Unit is in good physical condition (see pics for details). One channel does not have output.... However transistor tested good. Other channel okay. Thanks for the read Kj6pwp

Dynaco SCA-80Q Dynaquad 4 Dimensional Integrated Amplifier. I took this unit to my tech to look over. He cleaned the controls and switches and looked over the unit. The treble knob is very stiff but works. When you switch the tape monitor there's a fuzzy sound during the switching, but once switched there's no issue. Other than that everything works fine. The unit measures 13 by 10.5 by 4.

This is the legendary SCA-50 created by David Hafler in the 70s. Extremely clean and solid for its power rating. Along with the many inputs it also supplies 3- AC outlets 2-switched with the power switch and the other outlet servers as a through AC outlet for use with other components.SpecificationsPower output: 25 watts per channel into 8? (stereo)Frequency response: 15Hz to 45kHzTotal harmonic distortion: 0.25%Input sensitivity: 1.65mV (MM), 125mV (line)Channel separation: 60dB (line)Semiconductors: 2 x IC, 2 x FET, 17 x transistors, 24 x diodesDimensions: 13-1/2 x 12 x 4-1/4 inchesWeight: 15lbs

Last time this was used it worked but had a 60hz hum. Currently it powers up but I did not try to connect it to an input source or speakers.

Dynaco SCA-80Q Dynaquad 4 Dimensional Integrated Amplifier. I took this unit to my tech to look over. He cleaned the controls and switches and looked over the unit. The treble knob is very stiff but works. When you switch the tape monitor there's a fuzzy sound during the switching, but once switched there's no issue. Other than that everything works fine. The unit measures 13 by 10.5 by 4.

Dynaco SCA-80Q Dynaquad 4 Dimensional Integrated Amplifier, Kinda Works*. We tested this, hooked it up to speakers, and it turned on fine, but there are a few issues. *The main speaker output works just fine, but the balance control does not work. For the secondary speakers output, only one channel seems to work. But, it comes with a very comprehensive manual for repairs! Please see all photos and I am happy to answer any questions. Thanks

Vintage Original Dynaco PC-11 SCA-35 Circuit board, nice well cared for complete condition, quality made and designed in the USA, 1960s. The shipping cost includes fast prompt insured with tracking number. Buy with confidence, see my feedback. Good listening, SonnY :)

This is the legendary SCA-50 created by David Hafler in the 70s. Extremely clean and solid for its power rating. Along with the many inputs it also supplies 3- AC outlets 2-switched with the power switch and the other outlet servers as a through AC outlet for use with other components.SpecificationsPower output: 25 watts per channel into 8? (stereo)Frequency response: 15Hz to 45kHzTotal harmonic distortion: 0.25%Input sensitivity: 1.65mV (MM), 125mV (line)Channel separation: 60dB (line)Semiconductors: 2 x IC, 2 x FET, 17 x transistors, 24 x diodesDimensions: 13-1/2 x 12 x 4-1/4 inchesWeight: 15lbs

Offered for sale is a manual for Instructions for Assembly Operation for the Dynaco SCA-50 Amplifier. This is a copy. 12 pages, in good condition with no writing or marks on the pages. Please review the pictures to see the condition.

Dynaco SCA-80Q Dynaquad 4 Dimensional Integrated Amplifier. I took this unit to my tech to look over. He cleaned the controls and switches and looked over the unit. The treble knob is very stiff but works. When you switch the tape monitor there's a fuzzy sound during the switching, but once switched there's no issue. Other than that everything works fine. The unit measures 13 by 10.5 by 4.

DYNACO SCA-35 stereo tube amplifier 2-PARTS COVER LOT (TOP AND BOTTOM) as pictured, they pulled, in clean and good condition as shown. Note: This item is intending for professional (whom who know it well) and it is final (NO RETURN OR REFUND) Please buy or bid accordingly. Thanks for looking.

DYNACO CONTROL KNOB for SCA-35 PAS3 PAS VOLUME & FUNCTION SELECTOR as pictured, it pulled, 1 1/4 DIAMETER, in good condition (set screw is intact) as shown. Note: This selling is final (no return or refund). Please buy or bid accordingly. Thanks for looking.

DYNACO small original OEM CONTROL KNOB for PAS 3 preamplifier, SCA-35 amplifier as pictured, its in good condition as shown, dimension = 3/4 diameter, pure aluminum metallic texture. Note: The US-Penny is using as relative scaling purpose only and this selling is final (no return or refund) Please buy or bid accordingly. Thanks for looking.

Vintage DYNACO SCA-35 Tube Integrated Stereo Amplifier - Factory Wired. Selling for parts or repair Vintage amp Powers on but unable to test further Selling as-is See pics for item details Shipping Fed Ex

Vintage Original Dynaco PC-11 SCA-35 Circuit board, nice well cared for complete condition, quality made and designed in the USA, 1960s. The shipping cost includes fast prompt insured with tracking number. Buy with confidence, see my feedback. Good listening, SonnY :)

This is the legendary SCA-50 created by David Hafler in the 70s. Extremely clean and solid for its power rating. Along with the many inputs it also supplies 3- AC outlets 2-switched with the power switch and the other outlet servers as a through AC outlet for use with other components.SpecificationsPower output: 25 watts per channel into 8? (stereo)Frequency response: 15Hz to 45kHzTotal harmonic distortion: 0.25%Input sensitivity: 1.65mV (MM), 125mV (line)Channel separation: 60dB (line)Semiconductors: 2 x IC, 2 x FET, 17 x transistors, 24 x diodesDimensions: 13-1/2 x 12 x 4-1/4 inchesWeight: 15lbs

A RARE AMERICANCLASSIC The Dynaco SCA-35, the only integrated valve amplifier made by the very successful American tube amplifier company Dynaco. Whilst very popular in the USA, these are rare in the UK. This model was introduced in 1964. An online review on TNT-Audio.com praises its enjoyable sound: ‘Overall, the SCA-35 is a wonderful integrated amplifier and can be listened to for hours and hours.’ (https://www.tnt-audio.com/ampli/dynaco-sca35_e.html) This particular unit has the American 120V power transformer, but it works well in the UK with a simple 240V to 120V voltage transformer which is readily available from Amazon, eBay, etc. It is fitted with the original two-prong USApower cord. ALL VALVES INCLUDED· 2 x ECC83s (Matsushita and Mazda)· 2 x ECF82 (Mazda and KK)· 4 x EL84s (Electro Harmonix, Golden Dragon,unbranded and Zaerix) REPAIRS AND UPGRADES The unit has some cosmetic damage, but it has been repaired and rebuilt. It is in working order with the following upgrades: The output transformers have been replaced by Oxford Electrical Products transformers (part number D29A09F) with ultralinear taps, just as the originals. These are made in Oxford, UK. The old phenolic printed circuit boards (PCBs) have been upgraded with new, high quality fibre glass ones, designed and made in the USA by respected audio engineer David Gillespie. The power boardshave been redesigned and remanufactured to use easily available ECF80 0r ECF82valves in place of the much scarcer 7199 valves. The preamp board, with facilities for record playback, is as per the original design, but reproduced on a new fibreglass PCB board. The original power supply has been replaced by a new, modern capacitor board which incorporates Gillespie’s EFB (Enhanced Fixed Bias) circuit. This supplies increased power storage and converts the EL84 valves to fixed bias operation for increased power and reduced distortion. The front controls have been upgraded with new high-quality knobs and the old power on/off bulb indicator has been replaced with a bright LED. The loudness compensation switch is disengaged because it requires a specialised volume control potentiometer. The one in this unit was faulty and had to be replaced. These pots are now available from the USA so this control could be reinstated quite simply, if desired. The previous owner cut the rear panel to replace the input sockets with new gold-plated onesand the output screws with banana sockets. This was done rather clumsily, but the replacementsockets are convenient and the cut in the rear panel is not visible from thefront. Because of the popularity of Dynaco tube amplifiers in the USA, spare parts are readily available for the buyer who would like to restore it to mint original cosmetic condition. DOCUMENTATION Copies of the original Instructions for Assembly and Operation, with pictorial diagrams and the assembly and installation guides for all four new D Gillespie Designs boards are included. CONDITION While the chassis has been cut in places, the amp has been completely rebuilt and is in working order. If collected, this can be demonstrated to the buyer. Shipping is at the buyer’s own risk, but it will be well-packed. The valves will be individually and securely wrapped and placed inside the cage. SAFETY If shipped, it should be visually inspected before use to check that there is no transit damage, e.g. wires shaken loose. Because of the high voltage inside the chassis, the amplifier should always be operated with the cover on and securely attached. SHIPPING International shipping via the Ebay global shipping programme.

Ampli Dynaco Sca 35. En superbe état entièrement révisé. Modifié pour accueillir les tubes 6GH8A en lieu est place des 7199. Opération effectuée par un professionnel de la hifi à tubes (facture fournie). La possibilité de revenir au 7199 est bien entendu possible. Fonctionnement parfait. Vendu sans ses tubes el84. Prévoir un quartet appairé. Notice et facture d’époque fournies Spécifications: Puissance de sortie : 17,5 watts par canal en 8? (stéréo) Réponse en fréquence : 20 Hz à 20 kHz Distorsion harmonique totale : 1 % Sensibilité d'entrée : 4 mV (MM), 1000 m V (ligne) Rapport signal/bruit : 70 dB (MM), 80 dB (ligne) Complément de valve : 2 x 12AX7, 2 x 6GH8A, 4 x 6BQ5/EL-84/7189

### The Audio Board: www.theAudioBoard.com - The Search Tool for Used High-End Audio Equipment### NO RESERVE AUCTION. MOVING SALE: A moving in the summer forces us to liquate my stuff before that. For sale is a vintage, one of the best sounding Dynaco SCA-35 Tube Amplifier, Factory Assembled The transformers are the same as those on Dynaco ST-35; considered one of the best sounding EL84-based amplifiers. This SCA-35 has been modified by the original owner to by-pass the phono and line stage. The input is fed by two RCA cables and is routed to the power amplifier unit. It works as a stereo power amplifier. It can be restored to original SCA-35 by some professional but I have no idea how. No tubes are included. I borrowed needed tubes for testing. The amp worked and produced good music but there was some hum. Apparently, this amp will need service first, before daily use. Physical condition is as shown. Front plate is fine but all knobs have been removed. The top cover has some rust. Bottom plate is present. Ill pack well and ship worldwide. I have other audio equipment, like Accuphase, Acurus, Adcom, Aragon, Arcam, Audio Research, Audioquest, Ayre, B&K, B&O, Bang Olufson, B&W, Bowers Wilkins, Bryston, California Audio Labs, Cary, Classe, Cambridge, Carver, Conrad Johnson, Creek, Denon, Dynaco, Dynaudio, Goldmund, Infinity, Jadis, JBL, Jolida, JM Lab, Kef, Kimber, Klipsch, Krell, Levinson, Lexicon, Linn, Marantz, Martin Logan, Mccormack, Mcintosh, Meridian, MIT, Musical Fidelity, Music Hall, NAD, Naim, Nakamichi, NHT, Paradigm, Parasound, Pass, Pioneer, Proceed, PS Audio, PSB, Quad, Rega, Revel, Rotel, Rowland, Sonic Frontiers, Sonus Faber, Spendor, Sunfire, Tandberg, Tannoy, Theta, Thiel, Threshold, Totem, Transparent, Vandersteen, Vmps, VPI, VTL, Velodyne, AR, Audio, Audiophile, Amplifier, Amps, Arcam, Acurus, Aragon, Adcom, ADS, Advent, Bose, Boston, Beovox, Bryston, Bedini, B&K, B&0, B&W, Bowers & Wilkins, Celestion, Counterpoint, Canton, Cello, Creek, Cerwin Vega, Dahlquist, Denon, Dcm, Dynaco, Dynaudio, Ess, Spica, Epicure, Ensemble, Electrostatic, Elite, Fisher, Fosgate, Harman kardon , Harbeth , Integra, Infinity, JBL, Jadis, Jolida, Linn, Luxman, KEF, Klipsch , KLH, Krell, Kenwood, Martin Logan, McIntosh, Mirage, Mission, Monitor Audio, Nad , Onkyo , Paradigm, Proac, Sony, Pioneer, Polk-Audio, Preamplifier, Quad ,Rogers, Rotel, Rega, Stanton, Speakers, Audio,Stereo,Studio, Vandersteen,, Snell, Spendor, Thorens, Vandersteen, Wharfedale, Yamaha, Speakers, Turntable, M&K, Accuphase, Dali, Wilson Audio, Sonus Faber, Definitive Technology, PSB, NHT, Magnepan, Eminent Technology, Monitor Audio, Vienna Acoustic, Meridian, Behringer, Acoustat, Genesis, Opera, Mirage, Energy, Pinnacle, Musical Fidelity, Sonic Frontiers, Cambridge Audio, Sunfire, Velodyne, SVS, HSU Research, Audio Research, Tannoy, Subwoofer, McCormack, Meadowlark, Conrad Johnson, Parasound, Magneplanar, Audible Illusions, Mark Levinson, Vintage, REL, Revel, Nakamichi, ESS, Emotiva.

Dynaco SCA-80Q Dynaquad 4 Dimensional Integrated Amplifier. I took this unit to my tech to look over. He cleaned the controls and switches and looked over the unit. The treble knob is very stiff but works. When you switch the tape monitor there's a fuzzy sound during the switching, but once switched there's no issue. Other than that everything works fine. The unit measures 13 by 10.5 by 4.

BEAUTIFUL DYNACO SCA-80Q DYNAQUAD AMPLIFIER ! v Track Page Views WithAuctivas Counter

A classic configuration original DYNACO POWER CORD for original lover or Dynaco value enhancement project (Dynaco PAS preamplifier, ST-35, ST-70, SCA-35 amplifier) as pictured. Its pulled, in good clean condition (checked) Note: This beautiful classic configuration also suitable for Fisher, Pilot, Eico, Scott etc... vintage audio equipment and this selling is final (NO RETURN OR REFUND) Please buy or bid accordingly. Thanks for looking.

Dynaco SCA-80Q Dynaquad 4 Dimensional Integrated Amplifier. I took this unit to my tech to look over. He cleaned the controls and switches and looked over the unit. The treble knob is very stiff but works. When you switch the tape monitor there's a fuzzy sound during the switching, but once switched there's no issue. Other than that everything works fine. The unit measures 13 by 10.5 by 4.

BEAUTIFUL DYNACO SCA-80Q DYNAQUAD AMPLIFIER ! v Track Page Views WithAuctivas Counter