted, unweighted Crosstalk > 100 dB at 10 kHz > 90 dB at 20 kHz Gain 14 dB, maximum L, R Gain Control Range - 10 dB Input Impedance Unbalanced: 30k ohms Balanced: 30k ohms per leg Output Impedance Unbalanced: < 60 ohms Balanced: < 60 ohms per leg Input Sensitivity 200 mV for 1 V output Total Gain: 14 dB Maximum Output: 8 V XLR Pin Identification 1 = Ground (Shield) 2 = Positive 3 = Negative (Return) AC Power Requirement 110 - 120 V or 220-240 V, 50 - 60 Hzs (Set AC Voltage switch on rear panel) 25 watt standby; 30 watts when turned on

Edwards Home Entertainment and Design, an appointed and displaying dealer for Bowers & Wilkins, Focal, NAIM, Parasound, Classe Audio, Rotel and Michi, Fyne Audio, Rel Acoustics, JL Audio, Perlisten, Soul Note, Marantz, Lumin, and Nordost, as well as part of the Verified Dealer Program here on eBay, is offering this fantastic Parasound JC2BP. This preamp is in fine shape, without issue.  Cosmetically clean, operationally sound.  The JC2BP will come complete with remote, manual, factory packaging and boxes. Buy / Sell / Trade / Consign - Edwards Home Entertainment and Design (EHEAD) has been a premier seller of carefully selected, pre-loved high end audio equipment since 1997. Now an authorized dealer for Parasound (displaying JC-1+, HINT 6, JC-5, JC-3+), Bowers & Wilkins (displaying 801D4, 802D4, 803D4, 804D4, 805D4, 702S3, and the 705S3), Classe Delta (displaying the Delta Pre, Delta Stereo, Delta Monos), Focal (displaying Scala EVO, Sopra3, Sopra 2), NAIM (displaying the SuperNAIT3), Rotel Michi (displaying the P5, S5), Fyne Audio (displaying F1-12, 502SP, F700), Marantz (displaying PM-10 Integrated, SA-10 Super Audio SACD/CD Player, TT-15S2 TurnTable), Rel Acoustics (displaying the Carbon Special, S/812 and S/512), Lumin (displaying the newest P1, T3, D3, and U2 Mini),  Perlisten (displaying the 7St, and D212), JL Audio (displaying the G213v2, F113v2, D and E subs), Soul Note (displaying the A2 integrated), Nordost (displaying Norse and Leif series, with demo cases for in home trials), SolidSteel (displaying HyperSpike and S3 walnut), Finite Element (displaying Pagode) and NEO Luxury Audio Racks (displaying the Quattron), and Bossocontinuo (displaying the McRack) Reference and Classic. Visit the EHEADAudio site in South San Francisco via direct phone / voice / or text.   We are always looking to buy quality used gear.  Despite listings that may indicate LOCAL PICK UP ONLY - this is just to facilitate posting of gear. Logistics is our specialty, we can facilitate packaging and shipping to and from anywhere in the country. If you are interested in our gear, please reach out and we can figure out a shipping solution that will work. Our shop is in South San Francisco - stop by and put your eyes and ears to work!

Parasound A52 And C2. Dolby digital surround sound processor and Amp. Being sold as a set. Units power up, they were unhooked when we removed, so we did not hear the system. A52 Amp is 55lbs and the C2 surround sound processor is 18lbs - buyer to pay all shipping costs. https://parasound.com/pdfs/A52+%20Manual.pdf https://parasound.com/vintage/c2.php

Edwards Home Entertainment and Design, an appointed and displaying dealer for Bowers & Wilkins, Focal, NAIM, Parasound, Classe Audio, Rotel and Michi, Fyne Audio, Rel Acoustics, JL Audio, Perlisten, Soul Note, Marantz, Lumin, and Nordost, as well as part of the Verified Dealer Program here on eBay, is offering this fantastic Parasound JC2BP. This preamp is in fine shape, without issue.  Cosmetically clean, operationally sound.  The JC2BP will come complete with remote, manual, factory packaging and boxes. Buy / Sell / Trade / Consign - Edwards Home Entertainment and Design (EHEAD) has been a premier seller of carefully selected, pre-loved high end audio equipment since 1997. Now an authorized dealer for Parasound (displaying JC-1+, HINT 6, JC-5, JC-3+), Bowers & Wilkins (displaying 801D4, 802D4, 803D4, 804D4, 805D4, 702S3, and the 705S3), Classe Delta (displaying the Delta Pre, Delta Stereo, Delta Monos), Focal (displaying Scala EVO, Sopra3, Sopra 2), NAIM (displaying the SuperNAIT3), Rotel Michi (displaying the P5, S5), Fyne Audio (displaying F1-12, 502SP, F700), Marantz (displaying PM-10 Integrated, SA-10 Super Audio SACD/CD Player, TT-15S2 TurnTable), Rel Acoustics (displaying the Carbon Special, S/812 and S/512), Lumin (displaying the newest P1, T3, D3, and U2 Mini),  Perlisten (displaying the 7St, and D212), JL Audio (displaying the G213v2, F113v2, D and E subs), Soul Note (displaying the A2 integrated), Nordost (displaying Norse and Leif series, with demo cases for in home trials), SolidSteel (displaying HyperSpike and S3 walnut), Finite Element (displaying Pagode) and NEO Luxury Audio Racks (displaying the Quattron), and Bossocontinuo (displaying the McRack) Reference and Classic. Visit the EHEADAudio site in South San Francisco via direct phone / voice / or text.   We are always looking to buy quality used gear.  Despite listings that may indicate LOCAL PICK UP ONLY - this is just to facilitate posting of gear. Logistics is our specialty, we can facilitate packaging and shipping to and from anywhere in the country. If you are interested in our gear, please reach out and we can figure out a shipping solution that will work. Our shop is in South San Francisco - stop by and put your eyes and ears to work!

10 X 14. Unused from when i built our house. They are very good speakers. Ask any questions

Here is a Parasound Halo C2 AV controller. It comes with its remote, a microphone and user manual. Nothing else supplied... only what you see in the pictures. Condition report: The pre amplifier initially looks great, but the top panel is suffering from some surface corrosion and there there are one or two nicks here and there elsewhere. If viewed from the front and used within a rack, itll look great, but as a whole unit we can only describe it as average condition at best. In use: We have tested this pre amplifier and all controls work as expected. No issue. Summary: A capable AV pre-amplifier thats working well, but with a case where the top panel is suffering from corrosion spots. The small print...The photographs show the actual item being sold. I use a studio to show the items in as much detail as possible. I must stress, that I have not serviced this item, just described its current cosmetic and operational condition as honestly as I can. PACKAGINGI only use brand new double wall boxes and all internal packaging is via ethafoam... this is the perfect foam to keep items well located and far superior to bubble wrap. POSTAL AREA EXCEPTIONSPlease note that standard UK postage does not include Channel Islands, Isle of Man, Isle of Wight, Northern Ireland, Scilly Isles, Scottish Highlands, Scottish Islands. Thank you. DELIVERY - PLEASE READ VERY CAREFULLYI send all UK deliveries by DPD next day delivery. Please be sure someone is present to sign for your package. If you are not present, please reschedule your delivery for when you are present. Please do NOT enable a safe place option where the courier can put your large box with its precious hifi vaguely behind a bin where it can be seen by passers by... it may not be there when you get home! My contract with DPD is for a signed for service. If you override this and ask for an item to be left in a safe place then I will NOT be held responsible for any item that is stolen. Be assured that DPD will also not reimburse you. Finally, please be aware that DPD will hold your preferences on its system from a previous delivery, so if you have previously selected a safe place delivery, this will automatically be DPDs default position if you are not there to receive the item.